Home » HP Manuals » Storage Devices » HP StorageWorks 2/16 » Manual Viewer

HP StorageWorks 2/16 HP StorageWorks SAN Switch 2/16 V3.1.2 (AA-RR84D-TE, May - Page 41

To con Port Settings in a UNIX, Flow control: None

View all HP StorageWorks 2/16 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Installing the SAN Switch 2/16 Note: These steps show instructions specific to HyperTerminal. If you are using a different application, consult that application's documentation. 6. Using HyperTerminal (or similar application), configure the Port Settings as follows: ■ Bits per second: 9600 ■ Databits: 8 ■ Parity: None ■ Stop bits: 1 ■ Flow control: None To configure Port Settings in a UNIX® environment, enter: tip /dev/ttyb -9600 7. Log in to the switch (with administrator privileges). The default administrator logon is admin and the default password is password. a. Enter the following at the prompt: ipAddrSet b. Enter the following information at the corresponding prompts listed below: - Ethernet IP Address [10.77.77.77]: Enter the new Ethernet IP address. - Ethernet subnetmask [0.0.0.0]: Enter the new Ethernet subnetmask. - Fibre Channel IP Address [none]: Enter the new Fibre Channel IP address if desired. - Fibre Channel Subnetmask [none]: Enter the new Fibre Channel subnetmask if desired. - Gateway Address [172.17.1.1]: Enter the new gateway address. - Set IP address now? [y = set now, n = next reboot]: Enter y to set now. SAN Switch 2/16 Version 3.1.2 Installation Guide 41

Section	Page
Contents	3
About this Guide	7
Audience	8
Related Documentation	8
Conventions	8
Document Conventions	9
Table 1: Document Conventions	9
Text Symbols	9
Equipment Symbols	10
Rack Stability	11
Getting Help	11
HP Technical Support	11
HP Storage Website	12
HP Authorized Reseller	12
Overview	13
SAN Switch 2/16 Features	14
Firmware	14
Hardware	15
SFP Media Side	16
Figure 1: SFP media side	16
Optical Ports	16
ISL Trunking	17
SFPs	17
Power Supply Side	17
Figure 2: Power supply side	17
Field-Replaceable Units	17
Optional Hardware Kits	18
Table 2: SAN Switch 2/16 Orderable Hardware	18
Installing the SAN Switch 2/16	19
Unpack and Verify Carton Contents	20
Figure 3: Carton contents	21
Table 3: Shipping Carton Contents	22
Installation Guidelines	23
Selecting an Operating Location	23
Cooling Requirements	23
Power Requirements	24
Electrostatic Discharge Precautions	24
Installing the SAN Switch as a Stand-alone Unit	25
Installing the Switch in a Rack Using the SAN Switch Rack Mount Kit	26
Table 4: SAN Switch Rack Mount Kit rails and rail mounting hardware	26
Figure 4: Installing the rear mounting brackets (HP 10000 series or comparable EIA cabinet)	28
Figure 5: Installing the rear mounting brackets (HP System/e rack-left rear upright)	29
Figure 6: Installing the outer rails (HP 10000 series or comparable EIA cabinet)	30
Figure 7: Assembling the outer rails (HP 10000 series or comparable EIA cabinet)	31
Figure 8: Assembling the outer rails (HP System/e cabinet)	32
Figure 9: Assembling the inner rails	33
Figure 10: Assembling the inner rails on a SAN Switch with plenum	34
Figure 11: Installing the switch into a rack (HP 10000 series or comparable EIA cabinet)	35
Figure 12: Installing the switch into a rack (HP System/e cabinet)	36
Connecting AC Power	37
Figure 13: Connecting the power cords	37
Power-On Self Test	38
Checking POST Results	38
Configuring Network Addressing	39
Requirements	39
Setting Network Addresses via a Serial Connection	40
Figure 14: Connecting the Serial cable	40
Connecting the Switch to the LAN	43
Figure 15: Connecting the Ethernet cable	43
Important Information on Setting the Core PID Format	44
How to Check the Current Core PID Format	44
How to Change the Core PID Format	45
Modifying Domain IDs	46
Specifying Custom Status Policies	47
Connecting the Switch to the Fabric	47
Figure 16: Inserting a cable into an SFP	48
Verifying Operation	48
Installing Multiple Switches into an Existing SAN	49
Next Steps	50
Setting QuickLoop Mode on Ports	50
Setting Up Speed Negotiation	50
Cascading Switches	51
Managing the SAN Switch 2/16	53
Interpreting LED Activity	54
Front Panel LEDs	54
Table 5: Front Panel LED Patterns During Normal Operation	55
Rear Panel LEDs	58
Table 6: Rear Panel LED Patterns During Normal Operation	58
Management Overview	60
Optional Management Features	60
Displaying the Optional Feature Licenses	60
Enabling Licensed Features	61
Running Basic Switch Operations Using Telnet	61
Logging in to the Switch	61
Changing the Admin Password and User ID	62
Configuring the IP and Fibre Channel Address	63
Displaying Devices within the Fabric	63
Checking the Firmware Version	64
Setting the Switch Date and Time	64
Displaying Switch Configuration Settings	64
Diagnostic Tests	65
Interpreting POST Results	65
Diagnostic Tests	65
Backing Up the Configuration and Upgrading Firmware	67
Backing Up System Configuration Settings	68
Restoring the System Configuration Settings	69
Upgrading or Restoring the Switch Firmware	69
Downloading Firmware from the HP Website	70
Regulatory Compliance Notices	71
FCC EMC Statement (USA)	71
EMC Statement (Canada)	72
EMC Statement (European Union)	72
Spécification ATI Classe A (France)	72
Germany Noise Declaration	72
VCCI EMC Statement (Japan)	72
Harmonics Conformance (Japan)	73
BSMI EMC Statement (Taiwan)	73
RRL EMC Statement (Korea)	73
Laser Safety	74
Battery Replacement Notice	75
Electrostatic Discharge	77
Grounding Methods	78
Technical Specifications	79
Dimensions	80
Table 7: Physical Specifications	80
Power Supply Specifications	81
Table 8: Power Supply Specifications	81
Environmental Requirements	82
Table 9: Environmental Requirements	82
Memory Specifications	83
Table 10: Cabling Pinouts if Pin 7 is Used	83
Glossary	85
Index	97
A	97
B	97
C	97
D	97
E	98
F	98
G	98
H	98
I	98
L	98
M	98
N	98
O	98
P	98
R	99
S	99
T	99
U	99
V	99
W	99