HP StorageWorks 2/16V HP StorageWorks Fabric OS 5.3.0b Release Notes (AA-RWEYF - Page 23

Denial-of-Service condition affecting X.509 certificates verification (NISCC #729618) due to SSL vulnerability in OpenSSL. FOS 5.3.0 includes new version of OpenSSL that resolves this. Fixed per Fabric OS 5.3.0 Incorrect time in Web Tools Switch Health report. Fixed per Fabric OS 5.3.0 Incorrect F_Port behavior when RX side of the cable is disconnected, while the TX side is still inserted. Fixed per Fabric OS 5.3.0 Installation of PKI certificate is delayed on any switch on which installation is attempted due to timing of the startup function. Fixed per Fabric OS 5.3.0 The last character of config uploaded Banner (via "bannerset" CLI command) will disappear when performing a configupload followed by configdownload. Fixed per Fabric OS 5.3.0 When connected to i10k Director in open mode, an RSCN received from the i10k was not immediately forwarded. Fixed per Fabric OS 5.3.0 When upgrading 4/256 to Fabric OS 5.2.0b from 5.2.0a, both ISL trunk connections to an edge switch connected to FC4-16IP were lost. Found in test lab and due to "lab mode" setting, not accessible to customers. Fixed per Fabric OS 5.3.0 Counter Address_err counting inappropriate data. Fixed per Fabric OS 5.3.0 When assigning IP address to a GE port with no cable connection, the FC4-16IP Blade incorrectly reports back to iSCSI initiator that port is valid. Fixed per Fabric OS 5.3.0 The 4/8 and 4/16 SAN Switches would display "Fan x is not faulty" messages on boot up after upgrade to Fabric OS 5.2.0x, even Fixed per Fabric OS 5.3.0 though fans were ok. Disconnecting Rx end of cable on an L_port and leaving the Tx end unchanged results in unexpected behavior. Fixed per Fabric OS 5.3.0 Access Gateway should handle an IPv6 address in a GMAL payload IP address in "ag - show" truncated to 16 characters (size of IPv4 address) depending on size of IP address string for edge switch to which N_Port attached. Fixed per Fabric OS 5.3.0 Switchdisable and switchenable on switch that directly connects to storage will cause the storage to see GLIEN reject error message. Fixed per Fabric OS 5.3.0 F_Port count is incorrect in agshow on the 4/32 SAN switch. Fixed per Fabric OS 5.3.0 In CLI, iscsicfg -show/delete ddset -n xxx complains "requested object doesn't exist" even though it does exist, due to DD/DDSETs received from Microsoft iSNS server being in uppercase. Fixed per Fabric OS 5.3.0 During iSCSI 1024 session stress testing, one port lost multiple sessions. Even though switchshow -iscsi showed less than 64 sessions, iSCSI initiator wasn't able to log in to the target (out of resources error). Fixed per Fabric OS 5.3.0 Incorrect GID_FT response from NameServer. NameServer assumes device's FC4 type is FCP when GID_FT request is sent to the switch asking for PIDs of type FCP. PID of the sending device is incorrectly included in the reply list. Fixed per Fabric OS 5.3.0 Unable to merge an upgraded switch with a 4/256 with FC4-48 Blade when using domain/port zoning of the upper 32 ports of the Blade. When creating D,P zoning definition using these upper 32 ports on FC4-48 connected to another switch running 5.1.0, the two switches correctly segment due to zoning conflict. After upgrading to 5.2.0, switches remain segmented, but segmentation should be removed. Fixed per Fabric OS 5.3.0 HP StorageWorks Fabric OS 5.3.0b release notes 23