HP StorageWorks 2/32 HP StorageWorks SAN Switch Rack Mount Kit Installation In
HP StorageWorks 2/32 - SAN Switch Manual
View all HP StorageWorks 2/32 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP StorageWorks 2/32 manual content summary:
- HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 1
SAN switch rack mount kit Second Edition (June 2003) Part Number: AV-RU6YB-TE This document provides step-by-step instructions for installing the SAN Switch 2/8, SAN Switch 2/16 or SAN Switch 2/32 using the hp StorageWorks SAN switch rack mount kit. For the latest version of these Installation - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 2
limited warranty statements for such products. Nothing herein should be construed as constituting an additional warranty. Printed in the U.S.A. SAN Switch Rack Mount Kit Installation Instructions Second Edition (June 2003) Part Number: AV-RU6YB-TE 2 SAN Switch Rack Mount Kit Installation - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 3
HP Series 9000 or comparable EIA rack, or in an HP System/e rack using the SAN Switch Rack Mount Kit, part number 331148-B21 who are experienced with the following: ■ HP StorageWorks Fibre Channel SAN switches ■ Fabric following StorageWorks website: http://www.hp.com/country/us/eng/ prodserv/ - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 4
extended at any time. A rack may become unstable if more than one rack component is extended for any reason. 4 SAN Switch Rack Mount Kit Installation Instructions - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 5
) cabinet (like the HP 9000 Series Rack). ■ In an HP System/e rack. Selecting ■ If installing the switch in the HP 9000 Series, or comparable EIA rack: the chassis, next to the HP logo. HP recommends installing the switch so front-to-back direction. Note: HP highly recommends mounting the switch in - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 6
, and maintain ground at all times. Do not rely on a secondary connection to a branch circuit, such as a power strip. 6 SAN Switch Rack Mount Kit Installation Instructions - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 7
and to exhaust at the rear of the rack, similar to other rack-mounted equipment. This prevents switch overheating. SAN Switch Rack Mount Kit Installation Instructions 7 - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 8
section provides instructions for installing the SAN Switch 2/32, SAN Switch 2/16, or SAN Switch 2/8 in an HP System/e rack, or in an HP 9000 Series or comparable EIA rack using the SAN Switch Rack Mount Kit, part number 331148-B21. Figure 1: SAN - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 9
lock washer (8) #10 alignment washer (8) #10 adapter washer (2) 1/4-20 hex nut with captive star lock washer (2) 1/4-inch flat washer SAN Switch Rack Mount Kit Installation Instructions 9 - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 10
brackets to the rear rack uprights by completing one of the following steps: - For an HP 9000 Series or comparable EIA rack, assemble each of the two brackets with (2) #10-32 2: Installing the rear mounting brackets (HP 9000 Series or comparable EIA rack) 10 SAN Switch Rack Mount Kit Installation - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 11
brackets with (2) #10-32 x 1/2-inch Phillips pan-head screws and (2) #10 alignment washers as shown in Figure 3. Figure 3: Installing the rear mounting brackets (HP System/e rack-left rear upright) Note: This kit contains both left rails and right rails. The rails are marked with Right and Left to - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 12
star lock washers attached loosely as shown in Figure 4. Don't tighten them. The nuts will be tightened later in step 8. Figure 4: Installing the outer rails (HP 9000 Series or comparable EIA rack) 12 SAN Switch Rack Mount Kit Installation - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 13
rack you are using, complete one of the following tasks: - For an HP 9000 Series or comparable EIA rack, install two #10-32 x 1/2-inch Phillips rail. See Figure 5. Figure 5: Assembling the outer rails (HP 9000 Series or comparable EIA rack) SAN Switch Rack Mount Kit Installation Instructions 13 - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 14
the upper and lower hole locations of the left rail. See Figure 6. Figure 6: Assembling the outer rails (HP System/e rack) 5. Determine the number of #8-32 x 3/16-inch Phillips pan-head screws with thread lock x 3/16-inch Screws 12 10 14 14 SAN Switch Rack Mount Kit Installation Instructions - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 15
the back of the rack. The rear of the switch, the AC side, faces the front of the rack. SAN Switch Rack Mount Kit Installation Instructions 15 - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 16
, tighten the #8-32 x 3/16-inch Phillips pan-head screw with thread lock and torque between 6 to 8 inch-pounds. 16 SAN Switch Rack Mount Kit Installation Instructions - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 17
, preventing overheating. If the plenum is not preinstalled on the SAN Switch 2/8, refer to the HP StorageWorks SAN Switch 2/8 Version 3.1.x Installation Guide for complete plenum installation instructions. Figure 8: Assembling the inner rails on a SAN Switch 2/8 with plenum SAN Switch Rack Mount - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 18
the switch into a rack (HP 9000 Series or comparable EIA rack) Insert the switch into the rack and install (2) #10-32 x 1/2-inch Phillips pan-head screws with captive star lock washers with one on each side. See Figure 9 and Figure 10. 18 SAN Switch Rack Mount Kit Installation Instructions - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 19
Figure 10: Installing the switch into a rack (HP System/e rack) 8. Tighten the nuts installed in step a of step 4 on page 12. See Figure 4. Note: To uninstall a switch, screw with captive star lock washer from either side of the rack uprights. SAN Switch Rack Mount Kit Installation Instructions 19 - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 20
20 SAN Switch Rack Mount Kit Installation Instructions
installation
instructions
hp
StorageWorks
SAN switch
rack mount kit
Second Edition (June 2003)
Part Number:
AV–RU6YB–TE
This document provides step-by-step
instructions for installing the SAN Switch 2/8, SAN Switch
2/16 or SAN Switch 2/32 using the hp StorageWorks SAN switch rack mount kit.
For the latest version of these Installation Instructions and other documentation, access the HP
storage website at:
.