HP StorageWorks 4/64 Brocade Fabric OS Message Reference Supporting Fabric OS
HP StorageWorks 4/64 - SAN Switch Manual
View all HP StorageWorks 4/64 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP StorageWorks 4/64 manual content summary:
- HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 1
53-1000600-01 19 October 2007 Fabric OS Message Reference Supporting Fabric OS v6.0.0 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 2
http://www.brocade.com/support/oscd. Export of technical data contained in this document may require an export license from the United States Government. Brocade Communications Systems, Incorporated Corporate Headquarters Brocade Communications Systems, Inc. 1745 Technology Drive San Jose, CA - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 3
versions of the Brocade Fabric OS Message Reference support March 2004 Fabric OS System Error Message 53-0000515-09 Updated for v4.4.0, Reference Manual First Manual 1001 Fabric OS System Error Message 53-1000046-01 Added BM, FCR, IPS, FCIP, SEC, and ZONE January 2006 Reference Manual - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 4
-1000046-02 Minor updates to a few messages. Reference Manual June 2006 Fabric OS Message Reference 53-1000242-01 - -Deleted USWD chapter. -Updated Introductory chapters. -Update throughout: rebranding, supported hardware, CLI changes. 15 June 2007 Fabric OS Message Reference 53-1000600- - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 5
8 Audit Event Messages 9 Message Severity Levels 11 Responding to a System Message 11 Looking Up a System Message 11 Gathering Information About the Problem 12 Support 12 Panic Dump and Core Dump Files 12 Trace Dumps 13 supportSave Command 13 Fabric OS Message Reference v 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 6
System Module Descriptions 14 Section I RASLog Messages Section II Audit Log Messages Chapter 2 Chapter 3 AG System Messages AG-1001 25 AG-1002 25 AG-1003 25 AG-1004 26 AG-1005 26 AG-1006 26 AG-1007 26 AG-1008 27 AG-1009 27 AG-1010 27 AG-1011 28 AG-1012 28 AG-1013 28 AG-1014 28 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 7
AUTH-1004 34 AUTH-1005 34 AUTH-1006 34 AUTH-1007 34 AUTH-1008 35 AUTH-1010 35 AUTH-1011 35 AUTH-1012 36 AUTH-1013 36 AUTH-1014 36 AUTH-1016 36 AUTH-1017 37 AUTH-1018 37 AUTH-1020 37 AUTH-1022 38 AUTH-1023 38 AUTH-1025 39 AUTH-1026 39 AUTH-1027 39 AUTH-1028 40 AUTH-1029 40 AUTH- - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 8
Chapter 4 Chapter 5 BKSW System Messages BKSW-1003 47 BL System Messages BL-1000 49 BL-1001 49 BL-1002 49 BL-1003 50 BL-1004 50 BL-1006 50 BL-1007 51 BL-1008 51 BL-1009 51 BL-1010 52 BL-1011 52 BL-1012 53 BL-1013 53 BL-1014 53 BL-1015 54 BL-1016 54 BL-1017 55 BL-1018 55 BL-1019 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 9
60 Chapter 6 BLL System Messages BLL-1000 61 Chapter 7 BM System Messages BM-1001 63 BM-1002 63 BM-1003 63 BM-1004 64 BM-1005 64 BM-1006 64 BM-1007 65 BM-1008 65 BM-1009 65 BM-1010 65 BM-1053 66 BM-1054 66 BM-1055 66 BM-1056 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 10
Chapter 11 CONF System Messages CONF-1000 75 CONF-1001 75 CONF-1020 75 CONF-1021 76 CONF-1022 76 CONF-1030 76 Chapter 12 EM System Messages EM-1001 77 EM-1002 77 EM-1003 77 EM-1004 78 EM-1005 78 EM-1006 79 EM-1007 79 EM-1008 79 EM-1009 80 EM-1010 80 EM-1011 80 EM-1012 81 EM-1013 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 11
EM-1042 87 EM-1043 87 EM-1044 87 EM-1045 88 EM-1046 88 EM-1047 88 EM-1048 89 EM-1049 89 EM-1050 89 EM-1051 89 EM-1055 90 EM-1056 90 EM-1057 90 EM-1058 91 EM-1059 91 EM-1060 91 EM-1061 91 EM-1062 92 EM-1063 92 EM-1064 92 EM-1065 93 EM-1066 93 EM-2003 93 Chapter 13 ESS System - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 12
FABR-1021 105 FABR-1022 106 FABR-1023 106 FABR-1024 106 FABR-1029 107 FABR-1030 107 FABR-1031 107 FABR-1032 108 Chapter 16 FABS System Messages FABS-1001 109 FABS-1002 109 FABS-1004 109 FABS-1005 110 FABS-1006 110 FABS-1007 111 FABS-1008 111 FABS - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 13
FABS-1012 112 FABS-1013 113 FABS-1014 113 FABS-1015 113 Chapter 17 FBC System Messages FBC-1001 115 Chapter 18 FCIP System Messages FCIP-1000 117 FCIP-1001 117 Chapter 19 FCMC System Messages FCMC-1001 119 Chapter 20 FCPD System Messages FCPD-1001 121 FCPD-1002 121 FCPD-1003 121 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 14
FICN-1017 129 FICN-1018 130 FICN-1019 130 FICN-1020 130 FICN-1021 131 FICN-1022 131 FICN-1023 131 FICN-1024 131 FICN-1025 132 FICN-1026 132 FICN-1027 132 FICN-1028 132 FICN-1029 133 FICN-1030 133 FICN-1031 133 FICN-1032 133 FICN-1033 134 FICN-1034 134 FICN-1035 134 FICN-1036 135 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 15
FICN-1054 139 FICN-1055 140 FICN-1056 140 FICN-1057 140 FICN-1058 141 FICN-1059 141 FICN-1060 141 FICN-1061 141 FICN-1062 142 FICN-1063 142 FICN-1064 142 FICN-1065 142 FICN-1066 143 FICN-1067 143 FICN-1068 143 FICN-1069 143 FICN-1070 144 FICN-1071 144 FICN-1072 144 FICN-1073 145 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 16
FICU-1003 151 FICU-1004 152 FICU-1005 152 FICU-1006 152 FICU-1007 153 FICU-1008 153 FICU-1009 153 FICU-1010 154 Chapter 24 FKLB System Messages FKLB-1001 155 Chapter 25 FLOD System Messages FLOD-1001 157 FLOD-1003 157 FLOD-1004 157 FLOD-1005 158 FLOD-1006 158 Chapter 26 FSPF - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 17
FSSM-1004 166 Chapter 29 FW System Messages FW-1001 167 FW-1002 167 FW-1003 168 FW-1004 168 FW-1005 168 FW-1006 169 FW-1007 169 FW-1008 169 FW-1009 170 FW-1010 170 FW-1011 170 FW-1012 171 FW-1033 171 FW-1034 171 FW-1035 172 FW-1036 172 FW-1037 172 FW-1038 173 FW-1039 173 FW- - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 18
FW-1115 178 FW-1116 179 FW-1117 179 FW-1118 180 FW-1119 180 FW-1120 181 FW-1121 181 FW-1122 181 FW-1123 182 FW-1124 182 FW-1125 182 FW-1126 183 FW-1127 183 FW-1128 184 FW-1129 184 FW-1130 184 FW-1131 185 FW-1132 185 FW-1133 185 FW-1134 186 FW-1135 186 FW-1136 186 FW-1137 187 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 19
Fabric OS Message Reference 53-1000600-01 FW-1171 192 FW-1172 192 FW-1173 192 FW-1174 193 FW-1175 193 FW-1176 193 FW-1177 194 FW-1178 194 FW-1179 194 FW-1180 195 FW-1181 195 FW-1182 195 FW-1183 196 FW-1184 196 FW-1185 196 FW-1186 197 FW-1187 197 FW-1188 197 FW-1189 198 FW-1190 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 20
FW-1248 204 FW-1249 205 FW-1250 205 FW-1251 205 FW-1272 206 FW-1273 206 FW-1274 206 FW-1275 207 FW-1296 207 FW-1297 207 FW-1298 208 FW-1299 208 FW-1300 208 FW-1301 209 FW-1302 209 FW-1303 209 FW-1304 210 FW-1305 210 FW-1306 210 FW-1307 211 FW-1308 211 FW-1309 211 FW-1310 212 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 21
Fabric OS Message Reference 53-1000600-01 FW-1325 217 FW-1326 217 FW-1327 217 FW-1328 218 FW-1329 218 FW-1330 218 FW-1331 219 FW-1332 219 FW-1333 219 FW-1334 220 FW-1335 220 FW-1336 220 FW-1337 221 FW-1338 221 FW-1339 222 FW-1340 222 FW-1341 222 FW-1342 223 FW-1343 223 FW-1344 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 22
FW-1362 231 FW-1363 231 FW-1364 232 FW-1365 232 FW-1366 232 FW-1367 233 FW-1368 233 FW-1369 233 FW-1370 234 FW-1371 234 FW-1372 234 FW-1373 235 FW-1374 235 FW-1375 235 FW-1376 236 FW-1377 236 FW-1378 236 FW-1379 237 FW-1400 237 FW-1401 237 FW-1402 238 FW-1403 238 FW-1424 238 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 23
247 HAM-1005 248 HAM-1006 248 Chapter 31 HAMK System Messages HAMK-1001 251 HAMK-1002 251 HAMK-1003 251 HAMK-1004 252 Chapter 32 HIL System Messages HIL-1101 253 HIL-1102 253 HIL-1103 253 HIL-1104 254 HIL-1105 254 HIL-1106 254 HIL-1107 255 HIL - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 24
HIL-1207 257 HIL-1208 257 HIL-1301 258 HIL-1302 258 HIL-1303 258 HIL-1304 258 HIL-1305 259 HIL-1306 259 HIL-1307 259 HIL-1308 259 HIL-1309 260 HIL-1310 260 HIL-1311 260 HIL-1401 260 HIL-1402 261 HIL-1403 261 HIL-1404 261 HIL-1501 261 HIL-1502 262 HIL-1503 262 HIL-1504 262 HIL- - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 25
ICPD-1005 278 ICPD-1006 278 ICPD-1007 278 ICPD-1008 279 Chapter 39 IPAD System Messages IPAD-1000 281 IPAD-1001 281 Chapter 40 IPS System Messages IPS-1001 283 IPS-1002 283 IPS-1003 283 IPS-1004 283 IPS-1005 284 IPS-1006 284 Fabric OS Message Reference xxv 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 26
Chapter 41 ISCS System Messages ISCS-1000 285 Chapter 42 ISNS System Messages ISNS-1001 287 ISNS-1002 287 ISNS-1003 287 ISNS-1004 288 ISNS-1005 288 ISNS-1006 288 ISNS-1008 289 ISNS-1009 289 ISNS-1010 289 ISNS-1011 289 ISNS-1013 290 ISNS-1014 290 Chapter 43 FCR System Messages FCR- - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 27
Fabric OS Message Reference 53-1000600-01 FCR-1022 296 FCR-1023 296 FCR-1024 297 FCR-1025 297 FCR-1026 297 FCR-1027 298 FCR-1028 298 FCR-1029 298 FCR-1030 299 FCR-1031 299 FCR-1032 299 FCR-1033 299 FCR-1034 300 FCR-1035 300 FCR-1036 300 FCR-1037 300 FCR-1038 301 FCR-1039 301 FCR- - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 28
315 LOG-1002 315 LOG-1003 316 Chapter 47 LSDB System Messages LSDB-1001 317 LSDB-1002 317 LSDB-1003 317 LSDB-1004 318 Chapter 48 MFIC System Messages MFIC-1001 319 xxviii Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 29
MFIC-1002 319 MFIC-1003 320 Chapter 49 MPTH System Messages MPTH-1001 321 MPTH-1002 321 MPTH-1003 321 Chapter 50 MQ System Messages MQ-1004 323 Chapter 51 MS System Messages MS-1001 325 MS-1002 325 MS-1003 326 MS-1004 326 MS-1005 327 MS-1006 327 MS-1008 327 MS-1009 328 MS-1021 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 30
Chapter 54 PDM System Messages PDM-1001 335 PDM-1002 335 PDM-1003 335 PDM-1004 336 PDM-1005 336 PDM-1006 336 PDM-1007 336 PDM-1008 337 PDM-1009 337 PDM-1010 337 PDM-1011 338 PDM-1012 338 PDM-1013 338 PDM-1014 338 PDM-1017 339 PDM-1019 339 PDM-1020 339 PDM-1021 339 PDM-1022 340 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 31
Chapter 58 PS System Messages PS-1000 349 PS-1001 349 PS-1002 349 PS-1003 350 PS-1004 350 PS-1005 350 Chapter 59 PSWP System Messages PSWP-1001 351 PSWP-1002 351 PSWP-1003 351 Chapter 60 RAS System Messages RAS-1001 353 RAS-1002 353 RAS-1004 353 RAS-1005 353 RAS-1006 354 RAS-2001 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 32
362 RPCD-1005 362 RPCD-1006 362 RPCD-1007 362 Chapter 63 RTWR System Messages RTWR-1001 363 RTWR-1002 363 RTWR-1003 364 Chapter 64 SAS System Messages SAS-1001 365 Chapter 65 SCN System Messages SCN-1001 367 Chapter 66 SEC System Messages SEC-1001 369 SEC-1002 369 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 33
Fabric OS Message Reference 53-1000600-01 SEC-1032 375 SEC-1033 375 SEC-1034 375 SEC-1035 376 SEC-1036 376 SEC-1037 376 SEC-1038 376 SEC-1040 377 SEC-1041 377 SEC-1042 377 SEC-1043 378 SEC-1044 378 SEC-1045 378 SEC-1046 379 SEC-1049 379 SEC-1050 379 SEC-1051 380 SEC-1052 380 SEC- - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 34
SEC-1079 386 SEC-1080 387 SEC-1081 387 SEC-1082 387 SEC-1083 388 SEC-1084 388 SEC-1085 388 SEC-1086 389 SEC-1087 389 SEC-1088 389 SEC-1089 390 SEC-1090 390 SEC-1091 390 SEC-1092 391 SEC-1093 391 SEC-1094 391 SEC-1095 392 SEC-1096 392 SEC-1097 392 SEC-1098 393 SEC-1099 393 SEC- - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 35
Fabric OS Message Reference 53-1000600-01 SEC-1121 399 SEC-1122 399 SEC-1123 399 SEC-1124 399 SEC-1126 400 SEC-1130 400 SEC-1135 400 SEC-1136 401 SEC-1137 401 SEC-1138 401 SEC-1139 402 SEC-1142 402 SEC-1145 402 SEC-1146 403 SEC-1153 403 SEC-1154 403 SEC-1155 404 SEC-1156 404 SEC- - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 36
SEC-1182 410 SEC-1183 410 SEC-1184 411 SEC-1185 411 SEC-1186 411 SEC-1187 412 SEC-1188 412 SEC-1189 412 SEC-1190 413 SEC-1191 413 SEC-1192 413 SEC-1193 414 SEC-1194 414 SEC-1195 414 SEC-1196 415 SEC-1197 415 SEC-1198 415 SEC-1199 416 SEC-1200 416 SEC-1201 416 SEC-1202 417 SEC- - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 37
SEC-1312 422 SEC-1313 422 SEC-1314 423 SEC-1315 423 SEC-1316 423 SEC-1317 424 SEC-1318 424 SEC-1319 424 SEC-1320 424 SEC-1321 425 SEC-1322 425 SEC-1323 425 SEC-1324 426 SEC-1325 426 SEC-1326 426 SEC-1327 427 SEC-1328 427 SEC-1329 427 SEC-1330 427 SEC-1331 428 Chapter 67 SNMP - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 38
SULB-1003 433 SULB-1004 434 SULB-1005 434 SULB-1006 434 SULB-1007 434 SULB-1008 435 SULB-1009 435 SULB-1010 441 SULB-1011 441 SULB-1017 441 SULB-1018 442 SULB-1020 442 SULB-1021 442 SULB-1022 443 SULB-1023 443 SULB-1024 443 SULB-1025 444 SULB-1026 444 SULB-1030 444 SULB-1031 444 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 39
Chapter 71 SYSC System Messages SYSC-1001 451 SYSC-1002 451 SYSC-1003 452 SYSC-1004 452 SYSC-1005 452 Chapter 72 SYSM System Messages SYSM-1001 453 SYSM-1002 453 SYSM-1003 453 SYSM-1004 454 SYSM-1005 454 SYSM-1006 454 SYSM-1007 454 Chapter 73 TRCE System Messages TRCE-1001 455 TRCE - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 40
Chapter 75 TS System Messages TS-1001 463 TS-1002 463 TS-1006 464 TS-1007 464 TS-1008 465 Chapter 76 UCST System Messages UCST-1003 467 UCST-1007 467 UCST-1020 467 Chapter 77 UPTH System Messages UPTH-1001 469 Chapter 78 WEBD System Messages WEBD-1001 471 WEBD-1002 471 WEBD-1003 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 41
ZONE-1013 480 ZONE-1014 481 ZONE-1015 481 ZONE-1017 481 ZONE-1018 482 ZONE-1019 482 ZONE-1022 483 ZONE-1023 483 ZONE-1024 483 ZONE-1026 484 ZONE-1027 484 ZONE-1028 485 ZONE-1029 485 ZONE-1030 485 ZONE-1031 486 ZONE-1032 486 ZONE-1033 486 ZONE-1034 487 ZONE-1035 487 ZONE-1036 487 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 42
AUTH-3006 492 AUTH-3007 493 AUTH-3008 493 Chapter 82 AUDIT CONF System Messages CONF-1000 495 CONF-1020 495 CONF-1022 495 Chapter 83 AUDIT HTTP System Messages HTTP-1002 497 HTTP-1003 497 Chapter 84 AUDIT SEC System Messages SEC-3001 499 SEC-3002 499 SEC-3003 500 SEC-3004 500 SEC- - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 43
SEC-3025 507 SEC-3026 507 SEC-3027 508 SEC-3028 508 SEC-3029 508 SEC-3030 509 SEC-3031 509 SEC-3032 509 SEC-3033 510 SEC-3034 510 SEC-3035 510 SEC-3036 510 SEC-3037 511 SEC-3038 511 SEC-3039 511 SEC-3044 512 SEC-3045 512 SEC-3046 512 SEC-3047 512 SEC-3048 513 SEC-3049 513 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 44
SULB-1021 525 SULB-1023 525 SULB-1024 526 SULB-1026 526 SULB-1030 526 SULB-1031 527 SULB-1032 527 SULB-1033 527 SULB-1034 527 SULB-1035 528 SULB-1037 528 Chapter 87 AUDIT ZONE System Messages ZONE-3001 529 ZONE-3002 529 ZONE-3003 530 ZONE-3004 530 ZONE-3005 530 ZONE-3006 531 ZONE- - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 45
ZONE-3025 537 Fabric OS Message Reference xlv 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 46
xlvi Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 47
Fabric OS v5.3.0 to 6.0.0, supporting the following platforms: • Brocade 200E, 4012, 4016, 4018, 4020, 4024 switches • Brocade 3250 switch • Brocade 3850 switch • Brocade 3900 switch • Brocade 4100, 4900, 5000, 7500, AP 7600 switches • Brocade 24000 director Fabric OS Message Reference xlvii 53 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 48
• Brocade 48000 director • FA4-16 blade • FC10-6 blade In those instances in which procedures or parts of procedures documented here apply to some switches but not to others, this guide identifies exactly which switches are supported and which are not. Although many different software and hardware - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 49
guide Otherwise, this manual specifically notes to hardware, firmware, software, (SAN)-specific BROCADE RESOURCES The following related documentation is provided on the Brocade Documentation CD-ROM and on the Brocade Web site, through Brocade Connect. NOTE Go to http://www.brocade.com and click Brocade - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 50
problems before they become costly failures. ISL Trunking Brocade® ISL Trunking is an optional software product available for all Brocade 2 and 4 Gbit/sec Fibre Channel switches and directors. This technology is ideal for optimizing performance and simplifying the management of multi-switch SAN - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 51
Service enables Fibre Channel frames to "tunnel" through IP networks by dividing frames, encapsulating the result in IP packets on entering the tunnel, and then reconstructing them as they leave the tunnel. Fabric OS supports eight FCIP interswitch links between two Brocade switches (Brocade - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 52
4012, 4016, 4018, 4020, and 4024 switches: nonport side of chassis. - Brocade 3250, 3850, and 3900 switches: Bottom of chassis. - Brocade 4100, 4900, 5000, 7500, and AP7600 switches: on the pullout tab on the front of the switch. - Brocade 24000, and 48000 directors: Inside the front of the chassis - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 53
guide supports Fabric OS v6.0.0 and documents system messages that can help you diagnose and fix problems with a switch or fabric. The messages are organized first by event type, reliability, availability, and serviceability are saved to nonvolatile storage by default. • The system error message log - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 54
. The sequence number is persistent across power cycles and switch reboots. • By default, the errDump and errShow commands display support post-event audtis and problem determination based on high-frequency events of certain types such as security violations, zoning configuration changes, firmware - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 55
running UNIX, Linux, or any other operating system that supports the standard syslogd functionality. Configuring for syslogd involves configuring the host, enabling syslogd on the Brocade model, and, optionally, setting the facility level. For the Brocade DCX, 24000 and 48000, each CP has a unique - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 56
. When the log is full, the newest log entries overwrite the oldest log entries. Port logs capture switch-to-device, device-to-switch, switch-to-switch, some device A-to-device B, and control information. Port logs are not persistent and are lost over power cycles and reboots. Run the portLogShow - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 57
Resets the SNMP recipients to default values. agtCfgSet Modifies the SNMP POST (Power-On Self-Test) configuration. errClear Clears all error log messages for all switch instances on Fabric OS. supportFtp Sets, clears, or displays support FTP parameters or a time interval to check the FTP - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 58
switch service provider to diagnose and correct problems with the switch. The output from this command is very long. syslogDIpAdd Adds an IP is a reference to the blade within the switch platform, e.g.,Brocade 7500 and AP7600 contain FR4-18i and FA4-18 blades respectively. traceDump Displays, - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 59
speed. Type to continue, Q to stop: CLEARING THE SYSTEM MESSAGE LOG To clear the system message log for a particular switch instance: 1. Log in to the switch as admin. 2. Use the errClear command to clear all messages from memory. NOTE For products that have a single processor, all error - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 60
4-FIRMWARE 5-FABRIC 3. Enable the audit feature: switch:admin switch to point to the configured servers' IP addresses. switch:admin> syslogdipadd 10.128.128.160 6. Verify the switch's syslog configuration: switch switch. The RASLog subsystem will support an internationalized timestamp format base - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 61
command. The sequence number is persistent across power cycles and switch reboots. For most messages, this field problem determination. Audit event message format: AUDIT, , [], , , ////. / - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 62
UTC) when the message was generated on the switch. The RASLog subsystem will support an internationalized timestamp format base on the "LOCAL" setting. Message Module Firmware Fabric User ID Identifies the user ID. Role Identifies the role of the user ID. IP Address Identifies the IP address - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 63
to be used as general guidelines for troubleshooting. For all cases, you should look at longer operating in redundant mode unless the failed power supply is replaced or fixed. Info-level messages Message 11 • Gathering Information About the Problem 12 • Support 12 • Panic Dump and Core Dump - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 64
Run the errDump command on each logical switch. 6. Run supportFtp (as needed) to Brocade DCX, 12000, 24000, or 48000) 13. What and when were the last actions or changes made to the system? SUPPORT Fabric OS create a number of files that can help support personnel troubleshoot and diagnose a problem - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 65
with the exception of the Fabric Watch daemon and the IP storage demon, which ping the SWD every 333 seconds. for support personnel use only. TRACE DUMPS The Fabric OS produces trace dumps when problems output of the supportShow command to an off-switch storage location via FTP. Prior to running - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 66
hardware platforms. Blade management error messages are a result of autoleveling firmware upgrades performed by the control processor (CP). Condor application specific integrated circuit (ASIC) driver error messages. This is the core edge routing module on the Brocade director platforms. Status - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 67
of the switch nondisruptively during failures and software upgrades. These service. A component is a module in the Fabric OS, implementing a related set of functionality. A service BP. System messages generated by the IP admin demon. Fibre Channel over IP license, tunneling, and port related messages - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 68
(agd) • Alias Server (asd) • ARR daemon (arrd) • Authentication daemon (authd) • Blade Manager (bmd) • Common Access Layer (cald) • Diagnostics daemon (diagd) • Environment Monitor (emd) • EVM daemon (evmd) • Exchange Service Support daemon (essd) • FA-API rpc daemon (rpcd) • Fabric daemon (fabricd - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 69
an "unreachable" message to the caller, allowing the caller to take the appropriate action. If a switch is not responding, RTWR retries 100 times. Storage application services supporting director-class storage virtualization platform. The internal state change notification daemon is used for state - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 70
any problems associated with the zoning features, including commands associated with aliases, zones, and configurations. NOTE Any reference seen in a system message to slot 0 is a reference to the blade within the switch platform, for example: Brocade DCC contain FC8-48, FC9-32, and FC8-16 blades - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 71
RASLog Messages This section provides the RASLog messages, including: • AG System Messages 25 • AUTH System Messages 33 • BKSW System Messages 47 • BL System Messages 49 • BLL System Messages 61 • BM System Messages 63 • C2 System Messages 69 • CDR System Messages 71 • CER System Messages - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 72
269 • HTTP System Messages 271 • IBD System Messages 273 • IBPD System Messages 275 • ICPD System Messages 277 • IPAD System Messages 281 • IPS System Messages 283 • ISCS System Messages 285 • ISNS System Messages 287 • KSWD System Messages 311 • KTRC System Messages 313 • LOG System - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 73
• TRCK System Messages 461 • TS System Messages 463 • UCST System Messages 467 • UPTH System Messages 469 • WEBD System Messages 471 • ZOLB System Messages 475 • ZONE System Messages 477 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 74
- HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 75
Audit Log Messages This section provides the Audit messages, including: • AUDIT AUTH System Messages 491 • AUDIT CONF System Messages 495 • AUDIT HTTP System Messages 497 • AUDIT SEC System Messages 499 • AUDIT SNMP System Messages 515 • AUDIT SULB System Messages 517 • AUDIT ZONE System - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 76
- HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 77
blades and ports in a switch may not support NPIV. NPIV functionality cannot be enabled on such ports and they will not respond to NPIV requests. Refer to the Access Gateway Administrator Guide, Appendix B for specific AG compatibility requirements. • On non-Brocade switches your switch service - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 78
message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity ERROR AG-1005 Message , [AG-1005], ,, WARNING, , FDISC response was dropped because F_Port - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 79
the message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity WARNING AG-1009 Message , [AG-1009], ,, WARNING, , Sending FLOGI failed on N_Port - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 80
the message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity WARNING AG-1013 Message , [AG-1013], ,, INFO, , F_Ports mapped to N_Port failed - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 81
the message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity WARNING AG-1016 Message , [AG-1016], ,, INFO, , Failing over F_Ports mapped to N_Port - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 82
: is online. Probable Cause Failover across port groups is not supported. Recommended Please check whether or not an alternate N_Port is configured in Cause Indicates that F_Ports to N_Ports mapping has been changed because the switch has come online or some new N_Port/F_Port has come online. - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 83
AG-1023 2 Probable Cause Indicates that the specified F_Port is failing over to its preferred N_Port. Recommended Please run ag --mapshow to display the updated F_Port to N_Port mapping. Action Severity INFO AG-1023 Message , [AG-1023], ,, INFO, , F_Port - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 84
2 32 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 85
Retry the secAuthSecret command. Run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity ERROR AUTH-1003 Message , [AUTH-1003], ,, INFO, , type has been - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 86
firmware. Run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service protocol(s) are not supported: port . Indicates that the proposed authentication protocol type or types are not supported by the local specified - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 87
sure the local switch supports the specified protocols: problem with the Secure Fabric OS. Recommended Action Reboot or power cycle the switch. If the message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 88
support authentication. Recommended Make sure the entity at the other end of the link supports Recommended Action Usually this problem is transient. The authentication ; then run the supportSave command and contact your switch service provider. Severity WARNING AUTH-1014 Message , - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 89
your Action switch service provider. Severity ERROR AUTH-1017 Message , [AUTH-1017], ,, ERROR, , Invalid value to start authentication request: port , operation code . Probable Cause Indicates an internal problem with the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 90
set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity INFO AUTH-1022 Message , [AUTH-1022], - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 91
run the supportSave command and contact your switch service provider. Severity ERROR AUTH-1026 Message Recommended Action Usually this problem is transient. If switch does not support the specified authentication value. Recommended Check the authentication configuration and reset the supported - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 92
up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity ERROR AUTH-1028 Message , [AUTH-1028], < failed to get memory. Recommended Action Usually this problem is transient. The authentication might fail. Reinitialize - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 93
prevent replay attacks. Recommended Action Usually this problem is transient. The authentication might fail. Reinitialize up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity ERROR AUTH-1033 Message , [AUTH-1033], - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 94
up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity ERROR AUTH-1035 Message , [AUTH-1035], - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 95
message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity ERROR AUTH-1037 Message , [AUTH-1037], ,, ERROR, , Failed to response for - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 96
message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity ERROR AUTH-1042 Message Probable Cause , [AUTH-1042], ,, ERROR, , Port has - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 97
your switch service provider. defaulted to OFF, and switch will not participate in Diffie Hellman - challenge handshake authentication protocol (DH-CHAP) authentication with devices. Recommended Try setting the device authentication policy manually a result. This problem may be transient due - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 98
3 AUTH-1044 46 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 99
is found, run supportFtp to send all core files to a secure server location. Copy the error message and any core file information, and contact your switch service provider. Severity WARNING Fabric OS Message Reference 47 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 100
4 BKSW-1003 48 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 101
correctly. If the blade is seated correctly, reboot or power cycle the blade. Run the systemVerification command to verify that the blade does not have hardware problems. Note that any reference seen to slot 0 is a reference to the blade within the switch platform, e.g.,Brocade 7500 and AP7600 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 102
Recommended Action Make sure that the blade is seated correctly. If the blade is seated correctly, reboot or power cycle the blade. Run the systemVerification command to verify that blade does not have hardware problems. Run the diagPost command to ensure that Power-On Self-Test (POST) is enabled - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 103
. Recommended Action Make sure that the blade is seated correctly. If the blade is seated correctly, reboot or power cycle the blade. Run the systemVerification command to verify that the blade does not have hardware problems. Run the diagPost command to ensure that Power-On Self-Test (POST) is - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 104
to verify that the blade or switch does not have hardware problems. Run the diagPost command to ensure that Power-On Self-Test (POST) is enabled. On a bladed switch, run the slotPowerOff and slotPowerOn commands. On a nonbladed switch, reboot or power cycle the switch. If the message persists - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 105
pluggable (SFP), or device attached to the specified port. On a bladed switch, run the slotPowerOff and slotPowerOn commands. On a nonbladed switch, reboot or power cycle the switch. If the message persists, replace the blade. Severity ERROR BL-1014 Message Probable Cause , [BL-1014 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 106
the diagPost command to ensure that Power-On Self-Test (POST) is enabled. If there is a hardware error, if the slotPowerOff or slotPowerOn fails on the bladed switch or if errors are encountered again: • On the Brocade DCX, 24000, and 48000, replace the blade field-replaceable unit (FRU). • On the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 107
5 Recommended Action Make sure that the blade is seated correctly. If the blade is seated correctly, reboot or power cycle the blade. Run the systemVerification command to verify that the blade does not have hardware problems. Run the diagPost command to ensure that Power-On Self-Test (POST) is - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 108
application-specific integrated circuit (ASIC) chips. Recommended Action Reboot or power cycle the switch. Run the systemVerification command to verify that the switch does not have hardware problems. Run the diagPost command to ensure that Power-On Self-Test (POST) is enabled. Refer to the Fabric - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 109
firmware upgrade. Probable Cause Indicates that a recent firmware upgrade caused the blade's firmware to be upgraded and resulted in the cold upgrade. As part of the upgrade, all GigE/Fibre Channel over IP warm recovery of the switch.The switch will reboot and start a cold recovery. Fabric - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 110
power cycle the switch. If the message persists, replace the switch. Severity CRITICAL BL-1029 Message , [BL-1029], ,, INFO, , All ports on the switch will be reset as part of the firmware upgrade. Probable Cause Indicates that a recent firmware upgrade - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 111
be reset as part of the firmware upgrade. Probable Cause Indicates that a recent firmware upgrade caused the switch's internal processor firmware to be upgraded and resulted in the cold upgrade. As part of the upgrade, all the GigE/Fibre Channel over IP (FCIP)/Virtualization data elements / FC - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 112
the user ports after disabling the ports. Recommended Action Reboot or power cycle the blade. Run the systemVerification command to verify that the blade does not have hardware problems. Run the diagPost command to ensure that Power-On Self-Test (POST) is enabled. If the message persists, replace - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 113
• 14 = Interrupt suspended • 15 = Filter LISTD error • 16 = Unknown filter LIST error • 17 = Wait for LPC open blade is seated correctly. If the blade is seated correctly, reboot or power cycle the blade. Run the systemVerification command to verify that the blade does not have hardware problems - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 114
6 BLL-1000 If the message persists, replace the blade. Severity CRITICAL 62 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 115
. This can be due to one of the following: • The CP blade is running a later version than the AP blade. • The CP blade is running a much older version than the AP blade. Recommended Action The problem can be corrected by changing the firmware version on either the control processor (CP) or on the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 116
in the specified slot. Recommended Use the slotPowerOff and slotPowerOn commands or reseat the affected blade. On the Brocade Action DCX, 7500 or 7600, switch off and on all primary power in order to power-cycle the unit. Severity WARNING BM-1006 Message , [BM-1006], - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 117
blade firmware failed for blade in slot . Reissue firmwaredownload to recover. Probable Cause The automatic firmware upgrade on the blade has failed because the blade firmware the affected blade. On the Brocade Action 7500 or 7600, switch off and on all primary power in order to power-cycle - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 118
On the Brocade 7500 or 7600, switch off and on all primary power to power-cycle the unit. Action Severity WARNING BM-1054 Message , [BM-1054], ,, INFO, , AP firmware is not consistent with system firmware . Auto-leveling - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 119
>, [BM-1058], ,, WARNING, , Download of AP firmware failed for the switch. Reissue firmwaredownload to recover. Probable Cause The automatic firmware upgrade on the application processor (AP) has failed because the firmware version running on the AP was detected to be - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 120
7 BM-1058 68 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 121
speed may not be supported by the SFP). Please blade/switch will be disrupted. Recommended For a bladed system, perform slotpoweroff and slotpoweron on the blade to recover the system. For Action a non-bladed system, perform fastboot on the switch problem Action persists, replace the blade. Severity - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 122
>, Rate limit configuration is not effective on S() user port because QoS license is not present. Probable Cause Indicates that the switch does not have the QoS license added. Rate Limit is a licensed feature and requires QoS license. Recommended Add QoS license to the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 123
a bladed system, issue the slotPowerOff and slotPowerOn commands on the blade to recover Action the system. For a non-bladed system, perform fastBoot on the switch to at the next maintenance window. If the problem Action persists, replace the blade. Fabric OS Message Reference 71 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 124
specific integrated circuit (ASIC) hardware that may degrade data traffic. Recommended Whenever this error occurs, reboot the system at the next maintenance window. If the problem Action persists, replace the blade. Severity ERROR 72 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 125
loaded on the standby CP. The standby CP does not support the Advanced Performance Tuning module when the fibre connectivity (FICON) Management Server is enabled. Recommended Action Run the firmwareDownload command to upgrade the firmware on the standby CP. You can also disable FMS on the active - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 126
10 CER-1001 74 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 127
Chapter CONF System Messages 11 CONF-1000 Message , [CONF-1000], , AUDIT, INFO, , configDownload completed successfully. . Probable Cause Indicates that the configDownload operation was initiated and completed - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 128
more parameters that require the switch to be disabled. Recommended Disable the switch and try to download configuration again. Action Severity INFO CONF-1030 Message , [CONF-1030], ,, WARNING, , Configuration database full, data not committed (key: - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 129
faulted. Probable Cause Indicates that a field-replaceable unit (FRU) header could not be read or is not valid. The FRU is faulted. Recommended Action On Brocade 24000 and 48000, try reseating the specified FRU. Reboot or power cycle the switch. Fabric OS Message Reference 77 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 130
an optional number to identify the unit, slot, or port. The Brocade 3250 has one power supply and three fans, and the Brocade 3850 has two power supplies and four fans. Values for the individual fans and power supplies for these switches might display, but these parts cannot be replaced: the entire - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 131
the faulty slot or the switch for nonbladed switches. Recommended Action There is most likely a voltage hardware problem on the blade or motherboard of the switch. For the Brocade DCX, 24000 and 48000, replace the blade field-replaceable unit (FRU). For the Brocade 3900 replace the motherboard FRU - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 132
Try reseating the FRU. If the message persists, replace the FRU. Refer to the Brocade 48000 Hardware Reference Manual for more information about chassisConfig modes and supported blades. Severity CRITICAL EM-1010 Message , [EM-1010], , FFDC, CRITICAL, - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 133
serious internal Fabric OS configuration or hardware problems on the switch. Recommended Action On Brocade DCX, 24000 and 48000, try reseating the indicated field-replaceable unit (FRU). If the message persists, reboot or power cycle the switch. Run the systemVerification command to verify that - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 134
Recommended Monitor the switch. If the problem persists, a reBoot or power cycle is required to resolve the Action problem. Severity WARNING EM FTP transfers; then run the supportSave command and contact your switch service provider. Severity WARNING EM-1017 Message , [EM-1017 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 135
processor (CP) blade is operational and not supported by the firmware on command, or upgrade the Action firmware on the only. This is a serious hardware problem. The FRU ID value is power cycle the switch. If the message still persists, replace the WWN card, or the switch (for nonbladed switches - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 136
is being retried. Probable Cause Indicates that the I2C bus had problems and a timeout occurred. Recommended Action This is often a 48 port blade) if the field-replaceable unit (FRU) is intended for use. Refer to the appropriate hardware manual for instructions on inserting the switch blades - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 137
problems. Refer to the Fabric OS Command Reference for more information on this command. If the message persists, replace the FRU. Severity ERROR EM-1035 Message , [EM-1035], ,, ERROR, , 2 circuit paired Power Supplies are faulty, please check the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 138
-wide name (WWN) card, then default WWN and IP addresses are used for the switch. Recommended Action Reseat the FRU card. If the message persists, reboot or power cycle the switch. Run the systemVerification command to verify that the switch does not have hardware problems. Refer to the Fabric OS - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 139
responding to commands and should be replaced. Action Severity WARNING EM-1044 Message , [EM-1044], ,, WARNING, , Can't power on , its logical switch is shut down Probable Cause Indicates that the specified field-replaceable unit (FRU) cannot be - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 140
is indicating a predicted failure. If new_state is Down (not enough power), a newly inserted port blade was not powered on because there was not enough power available. Recommended The Brocade 24000 requires only a single power supply for a fully populated chassis; however, you Action should always - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 141
access to the field-replaceable unit (FRU) has become available again. Recommended The EM-1029 error can be a transitory error; if the problem resolves, the EM-1048 message is Action displayed. Severity INFO EM-1049 Message , [EM-1049], ,, INFO, , FRU - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 142
, move it to a port that can support the heat generated. Severity WARNING EM-1056 Message This message is valid for only the Brocade 4100, 4900, 5000, 7500, switch does not reach the reset threshold for the switch/blade. If the reset threshold is reached on the switch/blade, the switch/blade - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 143
the switch does not reach the reset threshold for the switch/blade. If the reset threshold is reached on the switch/blade, the switch/blade will Remove all blades of type or upgrade your standby CP, then reboot or run haSyncStart. A blade in the system is not supported by the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 144
Fault reason>. Probable Cause The blade is power off since a hardware (HW) application specific integrated circuit (ASIC) ERROR was detected, and the user has selected to power off the problem blade when such a condition occurred. Recommended Contact support. Action Severity CRITICAL 92 Fabric - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 145
version of either the control processor firmware (CFOS) or the blade processor firmware (BFOS) is not compatible with the Storage Application Services (SAS) or other application firmware version(s). Recommended Upgrade the FOS firmware or the SAS firmware with the firmwareDownload command. Refer to - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 146
12 EM-2003 94 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 147
Action Discontinue the firmware download, identify the downlevel switch or switches that do not support the Coordinated HotCode protocol, and upgrade the downlevel switches. Then, restart the firmware download on this switch. Note that upgrading a downlevel Brocade switch in a mixed interop - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 148
. Probable Cause During the Coordinated HotCode protocol, a switch in the fabric did not accept the resume message which prevented the protocol from completing. Any data traffic disruption observed during the firmware download may have been due to this issue. Recommended No action - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 149
id.> Probable Cause The event could not be sent to the remote proxy because the remote proxy switch cannot be reached through in-band. Recommended Please make sure that the specified remote domain is present in the fabric. Action Severity WARNING Fabric OS - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 150
14 EVMD-1001 98 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 151
Cause Indicates that an internal link service (ILS) information unit of invalid size has been received. The neighbor switch has sent an invalid sized payload. Recommended Action Investigate the neighbor switch for problems. Run the errShow command on the neighbor switch to view the error log for - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 152
FTP transfers; then run the supportSave command and contact your switch service provider. Severity WARNING FABR-1004 Message , [FABR-1004 incoming data, the system will discard the frame. If it is due to problems with the kernel, the system will recover by performing a failover. If the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 153
automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity WARNING FABR-1007 Message , [FABR-1007], information unit. This message is rare and usually indicates a problem with the Fabric OS. Recommended Action In case of severe - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 154
message is rare and usually indicates a problem with the Fabric OS. Recommended If the message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the Action supportSave command and contact your switch service provider. Severity WARNING FABR-1011 Message - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 155
usually indicates a problem with the Fabric OS. Recommended Action The system will recover by failing over to the standby CP. If the message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 156
>, [FABR-1016], ,, WARNING, , ficonMode is enabled. Probable Cause Indicates that FICON mode is enabled on the switch through a user interface command. Recommended No action is required. Action Severity WARNING FABR-1017 Message , [FABR-1017], - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 157
domains>) exceeds supported configuration (). Probable Cause Indicates that this switch is a value-line switch and has be changed to within the licensed limit. Contact your switch provider to obtain a full fabric license. Severity CRITICAL FABR-1021 Message - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 158
changed to within the licensed limit. Contact your switch provider to obtain a full fabric license. Severity CRITICAL FABR-1023 Message , [FABR-1023], ,, INFO, , Fabric size is within supported configuration (). Fabric limit timer ( - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 159
. In both of the previous modes, the buffer credits are fixed, based on the port configuration information. In this mode, the buffer credits are that fabric exhausted the maximum number of retries sending internal link service (ILS) to the iswitchd demon on the specified E_port. Recommended - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 160
>running an unsupported FOS version v2.x has joined the fabric. Probable Cause Indicates that a switch with an unsupported Fabric OS version 2.x has joined the fabric. Recommended Remove the switch with the unsupported Fabric OS version 2.x from the fabric. Action 108 Fabric OS Message Reference - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 161
Chapter FABS System Messages 16 FABS-1001 Message , [FABS-1001], , FFDC, CRITICAL Fabric OS problem or file corruption. Recommended Action Reboot or power cycle the switch. If the message persists, run the firmwareDownload command to update the firmware. Severity - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 162
which could be any whole number. Recommended Action Reboot or power cycle the active CP (for modular systems) or the switch (for single-board systems). If the message persists, run the firmwareDownload command to update the firmware. Severity WARNING FABS-1006 Message , [FABS-1006 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 163
16 FABS-1007 FABS-1007 Message , [FABS-1007], ,, WARNING, < internal Fabric OS problem or file corruption. Recommended Action Reboot or power cycle the switch. If the message persists, run the firmwareDownload command to update the firmware. Severity WARNING FABS - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 164
an unknown event type. This is usually an internal Fabric OS problem or file corruption. Recommended Action Reboot or power cycle the switch. If the message persists, run the firmwareDownload command to update the firmware. Severity WARNING FABS-1011 Message , [FABS-1011], - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 165
enabled. This is usually an internal Fabric OS problem. Recommended Action Try removing and reinserting the FRU. Reboot or power-cycle the CP or system. If the message persists, run the firmwareDownload command to update the firmware. Severity ERROR Fabric OS Message Reference 113 53-1000600 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 166
16 FABS-1015 114 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 167
Action The problem can be corrected by changing the version of firmware on the CP or AP blades. The firmware version on the CP blade can be changed using the firmwareDownload command. Refer to the release notes to determine whether a non-disruptive firmwareDownload is supported between the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 168
17 FBC-1001 116 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 169
Test Name> failed; algo= type= slot=. Probable Cause Indicates that the FIPS failure has occured and requires faulting the blade/switch. Recommended Run the command again. Action Severity ERROR Fabric OS Message Reference 117 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 170
18 FCIP-1001 118 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 171
is low on memory and failed to allocate new memory for an information unit (IU). Recommended A nonbladed switch will automatically reboot. For a bladed switch, the active CP blade will Action automatically fail over and the standby CP will become the active CP. Severity CRITICAL Fabric OS Message - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 172
19 FCMC-1001 120 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 173
a defect. Action Check with the device vendor for a firmware upgrade containing a defect fix. Severity WARNING FCPD-1002 Message < supported in this port type Probable Cause Private devices will not respond to the switch port login (PLOGI) during probing. Recommended Action The Brocade - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 174
20 FCPD-1003 122 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 175
function call is "kmalloc_wrapper failed". This function call is for kernel memory allocation. Recommended A nonbladed switch will automatically reboot. For a bladed switch, the active CP blade will Action automatically fail over, and the standby CP will become the active CP. Severity CRITICAL - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 176
21 FCPH-1001 124 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 177
: This is a 1 byte hexidecimal value that represents the domain of the switch that the FICON Channel is directly connected to. HP - Host Port number: This is a 1 byte hexidecimal value that represents the switch port of the switch that the FICON Channel is directly connected to. DD - Device Domain - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 178
Disabled> RdBlkId . Probable Cause User changed the configuration manually. Recommended No action is required. Action Severity INFO FICN-1006 Message , [FICN-1006], ,, WARNING, - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 179
as a part of path recovery. Recommended If there was a job failure associated with this event, please contact your vendor's customer support Action for assistance. Severity ERROR FICN-1009 Message , [FICN-1009], ,, INFO, , DevIng:CmdReject Sense Data - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 180
FICON Channel. Recommended If there was a job or IO failure associated with this event, please contact your vendor's customer Action support for assistance. Severity INFO FICN-1011 Message , [FICN-1011], ,, ERROR, , DevDiskIng:XRC Incorrect RRS SeqNum - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 181
22 FICN-1014 Recommended If there was a job or IO failure associated with this event, please contact your vendor's customer Action support for assistance. Severity INFO FICN-1014 Message , [FICN-1014], ,, INFO, , DevEgr:Device level exception flag found - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 182
FICON Control Unit sent a frame that cannot be associated with a FICON Control Unit CUADDR. Recommended Please contact your vendor's customer support for assistance. Action Severity ERROR FICN-1019 Message , [FICN-1019], ,, ERROR, , DevTapeEgr:AS Link - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 183
in emulation. Recommended If there was an unexpected job failure associated with this event, please contact your vendor's Action customer support for assistance. Severity ERROR FICN-1022 Message , [FICN-1022], ,, ERROR, , DevTapeEgr:FICON Selective Reset - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 184
Recommended If there was an unexpected job failure or IO Error associated with this event, please contact your Action vendor's customer support for assistance. Severity ERROR FICN-1025 Message , [FICN-1025], ,, ERROR, , DevTapeIng:Auto Sense Data received - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 185
If there was an unexpected job failure or IO Error associated with this event, please contact your Action vendor's customer support for assistance. Severity ERROR FICN-1031 Message , [FICN-1031], ,, WARNING, , HostDiskIng:FICON System Reset received - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 186
This indicates that the channel side noted corruption from the device/CU side processing. Recommended Please contact your vendor's customer support for assistance. Action Severity ERROR FICN-1035 Message , [FICN-1035], ,, WARNING, , HostIng:FICON System - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 187
connected FICON channel sent a frame that could not be associated with a FICON device. Recommended Please contact your vendor's customer support for assistance. Action Severity ERROR FICN-1039 Message , [FICN-1039], ,, ERROR, , HostIng:FCUB Lookup - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 188
. Recommended If there was an unexpected job failure or IO Error associated with this event, please contact your Action vendor's customer support for assistance. Severity ERROR FICN-1041 Message , [FICN-1041], ,, ERROR, , HostTapeEgr:AS Link Level Reject - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 189
CU or network errors can cause Selective Reset. Recommended If this was an unexpected event, please contact your vendor's customer support for assistance. Action Severity ERROR FICN-1044 Message , [FICN-1044], ,, ERROR, , HostTapeIng:FICON Selective Reset - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 190
an internal emulation error and should not be encountered. Recommended This is an unexpected event, please contact your vendor's customer support for assistance. Action Severity ERROR FICN-1048 Message , [FICN-1048], ,, WARNING, , DevDiskEgr:FICON Cancel - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 191
to break an XRC session with the extended DASD device. Recommended If this was an unexpected event, please contact your vendor's customer support for assistance. Action Severity INFO FICN-1053 Message , [FICN-1053], ,, INFO, , XRC Withdraw From Session - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 192
break an XRC session with the extended DASD device. Recommended If this was an unexpected event, please contact your vendor's customer support for assistance. Action Severity WARNING FICN-1055 Message , [FICN-1055], ,, WARNING, , XRC All Devices Suspended - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 193
could not be created and sent to an LPAR. Recommended This is an unexpected event, please contact your vendor's customer support for assistance. Action Severity ERROR FICN-1060 Message , [FICN-1060], ,, ERROR, , Error return from fcFwdPrcEgressFrame - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 194
an exchange. Recommended If there were associated IO errors at the same time as this event, please contact your vendor's Action customer support for assistance. Severity INFO FICN-1065 Message Probable Cause , [FICN-1065], ,, INFO, , Egress Abort:Oxid=0x - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 195
CH exchange. Recommended If there were associated IO errors at the same time as this event, please contact your vendor's Action customer support for assistance. Severity ERROR FICN-1068 Message , [FICN-1068], ,, ERROR, , Ingress Abort:Oxid=0x - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 196
and not the unit check. If there are associated Action IO error messages with this event, please contact your vendor's customer support for assistance. Severity INFO FICN-1071 Message , [FICN-1071], ,, INFO, , HostTapeIngr:Tape Loaded on Path= - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 197
commands received from the channel for this device>:status=0x:flags=0x. Probable Cause A Rewind and Unload IO has been processed from a locally connected LPAR, which indicates that a tape should be unloaded on a device - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 198
received from the channel for this device>:status=0x:flags=0x. Probable Cause A Rewind and Unload IO has been processed from a remotely connected LPAR, which indicates that a tape should be unloaded on a device - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 199
channel indicates that the channel does not have a path established to the CU. Recommended This is normally an unexpected event, please contact your vendor's customer support for Action assistance. Severity WARNING Fabric OS Message Reference 147 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 200
attached port which had an FICON emulated path established has logged out from the switch. Recommended This may be an unexpected event, please contact your vendor's customer support for assistance. Action Severity WARNING FICN-1083 Message , [FICN-1083], ,, WARNING - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 201
>,tunnel Id=. Probable Cause A FICON FCIP tunnel has been terminated to the peer switch. Recommended If this is an unexpected event, please contact your vendor's customer support for assistance. Action Severity ERROR Fabric OS Message Reference 149 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 202
22 FICN-1086 150 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 203
switch if it has redundant control processors (CPs) or reboot the switch. Run the supportShow command to check if your flash is full. If the flash is full a bladed switch, execute the haFailover command. If the problem persists, or if this is a nonbladed switch, download a new firmware version - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 204
fmsmode using the ficonCupSet command. Refer to the Fabric OS Administrator's Guide for information on core PID mode and the Fabric OS Command Reference unit port (FICON-CUP) daemon failed. Recommended Download a new firmware version using the firmwareDownload command. Refer to the Fabric OS Action - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 205
problem. Recommended Action If the message persists, check the memory usage on the switch, run the supportSave command and contact your switch service provider. Severity WARNING FICU-1008 Message perfDelFilterMonitor command to delete the filter-based performance monitors used on all Action - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 206
23 FICU-1010 FICU-1010 Message , [FICU-1010], ,, WARNING, , FMS Mode enable failed due to address conflict with port . Probable Cause Indicates that the fibre connectivity FICON Management Server mode (fmsMode) was not enabled because the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 207
Chapter FKLB System Messages 24 FKLB-1001 Message , [FKLB-1001], ,, WARNING, , exchange overlapped, pid= Probable Cause Indicates that the FC kernel driver has timed out the exchange while the application is still active. When the FC kernel - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 208
24 FKLB-1001 156 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 209
>, [FLOD-1004], , FFDC, ERROR, , Excessive LSU length = Probable Cause Indicates that the LSU size exceeds what the system can support. Recommended Reduce the number of switches in the fabric or reduce the number of redundant ISLs between two Action - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 210
25 FLOD-1005 FLOD-1005 Message , [FLOD-1005], ,, WARNING, , Invalid received domain ID: Probable Cause Indicates that the received LSR contained an invalid domain number. Recommended No action is required; the LSR is discarded. Action - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 211
number> out of range Probable Cause Indicates that the specified input port number is out of range; it does not exist on the switch. Recommended No action is required. Action Severity ERROR FSPF-1002 Message , [FSPF-1002], ,, INFO, , Wrong neighbor ID - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 212
ID. It should be set to 0 for a nonhierarchical fabric. Brocade switches support only section ID 0. Recommended Action Use a frame analyzer to verify the firmwareDownload command to update the firmware to the latest version. All current versions of the Fabric OS support FSPF version 2, which is - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 213
persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity WARNING FSS-1002 Message , [FSS-1002], ,, WARNING, , Component () sending too - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 214
If the message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity ERROR FSS-1005 Message , [FSS-1005], ,, WARNING, , FSS read failure Probable Cause - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 215
eth1 (as root) or run supportShow/supportSave to validate the network configuration; then try to restore the synchronization by issuing the haSyncStart command. If the problem persists, contact your switch service provider. Severity CRITICAL Fabric OS Message Reference 163 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 216
27 FSS-1007 164 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 217
not become synchronized, run the haDump command to diagnose the problem. If the problem persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity WARNING Fabric OS Message Reference 165 53-1000600 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 218
fails, the failover will be disruptive. In a non-bladed system, this message is logged when the firmware upgrade/downgrade was invoked. The new firmware version is not compatible with current running version. This cause a disruptive firmware upgrade/downgrade. Recommended For a dual CP system, run - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 219
means that the fans and airflow of a switch are functioning normally. Verify that the location temperature is within the operational range of the switch. Refer to the hardware reference manual for the environmental temperature range of your switch. Severity WARNING Fabric OS Message Reference 167 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 220
> . Probable Cause Indicates that the internal temperature of the switch has changed from a value outside of the acceptable range to a that the speed of the fan has changed. Fan problems typically contribute to temperature problems. Recommended Action No action is required. Respond to this - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 221
is . Probable Cause Indicates that the speed of the fan has fallen below the low boundary. Fan problems typically contribute to temperature problems. Recommended Consistently abnormal fan speeds generally indicate that the fan is failing. Replace the fan Action field-replaceable unit - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 222
that it is seated correctly in the chassis. Run the psShow command to view the status of the power supply. If the power supply continues to be a problem, replace the faulty power supply. Severity INFO FW-1010 Message , [FW-1010], ,, WARNING, , , is - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 223
>, is between high and low boundaries(High=, Low=). Current value is . Probable Cause Indicates that the power supply counter changed from a value outside of the acceptable range to a value within the acceptable range. Recommended No action is required. Respond - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 224
, , value has changed(High=, Low=). Current value is . Probable Cause Indicates that the receive power value of the small form-factor pluggable (SFP) has changed. The receive performance area measures the amount of incoming laser to help you - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 225
name>, , is below low boundary(High=, Low=). Current value is . Probable Cause Indicates that the receive power value of the small form-factor pluggable (SFP) has fallen below the low boundary. The receive performance area measures the amount of incoming - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 226
Label>, is below low boundary(High=, Low=). Current value is . Probable Cause Indicates that the transmit power value of the small form-factor pluggable (SFP) has fallen below the low boundary. The transmit performance area measures the amount of outgoing laser - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 227
is between high and low boundaries(High=, Low=). Current value is . Probable Cause Indicates that the transmit power value of the small form-factor pluggable (SFP) has changed from a value outside of the acceptable range to a value within the acceptable range - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 228
29 FW-1047 FW-1047 Message , [FW-1047], ,, WARNING, , , is above high boundary(High=, Low=). Current value is . Probable Cause Indicates that the value of the small form-factor pluggable (SFP) voltage has risen - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 229
29 FW-1050 FW-1050 Message , [FW-1050], ,, WARNING, , , is below low boundary(High=, Low=). Current value is . Probable Cause Indicates that the value of the small form-factor pluggable (SFP) voltage has fallen - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 230
SFP failures also cause E_Ports to go down. E_Port downs might be caused by transient errors. A low number of E_Port failures means that the switch is functioning normally. Recommended No action is required. Respond to this message as is appropriate to the particular policy of the Action end-user - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 231
fabric reconfigurations has changed. The following actions can cause a fabric reconfiguration: • two switches with the same domain ID have connected to one another. • two fabrics have error and might not require troubleshooting. Severity INFO Fabric OS Message Reference 179 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 232
below the low boundary. The following occurrences can cause a fabric reconfiguration: • Two switches with the same domain ID have connected to one another. • Two fabrics have a transient error and might not require troubleshooting. Severity INFO 180 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 233
changes has changed. Domain ID changes occur when there is a conflict of domain IDs in a single fabric and the principal switch has to assign another domain ID to the switch. Recommended No action is required. Respond to this message as is appropriate to the particular policy of the Action end-user - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 234
the high boundary. Domain ID changes occur when there is a conflict of domain IDs in a single fabric and the principal switch has to assign another domain ID to the switch. Recommended No action is required. Respond to this message as is appropriate to the particular policy of the Action end-user - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 235
Segmentation changes might occur due to: • Zone conflicts. • Domain conflicts. • Segmentation of the principal link between two switches. • Incompatible link parameters. During E_Port initialization, ports exchange link parameters. Rarely, incompatible parameters result in segmentation. Recommended - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 236
Segmentation changes might occur due to: • Zone conflicts. • Domain conflicts. • Segmentation of the principal link between two switches. • Incompatible link parameters. During E_Port initialization, ports exchange link parameters. Rarely, incompatible parameters result in segmentation. Recommended - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 237
29 FW-1131 FW-1131 Message , [FW-1131], ,, INFO, , , is above high boundary(High=, Low=). Current value is . Probable Cause Indicates that the number of zone changes has risen above the high boundary. Zone - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 238
29 FW-1134 FW-1134 Message , [FW-1134], ,, INFO, , , is below low boundary(High=, Low=). Current value is . Probable Cause Indicates that the number of fabric logins has fallen below the low boundary. Fabric - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 239
fallen below the low boundary. SFP state changes occur when the SFP is inserted or removed. A low number of SFP state changes means that the switch is functioning normally. Recommended No action is required. Respond to this message as is appropriate to the particular policy of the Action end-user - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 240
physical and hardware problems can cause link loss errors. Link loss errors frequently occur due to a loss of synchronization. Check for concurrent loss of synchronization errors and, if applicable, troubleshoot them. A low number of link loss errors means that the switch is functioning normally - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 241
problems can cause link loss errors. Link loss errors frequently occur due to a loss of synchronization. Check for concurrent loss of synchronization errors and, if applicable, troubleshoot loss errors, troubleshoot your host bus adaptor (HBA) and contact your switch service provider. Fabric OS - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 242
form-factor pluggables (SFPs) are not faulty. If you continue to experience loss-of-synchronization errors, troubleshoot your host bus adaptor (HBA) and contact your switch service provider. Severity WARNING FW-1167 Message , [FW-1167], ,, INFO, , - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 243
experiences has changed. Loss of signal generally indicates a physical problem. Recommended Check both ends of your cable connection. Verify that user installation. A low number of signal loss errors means that the switch is functioning normally. Severity INFO FW-1170 Message , [FW- - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 244
the low boundary. Occasional protocol errors occur due to software glitches. Persistent protocol errors occur due to hardware problems. A low number of protocol errors means that the switch is functioning normally. Recommended No action is required. Respond to this message as is appropriate to the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 245
. Probable Cause Indicates that the number of invalid words that the port experiences has changed. Invalid words usually indicate a hardware problem with an small form-factor pluggable (SFP) or cable. Recommended Check both ends of your connections, your SFP, and your cable to verify - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 246
the port experiences has fallen below the low boundary. Invalid words usually indicate a hardware problem with an small form-factor pluggable (SFP) or cable. A low number of invalid words means that the switch is functioning normally. Recommended No action is required. Respond to this message as is - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 247
message as is appropriate to the particular policy of the Action end-user installation. A low number of invalid CRCs means that the switch is functioning normally. Severity INFO FW-1182 Message , [FW-1182], ,, WARNING, , , , is above - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 248
29 FW-1183 FW-1183 Message , [FW-1183], ,, INFO, , , , is between high and low boundaries(High=, Low=). Current value is . Probable Cause Indicates that the number of invalid cyclic redundancy checks - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 249
29 FW-1186 FW-1186 Message , [FW-1186], ,, INFO, , , , is above high boundary(High=, Low=). Current value is . Probable Cause Indicates that the percentage of incoming traffic that the port - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 250
29 FW-1189 FW-1189 Message , [FW-1189], ,, INFO, , , , is below low boundary(High=, Low=). Current value is . Probable Cause Indicates that the percentage of outgoing traffic that the port experiences - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 251
, has become an E_Port, has become an F_Port, has segmented, or has become a trunk port. A low number of port state changes means that the switch is functioning normally. Recommended No action is required. Respond to this message as is appropriate to the particular policy of the Action end-user - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 252
fluctuations, and aging equipment. You should set your high boundaries to five- or six-digit figures, as only large numbers of messages indicate a problem in this area. A low level of invalid CRC errors means that the switch is functioning normally. 200 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 253
fluctuations, and aging equipment. You should set your high boundaries to five- or six-digit figures, as only large numbers of messages indicate a problem in this area. Recommended No action is required. Respond to this message as is appropriate to the particular policy of the Action end-user - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 254
29 FW-1240 FW-1240 Message , [FW-1240], ,, INFO, , , value has changed(High=, Low=). Current value is . Probable Cause Indicates that the number of end-to-end (EE) cyclic redundancy check (CRC) errors has - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 255
=, Low=). Current value is . Probable Cause Indicates that the number of end-to-end (EE) word frames that the switch receives has changed. Receive performance messages appear due to the number of word frames that travel from the configured S_ID to the D_ID pair - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 256
High value>, Low=). Current value is . Probable Cause Indicates that the number of end-to-end (EE) word frames that the switch transmits has changed. Transmit performance messages appear due to the number of word frames that travel from the configured S_ID to the D_ID pair - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 257
value>, Low=). Current value is . Probable Cause Indicates that the number of end-to-end (EE) word frames that the switch transmits has fallen below the low boundary. Transmit performance messages appear due to the number of word frames that travel from the configured S_ID - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 258
fallen below the low boundary. The port has received a small computer system interface (SCSI) Read, SCSI Write, SCSI Read and Write, SCSI Traffic, or IP commands in a frame. Recommended No action is required. Respond to this message as is appropriate to the particular policy of the Action end-user - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 259
indicate that a telnet connection request has been received from an unauthorized IP address. The TELNET_POLICY contains a list of internet protocol (IP) addresses that are authorized to establish telnet connections to switches in the fabric. Recommended Action Run the errShow command to determine - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 260
indicate that a telnet connection request has been received from an unauthorized IP address. The TELNET_POLICY contains a list of internet protocol (IP) addresses that are authorized to establish telnet connections to switches in the fabric. Recommended Action Run the errShow command to determine - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 261
indicate that a browser connection request has been received from an unauthorized IP address. The HTTP_POLICY contains a list of internet protocol (IP) addresses that are authorized to establish browser connections to the switches in the fabric. Recommended No action is required. Action Severity - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 262
. The simple network management protocol policy (SNMP_POLICY) contains a list of internet protocol (IP) addresses that are authorized to establish API connections to switches in the fabric. Recommended No action is required. Action Severity INFO FW-1306 Message , [FW-1306], - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 263
. The simple network management protocol policy (SNMP_POLICY) contains a list of internet protocol (IP) addresses that are authorized to establish API connections to switches in the fabric. Recommended No action is required. Action Severity INFO FW-1308 Message , [FW-1308], - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 264
range to a value within the acceptable range. RSNMP violations indicate that an SNMP "get" operation request has been received from an unauthorized IP address. Recommended No action is required. Action Severity INFO FW-1312 Message , [FW-1312], ,, INFO, - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 265
fallen below the low boundary. WSNMP violations indicate that an SNMP "get/set" operation request has been received from an unauthorized IP address. Recommended No action is required. Action Severity INFO FW-1314 Message , [FW-1314], ,, WARNING, , - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 266
. Recommended Action Run the errShow command to determine the IP address that sent the request. Responses to security class messages . SES violations indicate that an small computer system interface (SCSI) Enclosure Services (SES) request has been received from an unauthorized world-wide name ( - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 267
outside of the acceptable range to a value within the acceptable range. SES violations indicate that an small computer system interface (SCSI) Enclosure Services (SES) request has been received from an unauthorized world-wide name (WWN). The SES_POLICY contains a list of WWNs of device ports that - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 268
of serial violations has changed. Serial violations indicate that an unauthorized serial port request has been received. The SERIAL_POLICY contains a list of switch world-wide names (WWNs) for which serial port access is enabled. Recommended Action Run the errShow command to determine the WWN of - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 269
risen above the high boundary. Serial violations indicate that an unauthorized serial port request has been received. The SERIAL_POLICY contains a list of switch world-wide names (WWNs) for which serial port access is enabled. Recommended Action Run the errShow command to determine the WWN of the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 270
violations has changed. Front panel violations indicate that an unauthorized front panel request has been received. The FRONTPANEL_POLICY contains a list of switch world-wide names (WWNs) for which front panel access is enabled. Recommended Action Run the errShow command to determine the WWN of - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 271
within the acceptable range. Front panel violations indicate that an unauthorized front panel request has been received. The FRONTPANEL_POLICY contains a list of switch world-wide names (WWNs) for which front panel access is enabled. Recommended No action is required. Action Severity INFO FW-1332 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 272
to join the fabric. The DCC_POLICY allows for the specification of rules for binding device ports (typically host bus adaptor (HBA) ports) to specific switch ports. DCC policies ensure that whenever a device performs a fabric login (FLOGI) request, the world-wide name (WWN) specified in the FLOGI is - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 273
to join the fabric. The DCC_POLICY allows for the specification of rules for binding device ports (typically host bus adaptor (HBA) ports) to specific switch ports. DCC policies ensure that whenever a device performs a fabric login (FLOGI) request, the world-wide name (WWN) specified in the FLOGI is - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 274
for binding device ports (typically host bus adaptor (HBA) ports) to specific switch ports. DCC policies ensure that whenever a device performs a fabric login (FLOGI detected. Recommended Action Run the errShow command to determine the IP location of the login attempt. Responses to security-class - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 275
detected. Recommended Action Run the errShow command to determine the IP location of the login attempt. Responses to security-class downloads a new configuration to other switches in the fabric, the packet is tagged with a timestamp. The receiving switch compares this timestamp to its current - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 276
world-wide name (WWN). When the primary fabric configuration server (FCS) downloads a new configuration to other switches in the fabric, the packet is tagged with a timestamp. The receiving switch compares this timestamp to its current time. If the difference is too great, it rejects the packet - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 277
in the fabric, the packet is signed using the private key of the primary FCS. The receiving switch has to verify this signature with the public key of the primary FCS switch. If verification fails, it rejects the packet. This counter keeps track of the number of packets received with invalid - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 278
in the fabric, the packet is signed using the private key of the primary FCS. The receiving switch has to verify this signature with the public key of the primary FCS switch. If verification fails, it rejects the packet. This counter keeps track of the number of packets received with invalid - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 279
in the fabric, the packet is signed using the private key of the primary FCS. The receiving switch has to verify this signature with the public key of the primary FCS switch. If verification fails, it rejects the packet. This counter keeps track of the number of packets received with invalid - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 280
in the fabric, it first sends its certificate to all the switches in the fabric. The receiving switch has to verify that the sender is the primary FCS switch and its certificate is signed by the Root CA recognized by the receiving switch. This counter keeps track of the number of packets received - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 281
that the number of authentication failures has fallen below the low boundary. Authentication failures can occur for many reasons. The switch on the other side might not support the protocol, have an invalid certificate, not be signed properly or send unexpected packets. The port where authentication - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 282
outside of the acceptable range to a value within the acceptable range. Authentication failures can occur for many reasons. The switch on the other side might not support the protocol, have an invalid certificate, not be signed properly or send unexpected packets. The port where authentication fails - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 283
>, is above high boundary(High=, Low=). Current value is . Probable Cause Indicates that the number of switch link authentication protocol (SLAP) faulty packets has risen above the high boundary. This counter keeps track of the number of unexpected SLAP packets - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 284
is below low boundary(High=, Low=). Current value is . Probable Cause Indicates that the number of time service (TS) out-of-sync violations has fallen below the low boundary. Recommended No action is required. Action Severity INFO FW-1366 Message - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 285
Current value is . Probable Cause Indicates that the number of time service (TS) out-of-sync violations has changed from a value outside of the acceptable fabric, but it still has the WWN of the last primary FCS switch, it increments this counter and resets the WWN of the primary FCS - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 286
finds that there are no FCSs in the fabric, but it still has the WWN of the last primary FCS switch, it increments this counter and resets the WWN of the primary FCS to all zeroes. Recommended Responses to security-class messages depend on user policies. - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 287
to a value within the acceptable range. This violation indicates the number of secure switches with different version stamps have been detected. When a switch is in secure mode, it connects only to another switch that is in secure mode and has a compatible security database. A compatible security - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 288
tracks how many times commands allowed only on the primary fabric configuration server (FCS) switch have been executed on a non-primary FCS switch. There are many commands that can be executed only on the primary FCS switch as well as one security command that can be executed only on a backup FCS - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 289
Indicates that the flash usage percentage has changed. Flash increases and decreases slightly with normal operation of the switch. Excessive permanent increases can lead to future problems. Recommended No action is required. Respond to this message as is appropriate to the particular policy of the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 290
usage percentage has risen above the high boundary. Flash increases and decreases slightly with normal operation of the switch. Excessive permanent increases can lead to future problems. Recommended You might have to remove some unwanted files to create some flash space. Run the supportSave Action - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 291
Severity WARNING FW-1427 Message , [FW-1427], ,, WARNING, , Switch status change contributing factor Power supply: bad. Probable Cause Indicates that the switch status is not in a healthy state. This occurred because the number of faulty - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 292
29 FW-1428 FW-1428 Message , [FW-1428], ,, WARNING, , Switch status change contributing factor Power supply: absent. Probable Cause Indicates that the switch status is not in a healthy state. This occurred because the number of missing - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 293
non-redundant. If you power cycle a Brocade 24000 chassis in dual-domain configuration, and then reset the micro-switch of the active CP firmware to both CPs. Replace any faulty CPs. If you reset the micro-switch (the latch on the CP blade) on the active CP before the heartbeat was up on a power - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 294
FW-1434], ,, WARNING, , Switch status change contributing factor Blade: blade failures. Probable Cause Indicates that the switch status is not in a healthy state. This occurred because the number of blade failures is greater than or equal to the policy set - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 295
faulty or deteriorating small form-factor pluggables (SFPs). Action Severity WARNING FW-1438 Message , [FW-1438], ,, WARNING, , Switch status change contributing factor Missing SFPs: missing SFPs. Probable Cause Indicates that the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 296
that the state of the specified field-replaceable unit (FRU) has changed to "inserted". This means that an FRU is inserted but not powered on. Recommended No action is required. Verify that the event was planned. Action Severity INFO FW-1442 Message , [FW-1442], - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 297
switch now requires 4 power supplies for full (2X) redundancy, but the user has previously overridden the Switch Status Policy values pertaining to number of power supplies. So those values will not be automatically changed. The default values with no AP blades are: 3 out of service indicates switch - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 298
29 FW-1500 FW-1500 Message , [FW-1500], ,, WARNING, , Mail overflow - Alerts being discarded. Probable Cause Indicates that mail alert overflow condition has occurred. Recommended Resolve or disable the mail alert using the fwMailCfg command. Action - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 299
possible. Recommended Action Reboot the standby CP blade by ejecting the card and reseating it. If the problem persists, replace the standby CP. Severity This message records switch processor reboot reasons that were initiated by the user or the switch errors. The switch processor reboots can - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 300
30 HAM-1005 • Unknown • Fastboot • Giveup Master:SYSM • CP Faulty:SYSM • FirmwareDownload • ConfigDownload:MS • ChangeWWN:EM • Reboot:WebTool • Fastboot:WebTool • Software Fault:Software Watchdog • Software Fault:Kernel Panic • Software Fault:ASSERT • Reboot:SNMP • Fastboot:SNMP • Reboot • Chassis - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 301
30 HAM-1006 Recommended The standby CP will take over and reset the active CP.The system will be non-redundant as the Action standby becomes the active CP. Severity CRITICAL Fabric OS Message Reference 249 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 302
30 HAM-1006 250 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 303
FTP transfers; then run the supportSave command and contact your switch service provider. Severity CRITICAL HAMK-1002 Message , [HAMK- the active CP after 10 minutes, reboot the standby CP blade by ejecting the blade and reseating it. Severity INFO HAMK-1003 Message , - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 304
31 HAMK-1004 HAMK-1004 Message ,[HAMK-1004], ,, INFO, , Resetting standby CP (double reset may occur). Probable Cause Indicates that the standby control processor (CP) is being reset due to a loss of heartbeat. This message is typically seen when the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 305
32 HIL-1101 Message , [HIL-1101], ,, ERROR, , Slot faulted, () is above threshold. Probable Cause Indicates that the blade voltage is above the threshold. Recommended Replace the faulty blade or switch - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 306
, and 4024 the entire switch must be replaced, because these switches do not have field-replaceable units (FRUs). For the Brocade 3900, replace the motherboard FRU. For the Brocade 4100, 4900, 5000, 7500, and AP7600, if the 12 volt level is faulty, replace one or both power supplies; if any other - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 307
, and 4024 the entire switch must be replaced, because these switches do not have field-replaceable units (FRUs). For the Brocade 3900, replace the motherboard FRU. For the Brocade 4100, 4900, 7500, and AP7600, if the 12 volt level is faulty, replace one or both power supplies; if any other voltage - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 308
not applicable to the Brocade 24000, or 48000. Recommended Action For the Brocade 3900 replace the fan field-replaceable unit (FRU). For the Brocade 3016, 3250 and 3850, the entire switch must be replaced, because these switches do not have FRUs. Severity ERROR 256 Fabric OS Message Reference - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 309
32 HIL- problem can quickly cause the switch to overheat. This message is specific to nonbladed switches and is not applicable to the Brocade 24000, or 48000. Recommended For the Brocade range of your switch. Refer to the hardware reference manual for your switch for the operational temperature - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 310
32 HIL-1301 HIL-1301 Message , [HIL-1301], ,, WARNING, < been removed. This message is often preceded by a low speed error message. This problem can cause the switch to overheat. Recommended Replace the affected fan FRU immediately. Action Severity WARNING HIL-1302 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 311
32 HIL-1305 Severity ERROR HIL-1305 Message , [HIL-1305], ,, ERROR, , One or two fan(s) failed. Replace failed fan FRUs immediately. - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 312
32 HIL-1309 Recommended Replace the faulty fan field-replaceable units (FRUs) immediately. by a low fan speed message. Recommended Since the fans are not field replaceable, replace the switch if the temperature is high. Action Severity WARNING HIL-1311 Message , [HIL-1311], < - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 313
32 HIL-1402 Probable Cause Indicates that one fan field-replaceable unit (FRU) has , , Slot , high temperature (). Indicates that the temperature of this blade has risen above the warning threshold. Fabric OS Message Reference 261 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 314
and that the room temperature is within operational range of your switch. Refer to the hardware reference manual for your switch for the operational temperature range. If the message persists, replace the blade. Severity CRITICAL HIL-1503 Message , [HIL-1503], , FFDC - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 315
32 HIL-1505 Recommended No action is required. Action Severity INFO problems, make sure that all the fans are working properly. Make sure that the area is well ventilated and that the room temperature is within operational range of your switch. Refer to the hardware reference manual for your switch - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 316
32 HIL-1508 HIL-1508 Message , [HIL-1508], - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 317
> fans out of service. System is shutting down immediately. Probable Cause Indicates that total fan failure count is greater than or equal to two. Recommended In order to avoid causing damage to the switch, the system shuts down automatically. To help Action prevent future problems, make sure that - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 318
32 HIL-1650 Severity ERROR 266 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 319
. Probable Cause Indicates that the HLO message was incompatible with the value specified in the FSPF protocol. The Brocade switch will not accept FSPF frames from the remote switch. In the Fabric OS, the HLO timeout value is not configurable, so this error can only occur when the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 320
number in the HLO message has an invalid value. This error can only occur when the Brocade switch is connected to a switch from another manufacturer. Recommended The HLO message of the remote switch must be compatible with the value specified in the FSPF Action protocol. Refer to documentation of - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 321
Action Run the firmwareDownload command to reinstall the firmware to your switch. If the message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity CRITICAL Fabric OS Message Reference 269 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 322
34 HMON-1001 270 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 323
>, [HTTP-1001], ,, INFO, , Switch PIDformat has changed to . Probable Cause Indicates that information on PID, format refer to the Fabric OS Administrator's Action Guide. Severity INFO HTTP-1002 Message , [HTTP-1002], - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 324
35 HTTP-1003 272 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 325
has crashed unexpectedly and restarting attempts have failed. Recommended Power off and power on the blade using the slotPowerOff and slotPowerOn commands. On the Action Brocade 7500 or 7600, switch off and on all primary power in order to power-cycle the unit. Severity WARNING Fabric OS Message - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 326
36 IBD-1001 274 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 327
target name length exceeds the character limit [] Probable Cause Indicates that the target name length exceeds the supported limit. Recommended Redo the discovery to get the latest target list, and try again. Action Severity WARNING IBPD-1003 Message - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 328
37 IBPD-1003 276 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 329
or power cycle the switch. Severity ERROR ICPD-1002 Message , [ICPD-1002], ,, ERROR, , Failed to initialize rc = . Probable Cause Indicates that an initialization of a module within the ICPD failed. Recommended Download a new firmware - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 330
ICPD-1007 Message , [ICPD-1007], ,, INFO, , iSNSC service is on the switch. Probable Cause Indicates that the iSNSC service is enabled or disabled on the switch. Recommended No action is required. Action Severity INFO 278 Fabric OS Message - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 331
38 ICPD-1008 ICPD-1008 Message , [ICPD-1008], ,, INFO, , iSCSI switch () is . Probable Cause Indicates that the iSCSI switch is reachable or unreachable. Recommended No action is required. Action Severity INFO Fabric OS Message - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 332
38 ICPD-1008 280 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 333
of address change> Probable Cause Indicates that a change in local IP address has occurred. If the source of the address change is manual, this means that the address change was initiated by a user. If the source of the address change is the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 334
39 IPAD-1001 282 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 335
module within the IPS daemon failed. Recommended Download a new firmware version using the transient problem. Recommended Action If the message persists, check the memory usage on the switch, contact your switch service provider. Severity WARNING IPS-1004 Message , [IPS-1004], - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 336
return the Action port mode to neutral before attempting to configure the port for a different mode or use. Severity WARNING IPS-1005 Message , [IPS-1005], ,, WARNING, , Tunnel Authorization Failure for slot () port(ge) tunnel ID( - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 337
Chapter ISCS System Messages 41 ISCS-1000 Message , [ISCS-1000], ,, ERROR, , Slot Port GE crashed unexpectedly. Probable Cause Indicates that specified port has crashed. Recommended No action is required; the port will - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 338
41 ISCS-1000 286 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 339
>, [ISNS-1003], ,, INFO, , Peering with external iSNS server is disabled. Probable Cause Indicates that the IP address of internet storage name service (iSNS) server is set to zero, so peering is disabled. Recommended If you wish to enable the iSNS server, use the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 340
Period in seconds>. Probable Cause Indicates that the internet storage name service (iSNS) client failed to receive a successful response for a , Start re-register with external iSNS server slot/port /ge. Probable Cause Indicates that - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 341
Peering with external iSNS server not started because no virtual targets Refer to the appropriate hardware reference manual for valid slot and Action port ranges Service is . Indicates the current state of the internet storage name service - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 342
INFO, , Start peering with external iSNS server on management port. Probable Cause Indicates that peering has started with the specified external internet storage name service (iSNS) on the management port. Recommended No action is required. Action Severity - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 343
Chapter FCR System Messages 43 FCR-1001 Message , [FCR-1001], ,, INFO, , FC router proxy device in edge created at port . Probable Cause Indicates that a proxy device in the edge fabric has been imported at the specified port. Recommended - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 344
43 FCR-1004 FCR-1004 Message , [FCR-1004], ,, INFO, , FC router physical devices offline at port . Probable Cause Indicates that one or more physical devices connected to the specified port have gone offline. Recommended Action Verify that - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 345
43 FCR-1008 Severity INFO FCR-1008 Message , [FCR-1008], ,, INFO, , FC router LSAN zone created at port . Probable Cause Indicates that a logical storage area network (LSAN) zone was created at the specified port in the edge fabric. - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 346
id fabric ID . Indicates that a fabric is no longer accessible through the backbone fabric. This may be caused by a link or switch failure. 294 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 347
device port resources. Use the fcrProxyDevShow command to view how many proxy devices are created in the fabric with the port resource problem. LSAN zones are removed using standard zoning commands such as zoneShow, zoneRemove, zoneDelete, cfgDelete, and cfgDisable in the edge fabric. Proxy devices - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 348
43 FCR-1021 To do that, perform the following steps: 1. Run portDisable to disable all the EX_Ports that got this error message. 2. Run portDisable to disable all the other EX_Ports on that FCR connected to the same edge fabrics the EX_ports disabled in step 1 are connected to. 3. Use Zoning - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 349
be in use are reused as needed. Recommended Action It is unlikely that WWN conflicts will occur as a result of pool rollover unless the switch is deployed in a very large MetaSAN environment with large number of logical storage area network (LSAN) devices and fabrics, or there are highly dynamic - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 350
in use will be reused as needed. Recommended Action It is unlikely that WWN conflicts will occur as a result of pool rollover unless the switch is deployed in a very large MetaSAN environment with large number of logical storage area network (LSAN) devices and fabrics, or there are highly dynamic - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 351
43 FCR-1030 To avoid WWN conflicts, all EX_Ports attached to fabrics with highly dynamic changes to EX_Port connectivity should be disabled then reenabled. Severity INFO FCR-1030 Message , [FCR-1030], ,, INFO, , Physical device came online at - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 352
43 FCR-1034 Recommended No action is required. Action Severity INFO FCR-1034 Message , [FCR-1034], ,, INFO, , LSAN zone added in backbone fabric. Probable Cause Indicates that a new logical storage area network (LSAN) zone was added to the backbone - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 353
: . Probable Cause Indicates that the number of cfg/zone/alias entries created in a local fabric is greater than the local switch's zone database limitations. Recommended Remove excess cfg/zone/alias entries so that the number of logical storage area network (LSAN) Action zones - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 354
Setting port credits failed. Execute the portEnable command. If the problem persists try rebooting the switch. If the message persists, collect switch information using the supportShow command, and contact your switch service provider. Severity ERROR 302 Fabric OS Message Reference 53-1000600 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 355
link protocol (ELP) command was issued and it is not supported. Recommended Action Run the portEnable and portDisable commands to enable and disable the port. If the problem persists contact your switch service provider. Severity ERROR FCR-1053 Message , [FCR-1053], - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 356
in the MetaSAN. Recommended No action is required if backbone-to-edge routing is not needed. Otherwise replace the switch with Action one that supports backbone to edge routing. Severity INFO FCR-1057 Message , [FCR-1057], ,, ERROR, , EX_Port( - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 357
() has an incompatible configuration setting. Probable Cause Indicates that virtual channel (VC) Link Init is enabled on the local switch and the remote switch is negotiating in R_RDY mode. The fabric might not form properly. Recommended Action Check the configuration on the local - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 358
, system only supports EX/VEX_ports. Probable Cause Indicates that the maximum number of supported EX_ports or VEX_ports >. Probable Cause Indicates that the fabric ID of the switch does not match the local switch. Recommended Run the switchShow command to display the fabric - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 359
the switch is the fabric split, then merge the fabrics and manually re-enable the port. If there is another fabric connected fabric exceeds the maximum number supported by the Fibre Channel. The limit FC Routing service is disabled. Probable Cause Indicates that the FC Routing service is disabled - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 360
with the fcrState set to 1 (enabled). Note that the FC Routing service is disabled by the factory. Recommended No action is required. Action Severity FC Routing configuration is set to default. Probable Cause Indicates that the FC Routing configuration is set to default by user. This removes all - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 361
switch in the backbone/edge that supports different limit of logical storage area network (LSAN) zones was detected. Recommended Action Use the fcrResourceShow command on all Fibre Channel Routers in the Meta-SAN to find the lowest supported ) has older firmware, which only supports a lower number - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 362
sure to remain within the maximum of supported front domains. Action Severity ERROR FCR-1077 binding list details configured on the M-Model switch does not match with the currently configured of the LSAN name exceeds the limit of 64 characters. Recommended Please change the name and reactivate - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 363
found, run supportFtp to send all core files to a secure server location. Copy the warning message along with any core file information, and contact your switch service provider. Severity WARNING Fabric OS Message Reference 311 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 364
44 KSWD-1003 312 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 365
Chapter KTRC System Messages 45 KTRC-1001 Message , [KTRC-1001], ,, WARNING, , Dump memory size exceeds dump file size Probable Cause Indicates that the dump memory size has exceeded the dump file size. Recommended No action is required. Action - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 366
45 KTRC-1005 Recommended No action is required. Action Severity ERROR KTRC-1005 Message , [KTRC-1005], ,, ERROR, , Trace initialization failed. . . Probable Cause Indicates that Trace was unable to - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 367
or the haFailover command on bladed switches. If the message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity WARNING LOG-1002 Message , [LOG-1002], , FFDC - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 368
46 LOG-1003 LOG-1003 Message , [LOG-1003], ,, INFO, , The log has been cleared. Probable Cause Indicates that the persistent error log has been cleared. Recommended No action is required. Action Severity INFO 316 Fabric OS Message Reference 53- - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 369
valid link state ID is the same as the valid domain ID, whose range is from 1 through 239. The switch will discard the record because it is not supported. Recommended No action is required. Action Severity ERROR LSDB-1002 Message , [LSDB-1002], ,, INFO, - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 370
domain Probable Cause Indicates that there is no link state record for the specified local domain. Recommended No action is required. The other switch will pass the LSD when the fabric has become stable. Action Severity WARNING 318 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 371
System Messages 48 MFIC-1001 service provider. Severity ERROR MFIC-1002 Message , [MFIC-1002], ,, INFO, , Chassis FRU header not programmed for switch NID, using defaults (applies only to FICON environments). Probable Cause Indicates that custom switch - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 372
48 MFIC-1003 MFIC-1003 Message , [MFIC-1003], ,, WARNING, , Effective Insistent domain ID for the fabric changed from to Probable Cause Indicates that one or more switches joined the fabric with a different insistent domain ID (IDID) mode - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 373
Chapter MPTH System Messages 49 MPTH-1001 Message , [MPTH-1001], , FFDC, ERROR, , Null parent, lsId = Probable Cause Indicates that a null parent was reported. MPATH uses a tree structure in which the parent is used to connect to the root of - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 374
49 MPTH-1003 322 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 375
• 7 - MSG_LINIT_IU • 8 - MSG_RSCN • 9 - MSG_IOCTL • 10 - MSG_ACCEPT • 11 - MSG_IU_FREE • 12 - MSG_US • 13 - MSG_EXT_RSCN • 14 - MSG_RDTS_START • 15 - MSG_RDTS_SENDEFP • 16 - MSG_RDTS_RESET Recommended No action is required. Action Severity ERROR Fabric OS Message Reference 323 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 376
50 MQ-1004 324 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 377
. Recommended Action: Set the flag for the MS Platform Service. • The GCAP (MS Get Capabilities) is not supported by another switch. Recommended Action: Upgrade the firmware level on the switch to a level that supports RCS. • The request to the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 378
) by> Run the firmwareDownload command to upgrade the firmware level on the switch to a level that supports RCS. RCS is supported in Fabric OS v2.6, v3.1 and FTP transfers; then run the supportSave command and contact your switch service provider. Severity INFO MS-1004 Message , [MS- - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 379
If the message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity ERROR MS-1008 Message , [MS-1008], ,, ERROR, , MS Failure while initializing - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 380
following messages might be displayed: • Exceeded bit error rate threshold • Loss of signal or RLIR incidents are likely due to SAN hardware problems such as bad cables, small form run the Action supportSave command and contact your switch service provider. Severity ERROR MS-1022 Message < - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 381
, [MS-1023], ,, INFO, , Management Server Topology Discovery Service Probable Cause Indicates that Management Server Topology Discovery Service is being enabled or disabled. Recommended No action is required. Action Severity INFO MS - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 382
51 MS-1024 330 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 383
this error occurs repeatedly, it means the protocol implementation between two connected switches has problems. Recommended Action Run the nbrStateShow command to check the neighbor state of the port listed in the message. If it is FULL, then this message can safely be ignored. Otherwise, run the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 384
(NBFSM) states are as follows: • 0 - Down • 1 - Init • 2 - Database Exchange • 3 - Database Acknowledge Wait • 4 - Database Wait • 5 - Full Recommended No action is required. The Fabric OS auto recovers from this problem. Action Severity WARNING 332 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 385
payload exceeds the maximum frame size that the remote switch can handle. Recommended Action Run the firmwareDownload command to upgrade the remote switch with firmware v4.3 or higher, as appropriate for the switch type, so that it can support GMI to handle frame fragmentation and reassembly. You - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 386
on the standby CP has lower supported capability than the active CP due to different firmware versions running on the active and switch can support. The oversized portion will be truncated. Recommended Reduce the zone size to 1024 or lesser, or upgrade the software of the remote switch to support - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 387
. Recommended Action Run the firmwareDownload command to reinstall the firmware. If the message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity WARNING Fabric OS Message Reference 335 53 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 388
PDM) process ran out of memory. Recommended Action Reboot or power cycle the switch. If the message persists, run supportFtp (as needed) firmware. If the message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 389
. Recommended Action Run the firmwareDownload command to reinstall the firmware. If the message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity WARNING Fabric OS Message Reference 337 53 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 390
. Recommended Action Run the firmwareDownload command to reinstall the firmware. If the message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity WARNING PDM-1012 Message , [PDM - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 391
Recommended Action Run the firmwareDownload command to reinstall the firmware. If the message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity CRITICAL PDM-1019 Message , [PDM - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 392
is not supported by older firmware. Recommended Action Run the firmwareDownload command to reinstall the firmware. If the message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity WARNING - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 393
54 PDM-1024 Fabric OS Message Reference 341 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 394
54 PDM-1024 342 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 395
the panic dump and core dump files and a trap generated. The watchdog register codes are as follows: • 0x10000000 bit set means that the watch dog timer (WDT) forced a core reset. • 0x20000000 bit set means that the WDT forced a chip reset. • All other code values are reserved. Recommended Run the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 396
55 PDTR-1002 344 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 397
up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity CRITICAL PLAT-1001 Message , [PLAT-1001], - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 398
56 PLAT-1002 Severity CRITICAL 346 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 399
specified port is now disabled because the link on this port had multiple failures that exceed an internally set threshold on the port. This problem is typically related to hardware. Recommended Action Check and replace (if necessary) the hardware attached to both ends of the specified port number - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 400
-1005 PORT-1005 Message , [PORT-1005], ,, WARNING, , Slot port does not support configured L_port. Issue portCfgLport to clear configuration. Probable Cause Indicates that the specified port is configured to be an L_port, but - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 401
automatically. If it does not, reboot or power cycle the switch to Action reinitiate the firmware. Severity CRITICAL PS-1001 Message , Recommended No action is required. Refer to the Fabric OS Administrator's Guide for more information about the Action PID format. Severity INFO PS- - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 402
has attempted to add end-to-end monitors on at least one ISL port. Recommended No action is required. End-to-end monitoring is not supported on ISL ports when ISL monitoring is Action enabled. ISL monitoring can only be disabled through the Fabric Access API. Severity WARNING PS-1005 Message - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 403
Probable Cause Indicates that the portSwap feature has been enabled in the switch. Recommended No action is required. Action Severity INFO PSWP-1003 Cause Indicates that the portSwap feature has been disabled in the switch. Recommended No action is required. Action Severity INFO Fabric OS - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 404
59 PSWP-1003 352 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 405
Indicates that the maximum storage size for FFDC data capture is reached. Recommended Run the supportSave command and contact your switch service provider. Action Severity WARNING RAS-1004 Message , [RAS-1004], , FFDC, WARNING, , Software 'verify' error - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 406
internal software error. Recommended Run the supportSave command and contact your switch service provider. Action Severity WARNING RAS-1006 Message , [RAS-1006], , INFO, , Support data file () automatically transferred to remote address - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 407
60 RAS-3001 Probable Cause A user has changed the configured classes of the audit feature. Recommended No action is required. Action Severity INFO RAS-3001 Message , [RAS-3001], , INFO, , USB storage device plug-in detected. Probable Cause Indicates that - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 408
60 RAS-3004 Recommended No action is required. Action Severity INFO 356 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 409
v4.1 and greater. Run the firmwareDownload command to upgrade the firmware for any switches that do not support RCS. Severity INFO RCS-1002 Message , . Check memory usage on the switch using the memShow command. Reboot or power cycle the switch. Severity ERROR Fabric OS Message - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 410
in Fabric OS v2.6, v3.1 and greater, v4.1 and greater. Run the firmwareDownload command to upgrade the firmware for any switches that do not support RCS. Severity ERROR RCS-1005 Message , [RCS-1005], ,, INFO, , Phase , - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 411
remote domain rejected an RCS phase initiated by an application on the local switch. If the reject phase is ACA, the remote domain might be busy and might not be compatible or the domain does not have the license to support that application. Recommended Action If the reject is in ACA phase, wait - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 412
61 RCS-1008 360 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 413
Cause Indicates that an authentication error was reported. The specified client IP address has faulty credentials. Recommended Enter the correct user name and Probable Cause Indicates that the SSL certificate file configured on the switch could not be accessed because root did not have read-level - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 414
, , Permission denied accessing private key file. Secure RPCd is disabled. Probable Cause Indicates that the private key file configured on the switch could not be accessed because root did not have read-level access. Recommended Change the file system access level for the private key - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 415
Count • detail4: Status • detail5: Process ID Recommended Action Run the fabricShow command to see if the specified domain ID is online. Enable the switch with the specified domain ID. If the message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 416
ID is reachable. If the message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity INFO 364 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 417
Chapter SAS System Messages 64 SAS-1001 Message , [SAS-1001], ,, ERROR, , string description of command which failed> of GE failed. - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 418
64 SAS-1001 366 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 419
queue has failed because the SCN queue for the specified daemon name is full. This might be caused by the daemon hanging or if the system is switch. If the message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 420
65 SCN-1001 368 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 421
. If the message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity ERROR SEC-1002 Message , [SEC-1002], ,, ERROR, , Security data fails: - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 422
message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity WARNING SEC-1005 Message , [SEC-1005], ,, INFO, , Primary FCS receives data request from - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 423
HTTP connection. Probable Cause Indicates that a security violation was reported. The IP address of the unauthorized host is displayed in the message. Recommended Check for unauthorized access to the switch through the HTTP connection. Action Severity INFO SEC-1009 Message , [SEC - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 424
The IP address of the unauthorized host is displayed in the message. Recommended Check for unauthorized access to the switch through Fabric OS Administrator's Guide. If a certificate does not exist or is invalid, install the certificate by following the field upgrade process. Severity WARNING - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 425
() detected. Probable Cause Indicates that a corruption occurred during the distribution of the security database. This can occur only when the primary fabric configurations server (FCS) distributes the security database to the other switches in the fabric, then local validation - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 426
error state, the database might not be correctly updated for that specific switch. Severity ERROR SEC-1031 Message , [SEC-1031], ,, WARNING, , Current security policy DB cannot be supported by standby. CPs will go out of sync. Probable Cause Indicates - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 427
command. Only the secPolicyCreate command supports use of the asterisk for adding switches to policies. Recommended Action Run the secPolicyAdd command using a valid switch identifier (WWN, domain ID, or switch name) to add specific switches to the switch connection control (SCC) policy. Refer - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 428
world-wide name (WWN) entered in the policy member list had an invalid format. Recommended Run the command again using the standard WWN format, 16 hexadecimal digits grouped as eight Action colon separated pairs. For example: 50:06:04:81:D6:F3:45:42. Severity ERROR SEC-1038 Message - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 429
66 SEC-1040 SEC-1040 Message , [SEC-1040], ,, ERROR, , Invalid portlist (). Cannot combine * with port member in the same portlist. Probable Cause Indicates that the port list contains the wildcard asterisk (*) character. You cannot use the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 430
of the security database. This can only occur when the primary fabric configurations server (FCS) is distributing the security database to the other switches in the fabric and local validation finds that there is an error in the security database. This is a rare occurrence. Recommended Action Run - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 431
of the security database. This can only occur when the primary fabric configurations server (FCS) is distributing the security database to the other switches in the fabric and local validation finds that there is an error in the security database. This is a rare occurrence. Recommended Action Run - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 432
of the security database. This can only occur when the primary fabric configurations server (FCS) is distributing the security database to the other switches in the fabric and local validation finds that there is an error in the security database. This is a rare occurrence. Recommended Action Run - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 433
of the security database. This can only occur when the primary fabric configurations server (FCS) is distributing the security database to the other switches in the fabric and local validation finds that there is an error in the security database. This is a rare occurrence. Recommended Action Run - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 434
configurations server (FCS) is distributing the security database to the other switches in the fabric and local validation finds that there is an error in either that no domains or domains more than the maximum number supported are specified. Recommended Enter the correct number of domains. Action - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 435
Action generate the PKI objects and install the certificate by following the field upgrade process. Severity ERROR SEC-1065 Message , [SEC-1065], - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 436
. Recommended Run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command Action and contact your switch service provider. Severity ERROR SEC-1073 Message , [SEC-1073], ,, ERROR, , No FCS policy in list! Probable - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 437
not allowed in non-secure mode is attempted, do not perform the operation in non-secure mode. In secure mode, run the command from a switch that has required privilege, that is, either a backup FCS or primary FCS. Severity ERROR SEC-1075 Message , [SEC-1075], ,, ERROR - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 438
66 SEC-1077 SEC-1077 Message , [SEC-1077], ,, ERROR, , Failed to activate new policy set on all switches. Probable Cause Indicates that the policy could not be activated. Possible reasons that the policy could not be activate include not enough memory or - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 439
of the security database. This can only occur when the primary fabric configurations server (FCS) is distributing the security database to the other switches in the fabric and local validation finds that there is an error in the security database. This is a rare occurrence. Recommended Action Run - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 440
of the security database. This can only occur when the primary fabric configurations server (FCS) is distributing the security database to the other switches in the fabric and local validation finds that there is an error in the security database. This is a rare occurrence. Recommended Action Run - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 441
of the security database. This can only occur when the primary fabric configurations server (FCS) is distributing the security database to the other switches in the fabric and local validation finds that there is an error in the security database. This is a rare occurrence. Recommended Action Run - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 442
of the security database. This can only occur when the primary fabric configurations server (FCS) is distributing the security database to the other switches in the fabric and local validation finds that there is an error in the security database. This is a rare occurrence. Recommended Action Run - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 443
of the security database. This can only occur when the primary fabric configurations server (FCS) is distributing the security database to the other switches in the fabric and local validation finds that there is an error in the security database. This is a rare occurrence. Recommended Action Run - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 444
fabric configurations server (FCS) is distributing the security database to the other switches in the fabric and local validation finds that there is an error in the Action supportSave command and contact your switch service provider. Severity ERROR 392 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 445
could not be found. Recommended Run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command Action and contact your switch service provider. Severity ERROR SEC-1099 Message , [SEC-1099], ,, ERROR, , Please enable your - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 446
one or more switches in the fabric switches in the fabric are in the ready state. When all switches switch failed to download certificate, security database, or policies. This can happen when switch Probable Cause Indicates that the switch failed to get either that the primary switch has a valid - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 447
for re-creating PKI objects outlined in the Secure Fabric OS Administrator's Guide. Severity ERROR SEC-1107 Message , [SEC-1107], - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 448
security event was planned. If the security event was planned, run the secFabricShow command to verify that all switches in the fabric are in the ready state. When all switches are in the ready state, retry the operation. Severity ERROR SEC-1110 Message , [SEC-1110], - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 449
-name>, FCS list must be the first entry in the Active Security policies, and the same as the current active FCS list in the switch. Probable Cause Indicates that either a security policy download is attempted with an active policy that does not have the fabric configurations server (FCS) policy - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 450
all switches are in the ready state, retry the operation. Severity INFO SEC-1118 Message , [SEC-1118], ,, INFO, , Fail to set SNMP string. Probable Cause Indicates that the SNMP string could not be set. Recommended Usually this problem is transient - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 451
, [SEC-1121], ,, ERROR, , Time is out of range when . Probable Cause Indicates that the time on the switch is not synchronized with the primary fabric configurations server (FCS), the data packet is corrupted, or a replay attack is launched on the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 452
INFO SEC-1130 Message , [SEC-1130], ,, INFO, , The Primary FCS has failed over to a new switch. Probable Cause Indicates that an FCS failover operation was completed successfully. Recommended Action Verify that the security event was planned. If the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 453
from the primary fabric configurations server (FCS) switch. This message usually indicates that the data package is corrupted, the time stamp on the package is out of range as a result of a replay attack or out-of-sync time service, or the signature verification failed. Signature verification - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 454
from the primary fabric configurations server (FCS) switch. This message usually indicates that the data package is corrupted, the time stamp on the package is out of range as a result of a replay attack or out-of-sync time service, or the signature verification failed. Signature verification - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 455
by 16. The support RCS, obtain the latest firmware version from your switch supplier, and run the firmwareDownload command to upgrade the firmware. If the message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 456
the failed command. If the message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity INFO 404 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 457
of the security database. This can only occur when the primary fabric configurations server (FCS) is distributing the security database to the other switches in the fabric and local validation finds that there is an error in the security database. This is a rare occurrence. Recommended Action Run - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 458
Severity ERROR SEC-1165 Message , [SEC-1165], ,, ERROR, , Low memory, failed to enable security on all switches. Probable Cause Indicates that the system is low on memory. Recommended Wait a few minutes and try the command again. Action Severity ERROR - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 459
of the security database. This can only occur when the primary fabric configurations server (FCS) is distributing the security database to the other switches in the fabric and local validation finds that there is an error in the security database. This is a rare occurrence. Recommended Action Run - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 460
of the security database. This can only occur when the primary fabric configurations server (FCS) is distributing the security database to the other switches in the fabric and local validation finds that there is an error in the security database. This is a rare occurrence. Recommended Action Run - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 461
to set password. Probable Cause Indicates that the FCS or non-FCS password could not be set. Recommended Verify that all switches in the fabric are in time synchronization with the primary and that no Action external entity is trying to access the fabric. When verification is - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 462
with a valid value. If the message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity ERROR 410 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 463
DB. Probable Cause Indicates that the switch database was enabled or disabled as the secondary authentication, accounting, and authorization (AAA) mechanism when the Remote Authentication Dial-in User Service (RADIUS) / Lightweight Directory Access Protocol (LDAP) is the primary AAA mechanism - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 464
name> tries to FLOGI to index/area of switch . Probable Cause Indicates that a device connection control (DCC) number>,, INFO, , Security violation: Unauthorized host with IP address tries to do SNMP write operation. Probable Cause Indicates - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 465
>,, INFO, , Security violation: Unauthorized host with IP address tries to do SNMP read operation. Probable Cause Indicates attempted to establish an HTTP connection. Recommended Action Check if the host IP address specified in the message can be used to manage the fabric - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 466
through the specified connection method; the login failed. Recommended The error message lists the violating IP address. Verify that this IP address is being used by a valid Action switch admin. Use the correct password. Severity INFO SEC-1194 Message , [SEC-1194], - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 467
Switch does not have all default account names. Probable Cause Indicates that the default switch accounts admin and user do not exist on the switch when enabling security. Recommended Reset the default Recommended Action Check to see if the host IP address specified in the message can be used to - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 468
. An attempt was made to access the serial console on the specified switch instance when it is disabled. Recommended Action Check to see if an authorized access attempt is being made on the console. If so, add the switch world-wide name (WWN) to the serial policy. If the host is not allowed - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 469
Login information: Login successful via TELNET/SSH/RSH. IP Addr: Probable Cause Indicates the IP address of the remote station logging in. Recommended No the supportSave command and contact your switch service provider. Severity WARNING Fabric OS Message Reference 417 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 470
run the supportSave command and contact your switch service provider. Severity ERROR SEC-1300 Message , [SEC-1300], ,, INFO, , This switch is in VcEncode mode. Security is not supported. Probable Cause Indicates that the switch is set up with VC-encoded - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 471
Secure Fabric OS feature. Recommended Run the firmwareDownload command to update the firmware to the latest version for your specific Action switch. Verify that the firmware you are installing supports the Brocade Secure Fabric OS feature. Severity INFO Fabric OS Message Reference 419 53 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 472
to validate PKI objects occurs, follow the steps for re-creating PKI objects outlined in the Secure Fabric OS Administrator's Guide. If PKI objects are valid, verify that an unauthorized switch is not trying to access the fabric. Severity INFO 420 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 473
/LDAP server identity>. Probable Cause Indicates that after some servers timed out, the specified remote authentication dial-in user service (RADIUS/LDAP) server responded to a switch request. Recommended If the message appears frequently, move the responding server to the top of the RADIUS/LDAP - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 474
. Probable Cause Indicates that the security enable failed on the fabric because one or more switches in the fabric have password policies that are not set to the default value. Recommended Action Verify that the security event was planned. If the security event was planned, run the passwdCfg - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 475
. Probable Cause Indicates that the call to the EM module to retrieve the IP address failed. Recommended Please reboot the system to fix this error. If the problem persists contact your switch service Action provider. Severity ERROR SEC-1315 Message , [SEC-1315], - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 476
, , Non-acl domain tries to join a fabric with strict fabric wide policy Probable Cause Indicates that a domain not supporting an access control list (ACL) policy tried to join a fabric with a strict fabric-wide policy. Recommended No action is required. The domain is - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 477
Indicates that the security enable failed on the fabric because switch has conflicting configuration such as fabric wide consistency configuration or to support a device connection control (DCC) policy with more than 256 ports. Recommended Reconfigure any policy that includes more than 256 ports - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 478
error: Probable Cause Indicates that the reliable commit service (RCS) transaction failed with specified reason code. Recommended Verify that ], ,, ERROR, , Security enforcement: Switch connecting to port is not authorized to - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 479
>. Probable Cause Indicates that the IP filter policy enforcement failed due to internal system failure. Recommended Run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command Action and contact your switch service provider. Severity ERROR SEC-1330 Message - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 480
. Reason: . Probable Cause Indicates that the secModeEnable command failed on the fabric, because default IP Filter policies are not active on the switch, or an active transaction exists on IP Filter policies. Recommended Action Verify that the security event was planned. If the security - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 481
SNMP) service could not be started because of the specified Reason. You will not be able to query the switch through SNMP. Recommended Verify that the IP address (SNMP) service failed and you will not be able to query the switch through SNMP. Recommended Reboot or power cycle the switch. This will - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 482
Indicates that the simple network management protocol (SNMP) configuration is incorrect and the SNMP service will not work correctly. Recommended Change the SNMP configuration back to the default. Action Severity ERROR SNMP-1005 Message , [SNMP-1005], , AUDIT, INFO - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 483
uploaded support information to the host with IP address . Probable Cause Indicates that the supportSave command was used to transfer support command to set the FTP or SCP parameters. Action After the problem is corrected, rerun the supportSave command. Severity WARNING SS-1002 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 484
due to possible errors in subcommands being executed by the supportSave command. Recommended Run usbstorage to check the USB storage device settings. After the USB problem is corrected, Action rerun the supportSave command. Severity WARNING 432 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 485
power down the system during firmware upgrade. Allow the firmwareDownload command to continue without disruption. Do not fail over or power down the system during firmware upgrade the firmwareDownload command has completed successfully and switch firmware has been updated. Recommended Action No - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 486
,, INFO, , Standby CP reboots. Probable Cause Indicates that the standby CP is rebooting with new firmware. Recommended Action No action is required. The firmwareDownload command is progressing as expected. Run the firmwareDownloadStatus command for more information - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 487
failed on Standby CP." "firmwareCommit failed on Standby CP." "firmwareDownload failed." "firmwareDownload failed due to IPC error." "Unable to check the firmware version on Standby CP due to IPC error." "firmwareDownload failed due to IPC error." "firmwareDownload failed due to IPC error." "Standby - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 488
secondary partition. Please use firmwareDownloadStatus and firmwareShow to see firmware status." "firmwareDownload has started on Standby CP. up." "Standby CP booted up with new firmware." "Standby CP failed to boot up with new firmware." "firmwareDownload has completed successfully on Standby CP." - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 489
be started to recover the 0xa2 blade." "Blade rebooted during firmwareCommit. The operation will be restarted." 0xa3 "Firmware has been downloaded successfully. Blade is rebooting with the new firmware." 0xa4 "Blade has rebooted successfully." 0xa5 "New firmware failed to boot up. Please retry - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 490
Switch reboots during relocating the AP image. The operation will be restarted." 0xab "Blade of firmware." 0xF "Upgrade is switch is supported by the requested firmware service provider for recovery." 0x13 "Out of memory." 0x14 "Failed to download RPM package." 0x15 "Unable to create firmware - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 491
Device Based Routing policy is not supported by 5.1. Use aptPolicy to change the routing policy before proceeding." 0x2d "Invalid RPM package. Please reload firmware packages on the file server." 0x2e "Cannot downgrade due to presence of blade type 17. Remove or power off these blades before - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 492
may be caused by an unsupported blade type in the chassis. Remove or power off the unsupported blades before proceeding. Another possible cause may networking issues. Please reload firmware packages on the file server, then retry firmwareDownload. If the problem persists, contact your system - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 493
upgrade the firmware on the standby CP to the same version as the active CP. Then retry firmwareDownload to download the desired version of firmware onto the CPs. Refer to the Fabric OS Administrator's Guide for troubleshooting filesystem, contact your switch service provider. Action Severity INFO - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 494
LOADING state, remove and re-insert the blade to trigger another firmwareDownload. If the problem persists, contact your switch service provider. Severity ERROR SULB-1020 Message , [SULB-1020], AUDIT, ERROR, , New firmware failed to boot in slot . Probable - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 495
firmwareDownload command, for example, by powering off and on of the indicated BP blade in the middle of a firmware, firmwareDownload will automatically be restarted on the blade. Run the firmwareDownloadStatus command to monitor the progress. If the problem persists, contact your switch service - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 496
Action command to monitor progress. If the problem persists, contact your switch service provider. Severity WARNING SULB-1031 Message , [SULB-1031], , AUDIT, WARNING, , The switch is relocating an internal firmware image. 444 Fabric OS Message Reference - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 497
by inconsistent internal firmware image. It may also be caused by the internal Ethernet or persistent storage hardware failure. Recommended Reset the switch. This will cause the internal image to be relocated again. If the problem persists, Action contact your switch service provider. Severity - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 498
download and after download of the firmware to store version information. Recommended No action is required. Action Severity INFO SULB-1037 Message , [SULB-1037], , AUDIT, INFO, , HCL failed. Reboot the switch manually using the reboot command. However - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 499
then run the Action supportSave command and contact your switch service provider. Severity ERROR SWCH-1002 Message , [SWCH Brocade 24000 or 48000 switch, run the slotPowerOff command and then the slotPowerOn command. On a Brocade 7500 or AP7600 switch, reboot or power cycle the switch - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 500
a blade has failed during failover or recovery. Recommended Action On a Brocade 24000 or 48000 switch, run the slotPowerOff command and then the slotPowerOn command. On a Brocade 200E, 3250, 3850, 3900, 4012, 4016, 4018, 4020, 4024, 4100, 4900, 5000, 7500, or AP7600 switch, reboot or power cycle - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 501
Probable Cause Indicates that the switch port is disabled due to the reason displayed in the message. Recommended Action Based on the disable reason displayed, blade with ports that support port swap. Then port swap the ports back to ports default area. Refer to the Fabric OS Administrator's Guide - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 502
70 SWCH-1008 450 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 503
more programs to register with system services or to fail over to active status. Recommended Action The switch is in an inconsistent state and can be corrected only by a reboot or power cycle. Before rebooting the chassis, record the firmware version on the switch or control processor (CP) and run - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 504
supported by CP Blade with ID - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 505
Action Run the memShow command to view the switch memory usage. Reboot or power cycle the switch. Run supportFtp as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity CRITICAL SYSM-1002 Message , [SYSM - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 506
is properly seated in its slot. Action Severity CRITICAL SYSM-1006 Message , [SYSM-1006], , FFDC, CRITICAL, , CP blade in slot is incompatible with the chassis type. Probable Cause Indicates that this chassis type is not compatible with the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 507
WATCHDOG EXPIRED generated by hardware watchdog expiration • MANUAL generated by the tracedump -n command Recommended Run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command Action and contact your switch service provider. Severity WARNING TRCE-1002 Message - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 508
persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the Action supportSave command and contact your switch service provider. Severity ERROR TRCE-1004 Message , [TRCE-1004], ,, WARNING, , Trace dump< optional slot indicating on - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 509
of a change in trace status. This message is only applicable to the Brocade 24000, and 48000. Recommended Action This message is often transitory. Wait FTP transfers; then run the supportSave command and contact your switch service provider. Severity ERROR TRCE-1008 Message , [TRCE- - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 510
trace information to active CP. This message is only applicable to the Brocade 24000 and 48000. Recommended Action Run the haShow command to verify switch service provider. Severity ERROR TRCE-1011 Message , [TRCE-1011], ,, INFO, , Trace dump manually - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 511
system and the indicated slot is unavailable. Recommended Check that the AP blade is enabled and retry the command. If the AP blade is already enabled, run Action the supportSave command and contact your switch service provider. Severity WARNING Fabric OS Message Reference 459 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 512
73 TRCE-1012 460 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 513
by an authorized user. If this message occurs repeatedly, it might indicate an unauthorized user trying to gain access to a switch. When Secure mode is enabled on the fabric, the IP address of a failed login is reported to the error log. Severity INFO TRCK-1003 Message , [TRCK-1003 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 514
, , Config file change from task: Probable Cause Indicates that the track change feature recorded a configuration change for the switch. The track change feature records any change to the configuration file in nonvolatile memory, including a configDownload. This message is not - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 515
to verify that the principal or primary FCS switch has the clock server IP configured correctly. Verify that this clock server is accessible to the switch and functional. If the principal or primary FCS does not support the feature, either choose a different switch for the role or reset the clock - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 516
The message might be one of the following: • Init failed. Time Service exiting Probable Cause: Initialization error, Time Server exits. • Synchronizing time or role change of the principal or primary fabric configuration server (FCS) switch. If the message does not recur, it should be ignored. • - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 517
Cause Indicates that there is a change in the source of fabric time synchronization distributed from the principal or primary fabric configuration server (FCS) switch. Another clock server in the list of clock servers configured is being used. This happens when the network time protocol (NTP) query - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 518
75 TS-1008 466 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 519
number>, FFDC, CRITICAL, , Inconsistent route detected: Port = , should be Probable Cause Indicates that the switch detected an inconsistency in the routing database between the routing protocol and the hardware configuration. The first port number displayed - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 520
76 UCST-1020 468 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 521
, [UPTH-1001], ,, WARNING, , No minimum cost path in candidate list Probable Cause Indicates that the specified switch is unreachable because no minimum cost path (FSPF UPATH) exists in the candidate list (domain ID list). Recommended No action is required - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 522
77 UPTH-1001 470 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 523
Chapter WEBD System Messages 78 WEBD-1001 Message , [WEBD-1001], ,, WARNING, , Missing or Invalid Certificate file -- HTTPS is configured to be enabled but could not be started. Probable Cause Indicates that the SSL certificate file is either invalid or - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 524
[WEBD-1007], , FFDC, INFO, , HTTP server will be restarted due to change of IP Address Probable Cause Indicates that the IP address of the switch changed and the HTTP server is restarted. Recommended No action is required. Action Severity INFO 472 Fabric OS Message - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 525
HTTP server cannot be started Probable Cause Indicates a rare error condition, where the built-in recovery process has failed to restore http services. The problem often results from invalid configuration of ssl certs., but there can be more than one reason for such failure. Recommended Run the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 526
78 WEBD-1008 474 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 527
message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command to save these core files and contact your switch service provider. Severity ERROR Fabric OS Message Reference 475 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 528
79 ZOLB-1001 476 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 529
port login (PLOGI) trap processing. This messages usually indicates problems when adding content-addressable memory (CAM) entries before the transfers; then run the Action supportSave command and contact your switch service provider. Severity WARNING ZONE-1003 Message , [ZONE-1003 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 530
using both world-wide name (WWN) in one zone and in another, this will cause that port to go session based hard zoning. In session-based zoning, the zone enforcement is checked by the software. In hardware-enforced zoning, zone or alias members are defined using - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 531
the filter setup. Recommended Action There are two ways to avoid this problem. • Avoid having too many hosts zoned with a set of target • Avoid having too many zones directed at a single port group on the switch. Severity INFO ZONE-1008 Message , [ZONE-1008], ,, - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 532
in the current code release. If the QuickLoop zoning configuration is enabled on the switch, it will not be supported. Recommended Edit the zone database to remove the QuickLoop zoning definition in the effective configuration. Action Severity WARNING 480 Fabric OS Message Reference 53 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 533
Probable Cause Indicates that the required zoning license is missing. Recommended Install the zoning license using the licenseAdd command. Refer to your switch supplier to obtain a Action Zoning license if you do not have one. Severity ERROR ZONE-1015 Message , [ZONE-1015], - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 534
based hard zoning (value = 3) • FA zone (value = 5) QuickLoop zones are not supported in Fabric OS v4.x and above. Recommended If the message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the Action supportSave command and contact your switch service - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 535
, run supportFtp (as needed) to set up automatic FTP transfers; then run the Action supportSave command and contact your switch service provider. Severity INFO ZONE-1024 Message , [ZONE-1024], ,, INFO, , . Probable Cause Indicates - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 536
has exited. • Unknown: An error was received for an unknown reason. • User Command: A user aborted the current zoning transaction. • Switch Shutting Down: The switch is currently shutting down. Recommended Action Many of the causes of this error message are transitory: for example because two - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 537
switches in your fabric. Refer to the Fabric OS Administrator's Guide for information on the zone database sizes supported for each switch automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity WARNING ZONE-1030 Message , [ZONE-1030 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 538
ZONE-1031 Message Probable Cause Recommended Action Severity , [ZONE-1031], ,, ERROR, , Switch is in interop mode. (switch, port) members not supported. The switch is set to interop mode using the interopMode command. Interop mode does not allow - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 539
is not found. Recommended Use the firmwareDownload command to reinstall the firmware. Action Severity WARNING ZONE-1035 Message , [ZONE-1035], the zone configuration is too large for the memory available on the switch. Recommended Reduce the size of the zone database and retry the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 540
the zone configuration is too large for the memory available on the switch. Recommended Reduce the size of the zone database and retry the operation the zone configuration is too large for the memory available on the switch. Recommended Reduce the size of the zone database and retry the operation - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 541
the zone configuration is too large for the memory available on the switch. Recommended Reduce the size of the zone database and retry the number>,, INFO, , The Default Zone access mode is set to No Access. Probable Cause Indicates that the Default Zone access mode is set to No - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 542
Action Severity INFO ZONE-1045 Message , [ZONE-1045], ,, INFO, , The Default Zone access mode is already set to No Access. Probable Cause Indicates that the Default Zone access mode is already set to No Access. Recommended No action is required. Action - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 543
Chapter AUDIT AUTH System Messages 81 AUTH-3001 Message AUDIT, , [AUTH-3001], INFO, SECURITY, , , , Event: , Status: success, Info: type has been changed from [] to []. Probable Cause Indicates - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 544
error might indicate that an invalid entity attempted to connect to the switch. Recommended Action Check the connection port for a possible security attack. ; then run the supportSave command and contact your switch service provider. Severity INFO 492 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 545
message persists, run supportFtp (as needed) to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. Severity INFO AUTH-3008 Message AUDIT, , [AUTH-3008], INFO, SECURITY, , , , Event: - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 546
81 AUTH-3008 494 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 547
Cause The system attempted to download a configuration without disabling the switch was unsuccessful because there are one or more parameters that require the switch to be disabled. Recommended Disable the switch using the switchDisable command and download the configuration. Action Severity - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 548
82 CONF-1022 496 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 549
Chapter AUDIT HTTP System Messages 83 HTTP-1002 Message AUDIT, , [HTTP-1002], INFO, ZONE, , , , Zoning transaction initiated by User: , Role: completed successfully. Probable Cause Indicates that the zoning database has - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 550
83 HTTP-1003 498 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 551
Chapter AUDIT SEC System Messages 84 SEC-3001 Message AUDIT, , [SEC-3001], INFO, SECURITY, , , , Event: , Status: success, Info: Security mode on the fabric. Probable Cause Indicates that the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 552
84 SEC-3003 SEC-3003 Message AUDIT, , [SEC-3003], INFO, SECURITY, , , , Event: , Status: success, Info: Created policy, with member(s) . Probable Cause Indicates that a new security policy was created - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 553
84 SEC-3006 SEC-3006 Message AUDIT, , [SEC-3006], INFO, SECURITY, , , , Event: , Status: success, Info: Removed member(s) from policy . Probable Cause Indicates that a user has removed the specific - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 554
84 SEC-3009 SEC-3009 Message AUDIT, , [SEC-3009], INFO, SECURITY, , , , Event: , Status: success, Info: Security Transaction aborted. Probable Cause Indicates that the pending security transaction was aborted. Recommended Action - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 555
Name>, Status: success, Info: RADIUS server for AAA services. Probable Cause Indicates that a user has changed the remote authentication dial-in user service (RADIUS) configuration. Recommended Action Verify that the RADIUS configuration was changed intentionally. If - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 556
name> to position . Probable Cause Indicates that a user has changed the position of the remote authentication dial-in user service (RADIUS) server. Recommended Action Verify that the RADIUS server position was intentionally changed. If the RADIUS server position was intentionally - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 557
Passwdcfg parameters set to default values. Probable Cause Indicates that the passwdCfg parameters are set to default values. Recommended Action Verify attempt via . Probable Cause Indicates that a successful login occurred. An IP Address is displayed when the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 558
Name>, Status: failed, Info: Failed login attempt via . Probable Cause Indicates that a failed login attempt occurred. Recommended Action Verify has expired or an administrator Action may manually unlock the account. Severity INFO 506 Fabric OS Message Reference - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 559
84 SEC-3024 SEC-3024 Message AUDIT, , [SEC-3024], INFO, SECURITY, , , , Event: , Status: success, Info: User account [], password changed. Probable Cause Indicates that the user's password changed. Recommended Action - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 560
84 SEC-3027 SEC-3027 Message AUDIT, , [SEC-3027], INFO, SECURITY, , , , Event: , Status: success, Info: User account [] []. Probable Cause Indicates that user account properties were changed. - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 561
SEC-3032 Message AUDIT, , [SEC-3032], INFO, SECURITY, , , , Event: , Status: success, Info: Switch is configured to database. Probable Cause Indicates that the specified event has occurred to accept - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 562
[SEC-3036], INFO, SECURITY, , , , Event: ipfilter, Status: failed, Info: Failed to save changes for ipfilter policy(s). Indicates that the specified IP filter policy(ies) have not been saved. 510 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 563
Connection Type>. Probable Cause Indicates that a security violation was reported. The IP address of the unauthorized host is displayed in the message. Recommended Check for unauthorized access to the switch through the specified protocol connection. Take Action appropriate action as defined by - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 564
84 SEC-3044 SEC-3044 Message AUDIT, , [SEC-3044], INFO, SECURITY, , , FIPS mode has been changed to . Probable Cause Indicates that there was a change in the FIPS mode. Recommended Action Verify that the security event was planned. - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 565
84 SEC-3048 Severity INFO SEC-3048 Message AUDIT, , [SEC-3048], INFO, SECURITY, , , FIPS mode has been enabled in the system using force option. Probable Cause Indicates that the system has been forced to FIPS mode. Recommended Action Verify - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 566
84 SEC-3049 514 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 567
Probable Cause Indicates that the simple network management protocol (SNMP) configuration s incorrect and the SNMP service will not work correctly. Recommended Reset the SNMP configuration to default. Action Severity ERROR SNMP-1005 Message Probable Cause AUDIT, , [SNMP-1005], INFO - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 568
85 SNMP-1006 516 Fabric OS Message Reference 53-1000600-01 - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 569
continue without disruption. Do not fail over or power down the system during firmware upgrade. Run the firmwareDownloadStatus command for more information. Severity that the firmwareDownload command has completed successfully and switch firmware has been updated. Recommended Action No action is - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 570
failed on Standby CP." "firmwareCommit failed on Standby CP." "firmwareDownload failed." "firmwareDownload failed due to IPC error." "Unable to check the firmware version on Standby CP due to IPC error." "firmwareDownload failed due to IPC error." "firmwareDownload failed due to IPC error." "Standby - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 571
secondary partition. Please use firmwareDownloadStatus and firmwareShow to see firmware status." "firmwareDownload has started on Standby CP. up." "Standby CP booted up with new firmware." "Standby CP failed to boot up with new firmware." "firmwareDownload has completed successfully on Standby CP." - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 572
be started to recover the 0xa2 blade." "Blade rebooted during firmwareCommit. The operation will be restarted." 0xa3 "Firmware has been downloaded successfully. Blade is rebooting with the new firmware." 0xa4 "Blade has rebooted successfully." 0xa5 "New firmware failed to boot up. Please retry - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 573
Switch reboots during relocating the AP image. The operation will be restarted." 0xab "Blade of firmware." 0xF "Upgrade is switch is supported by the requested firmware service provider for recovery." 0x13 "Out of memory." 0x14 "Failed to download RPM package." 0x15 "Unable to create firmware - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 574
Device Based Routing policy is not supported by 5.1. Use aptPolicy to change the routing policy before proceeding." 0x2d "Invalid RPM package. Please reload firmware packages on the file server." 0x2e "Cannot downgrade due to presence of blade type 17. Remove or power off these blades before - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 575
may be caused by an unsupported blade type in the chassis. Remove or power off the unsupported blades before proceeding. Another possible cause networking issues. Please reload firmware packages on the file server, then retry firmwareDownload. If the problem persists, contact your system - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 576
in LOADING state, remove and re-insert the blade to trigger another firmwareDownload. If the problem persists, contact your switch service provider. Severity ERROR SULB-1018 Message AUDIT, , [SULB-1018], ERROR, FIRMWARE, , , , Firmwaredownload - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 577
blade to trigger another firmwareDownload. If the problem persists, contact your switch service provider. Severity ERROR SULB-1020 Message AUDIT, , [SULB-1020], ERROR, FIRMWARE, , , , New firmware powering off and on of the indicated BP blade - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 578
monitor the progress. If the problem persists, contact your switch service provider. Severity WARNING SULB-1024 Message AUDIT, , [SULB-1024], WARNING, FIRMWARE, , , , Firmware commit has completed on the blade in slot . Probable - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 579
rebooted. Run the firmwareDownloadStatus Action command to monitor progress. If the problem persists, contact your switch service provider. Severity WARNING SULB-1031 Message AUDIT, , [SULB-1032], WARNING, FIRMWARE, , , , Relocating an internal - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 580
to be relocated again. If the problem persists, Action contact your switch service provider. Severity ERROR SULB-1037 Message AUDIT, , [SULB-1037], ERROR, FIRMWARE, , , , HCL failed. Reboot the switch manually using the reboot command. However - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 581
Chapter AUDIT ZONE System Messages 87 ZONE-3001 Message AUDIT, , [ZONE-3001], INFO, ZONE, , , , Event: , Status: success, Info: \"\" added to \" - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 582
87 ZONE-3003 ZONE-3003 Message AUDIT, , [ZONE-3003], INFO, ZONE, , , , Event: , Status: success, Info: \"\" deleted. Probable Cause Indicates that the specified zone object has been deleted. The - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 583
87 ZONE-3006 ZONE-3006 Message AUDIT, , [ZONE-3006], INFO, ZONE, , , , Event: , Status: success, Info: Current zone configuration disabled. . Probable Cause Indicates that the current zone configuration has been disabled. - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 584
87 ZONE-3009 ZONE-3009 Message AUDIT, , [ZONE-3009], INFO, ZONE, , , , Event: , Status: success, Info: . Probable Cause Indicates that the specified zone transaction has been aborted. Recommended Verify that the - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 585
87 ZONE-3012 ZONE-3012 Message AUDIT, , [ZONE-3012], INFO, ZONE, , , , Event: , Status: success, Info: Zone object \"\" renamed to \"\". Probable Cause Indicates that the specified zone object - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 586
87 ZONE-3015 ZONE-3015 Message AUDIT, , [ZONE-3015], INFO, FABRIC, , , , Event: , Status: success, Info: AD configurations applied. Probable Cause Indicates that the current admin domain (AD) configuration has been saved to flash is - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 587
87 ZONE-3018 ZONE-3018 Message AUDIT, , [ZONE-3018], INFO, FABRIC, , , , Event: , Status: success, Info: has been deactivated. Probable Cause Indicates that the specified admin domain (AD) object has been - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 588
87 ZONE-3021 ZONE-3021 Message AUDIT, , [ZONE-3021], INFO, FABRIC, , , , Event: , Status: success, Info: AD object \"\" renamed to \"\". Probable Cause Indicates that the specified admin domain ( - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 589
87 ZONE-3024 ZONE-3024 Message AUDIT, , [ZONE-3024], INFO, FABRIC, , , , Command: , Status: success, Info: executed. . Probable Cause Indicates that the admin domain ad --transabort operation was successful in the specified - HP StorageWorks 4/64 | Brocade Fabric OS Message Reference Supporting Fabric OS - Page 590
87 ZONE-3025 538 Fabric OS Message Reference 53-1000600-01
53-1000600-01
19 October 2007
Fabric OS
Message Reference
Supporting Fabric OS v6.0.0