HP s5160f Upgrade and Service

HP s5160f - Pavilion - Slimline Manual

Get HP s5160f - Pavilion - Slimline PDF manuals and user guides
UPC - 884420975267
View all HP s5160f manuals
Add to My Manuals
Save this manual to your list of manuals

HP s5160f manual content summary:

  • HP s5160f | Upgrade and Service - Page 1
    Printed in Upgrading and Servicing Guide
  • HP s5160f | Upgrade and Service - Page 2
  • HP s5160f | Upgrade and Service - Page 3
    Removing and Replacing the Front Panel
  • HP s5160f | Upgrade and Service - Page 4
    Never open the cover with the power cord attached or power applied. You may damage your computer or be injured from the spinning fan blades. Avoid touching sharp edges inside the computer. NOTE: Computer features may vary by model. 2 If your system has one, remove the HP Pocket Media Drive from the
  • HP s5160f | Upgrade and Service - Page 5
    3 Disconnect all peripherals and cables, including the power cord. 6 Locate the three tabs that secure the front panel to the computer. Pull each of the tabs out slightly, away from the computer, to release the panel. 4 With a screwdriver, loosen the side panel thumbscrew on the back of the
  • HP s5160f | Upgrade and Service - Page 6
    Panel IMPORTANT: The new (replacement) part may not look the same as the original part, due to different manufacturers or models. Hewlett-Packard always provides quality parts that meet or exceed your original computer specifications. 1 Insert the three tabs on the front panel into the slots on the
  • HP s5160f | Upgrade and Service - Page 7
    6 Set the computer upright. 8 Reconnect all peripherals and cables, including the power cord. 7 Tighten the side panel thumbscrew on the back of the computer. 9 Turn on the computer. 537498-001 - Removing and Replacing the Front Panel 5
  • HP s5160f | Upgrade and Service - Page 8
    6 537498-001 - Removing and Replacing the Front Panel
  • HP s5160f | Upgrade and Service - Page 9
    Removing and Replacing the CD/DVD Drive
  • HP s5160f | Upgrade and Service - Page 10
    components. WARNING: Never open the cover with the power cord attached or power applied. You may damage your computer or be injured from the spinning fan blades. Avoid touching sharp edges inside the computer. NOTE: Computer features may vary by model. IMPORTANT: Treat the CD/DVD drive with care
  • HP s5160f | Upgrade and Service - Page 11
    all peripherals and cables, including the power cord. 5 Slide the side cover toward the back of the computer, lift it off, and set it aside. 6 Locate the three tabs that secure the front panel to the computer. Pull each of the tabs out slightly, away from the computer, to release the panel. 4 With
  • HP s5160f | Upgrade and Service - Page 12
    8 Locate the CD/DVD drive inside the computer. 10 Disconnect the cables from the drive: The plugs on the cables are keyed and can be the metal latch that secures the drive in the cage. NOTE: The style of latch may vary by computer model. 1 2 4 537495-001 - Removing and Replacing the CD/DVD Drive
  • HP s5160f | Upgrade and Service - Page 13
    may not look the same as the original part, due to different manufacturers or models. Hewlett-Packard always provides quality parts that meet or exceed your original computer specifications. 1 Insert the replacement drive partway into the computer. 13 Pull the drive completely out the front of the
  • HP s5160f | Upgrade and Service - Page 14
    have three or two cables. 4 Insert the three tabs on the front panel into the slots on the computer. 1 5 Swing the front panel toward the computer, and press it into place. 2 3 Push the drive into the computer until it locks in place. 6 537495-001 - Removing and Replacing the CD/DVD Drive
  • HP s5160f | Upgrade and Service - Page 15
    the bottom of the side panel into the slots in the computer rail, and then swing the panel down onto the computer. 10 Tighten the side panel thumbscrew on the back of the computer. 8 Slide the panel toward the front of the computer until there is no gap. 537495-001 - Removing and Replacing the
  • HP s5160f | Upgrade and Service - Page 16
    11 Reconnect all peripherals and cables, including the power cord. 12 Turn on the computer. 8 537495-001 - Removing and Replacing the CD/DVD Drive
  • HP s5160f | Upgrade and Service - Page 17
    Removing and Replacing the Hard Disk Drive
  • HP s5160f | Upgrade and Service - Page 18
    . NOTE: Computer features may vary by model. Read This First This procedure requires you to remove five screws. Some computer models use two power cord attached or power applied. You may damage your computer or be injured from the spinning fan blades. Avoid touching sharp edges inside the computer
  • HP s5160f | Upgrade and Service - Page 19
    ) for the drive cage inside the computer. Removing the Hard Disk Drive 1 Turn off the computer. Below are the locations of the three long screws (select models) for the drive cage on the front of the computer. 2 If your system has one, remove the HP Pocket Media Drive from the bay. 537496-001
  • HP s5160f | Upgrade and Service - Page 20
    3 Disconnect all peripherals and cables, including the power cord. 6 Locate the three tabs that secure the front panel to the computer. Pull each of the tabs out slightly, away from the computer, to release the panel. 4 With a screwdriver, loosen the side panel thumbscrew on the back of the
  • HP s5160f | Upgrade and Service - Page 21
    8 Locate the CD/DVD drive inside the computer. 10 Disconnect the cables from the drive: The plugs on the cables are keyed and can be metal latch that secures the drive in the cage. NOTE: The style of latch may vary by computer model. 1 2 537496-001 - Removing and Replacing the Hard Disk Drive 5
  • HP s5160f | Upgrade and Service - Page 22
    in the rectangle), not the processor fan to the left (shown with the circle and X). 13 Pull the drive completely out the front of the computer, and then set it aside. 15 Remove the system fan screw. (This is one of the short screws on select models.) 6 537496-001 - Removing and Replacing the
  • HP s5160f | Upgrade and Service - Page 23
    . Without disconnecting the fan, set it aside. 18 Remove the three screws on the front of the computer that secure the drive cage in the computer. (These are long screws.) 1 2 3 17 Remove the screw at the top of the drive cage. (This is one of the short screws on select models.) 19 Remove the
  • HP s5160f | Upgrade and Service - Page 24
    20 Lift the cage all the way out of the computer and set it on its side. 22 Disconnect the cables from the drive: The plugs on the cables are keyed and can be inserted only
  • HP s5160f | Upgrade and Service - Page 25
    replacement) part may not look the same as the original part, due to different manufacturers or models. Hewlett-Packard always provides quality parts that meet or exceed your original computer specifications. 1 Orient the replacement hard disk drive with the label facing up and the connectors facing
  • HP s5160f | Upgrade and Service - Page 26
    (two on each side) that secure the hard disk drive in the cage. 6 Align the drive cage with the opening in the front of the computer, slide the drive cage up to engage the two tabs, circled below, and... 4 Connect the cables to the drive. ...ensure the screw hole at the
  • HP s5160f | Upgrade and Service - Page 27
    one of the short screws on select models. 9 Replace the system fan by inserting the two lower hooks on the fan (1) into the slots in the computer, and then swinging the top of the fan (2) onto the computer. 2 8 Replace the three screws on the front of the computer that secure the drive cage in the
  • HP s5160f | Upgrade and Service - Page 28
    11 Replace the system fan screw. NOTE: This is one of the short screws on select models. 13 Connect the cables to the drive. Your drive may have three or two cables. 1 12 Insert the CD/DVD drive partway into the computer. 2 14 Push the drive into the computer until it locks in place. 12
  • HP s5160f | Upgrade and Service - Page 29
    three tabs on the front panel into the slots on the computer. 18 Insert the bottom of the side panel into the slots in the computer rail, and then swing the panel down onto the computer. 16 Swing the front panel toward the computer, and press it into place. 19 Slide the panel toward
  • HP s5160f | Upgrade and Service - Page 30
    21 Tighten the side panel thumbscrew on the back of the computer. 23 Turn on the computer. 22 Reconnect all peripherals and cables, including the power cord. 14 537496-001 - Removing and Replacing the Hard Disk Drive
  • HP s5160f | Upgrade and Service - Page 31
    Removing and Replacing an Add-in Card
  • HP s5160f | Upgrade and Service - Page 32
    : Never open the cover with the power cord attached or power applied. You may damage your computer or be injured from the spinning fan blades. Avoid touching sharp edges inside the computer. NOTE: Computer features may vary by model. IMPORTANT: Treat any add-in card with care. It is easy to damage
  • HP s5160f | Upgrade and Service - Page 33
    and cables, including the power cord. 5 Slide the side cover toward the back of the computer, lift it off, and set it aside. 6 Lay the computer on its side. 4 With a screwdriver, loosen the side panel thumbscrew on the back of the computer. 7 Locate the add-in card you want to replace, and
  • HP s5160f | Upgrade and Service - Page 34
    from the socket as you lift the card. A release pad must be pushed down as you lift the card. 9 Remove the bracket cover, and set it aside. 11 Remove the card: If there is no release latch, rock the card to free it, and then lift the card from the socket. If there is a release
  • HP s5160f | Upgrade and Service - Page 35
    not look the same as the original part, due to different manufacturers or models. Hewlett-Packard always provides quality parts that meet or exceed your original computer specifications. 1 Connect the cable to the new add-in card (if there was a cable on the one you removed). 2 Align the edge of
  • HP s5160f | Upgrade and Service - Page 36
    on the bracket cover with the slots on the back of the computer and replace the bracket cover. 5 Insert the bottom of the side panel into the slots in the computer rail, and then swing the panel down onto the computer. 4 Insert and tighten the bracket cover screw. 6 Slide the panel toward the
  • HP s5160f | Upgrade and Service - Page 37
    8 Tighten the side panel thumbscrew on the back of the computer. 10 Turn on the computer. 9 Reconnect all peripherals and cables, including the power cord. 537497-001 - Removing and Replacing an Add-in Card 7
  • HP s5160f | Upgrade and Service - Page 38
    8 537497-001 - Removing and Replacing an Add-in Card
  • HP s5160f | Upgrade and Service - Page 39
    Removing and Replacing the System Fan
  • HP s5160f | Upgrade and Service - Page 40
    Never open the cover with the power cord attached or power applied. You may damage your computer or be injured from the spinning fan blades. Avoid touching sharp edges inside the computer. NOTE: Computer features may vary by model. 2 If your system has one, remove the HP Pocket Media Drive from the
  • HP s5160f | Upgrade and Service - Page 41
    all peripherals and cables, including the power cord. 5 Slide the side cover toward the back of the computer, lift it off, and set it aside. 6 Locate the three tabs that secure the front panel to the computer. Pull each of the tabs out slightly, away from the computer, to release the panel. 4 With
  • HP s5160f | Upgrade and Service - Page 42
    10 Push in the metal tab (1) above the fan as you tip out the top of the fan (2), and lift the fan (3) partway out of the computer. 1 2 9 Remove the system fan screw. 3 11 Trace the system fan cable (1) to the motherboard, disconnect it (2), and set the fan aside. Write down where it was connected
  • HP s5160f | Upgrade and Service - Page 43
    same as the original part, due to different manufacturers or models. Hewlett-Packard always provides quality parts that meet or exceed your original computer specifications. 1 Connect the cable for the replacement system fan to the motherboard. 3 Press the fan until the metal tab locks it in place
  • HP s5160f | Upgrade and Service - Page 44
    the three tabs on the front panel into the slots on the computer. 8 Insert the bottom of the side panel into the slots in the computer rail, and then swing the panel down onto the computer. 6 Swing the front panel toward the computer, and press it into place. 9 Slide the panel toward the front
  • HP s5160f | Upgrade and Service - Page 45
    11 Tighten the side panel thumbscrew on the back of the computer. 13 Turn on the computer. 12 Reconnect all peripherals and cables, including the power cord. 537499-001 - Removing and Replacing the System Fan 7
  • HP s5160f | Upgrade and Service - Page 46
    8 537499-001 - Removing and Replacing the System Fan
  • HP s5160f | Upgrade and Service - Page 47
    Removing and Replacing Memory
  • HP s5160f | Upgrade and Service - Page 48
    Memory 30 minutes Before You Begin Use the product specification for your model to find the correct type of DIMM (dual in-line memory module) for your computer and the maximum memory amount. Memory upgrades may not be needed. Many computers already have the maximum amount of memory installed
  • HP s5160f | Upgrade and Service - Page 49
    the Memory Module 1 Turn off the computer. 3 Disconnect all peripherals and cables, including the power cord. 2 If your system has one, remove the HP Pocket Media Drive from the bay. 4 With a screwdriver, loosen the side panel thumbscrew on the back of the computer. 537494-001 - Removing and
  • HP s5160f | Upgrade and Service - Page 50
    , lift it off, and set it aside. 8 Locate the CD/DVD drive inside the computer. 6 Locate the three tabs that secure the front panel to the computer. Pull each of the tabs out slightly, away from the computer, to release the panel. 9 Locate the cables connected to the back of the drive. Your
  • HP s5160f | Upgrade and Service - Page 51
    the metal latch that secures the drive in the cage. NOTE: The style of latch may vary by computer model. 13 Locate the memory sockets on your computer motherboard. The memory sockets in the computer may be paired sets, coded blue and black. The blue sockets are filled first, starting with the
  • HP s5160f | Upgrade and Service - Page 52
    or models. Hewlett-Packard always provides quality parts that meet or exceed your original computer specifications. NOTE: Install the memory modules into the blue sockets first, starting with the largest capacity module placed in the socket closest to the processor on the motherboard. 1 Touching
  • HP s5160f | Upgrade and Service - Page 53
    module down into the socket until the 1 retaining clips at the ends of the socket lock the module into place. 2 6 Push the drive into the computer until it locks in place. 537494-001 - Removing and Replacing Memory 7
  • HP s5160f | Upgrade and Service - Page 54
    three tabs on the front panel into the slots on the computer. 10 Insert the bottom of the side panel into the slots in the computer rail, and then swing the panel down onto the computer. 8 Swing the front panel toward the computer, and press it into place. 11 Slide the panel toward the
  • HP s5160f | Upgrade and Service - Page 55
    13 Tighten the side panel thumbscrew on the back of the computer. 15 Turn on the computer. 14 Reconnect all peripherals and cables, including the power cord. 537494-001 - Removing and Replacing Memory 9
  • HP s5160f | Upgrade and Service - Page 56
    © Copyright 2009 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. Version: 1.0
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Printed in
Upgrading and Servicing Guide