Husqvarna 550 XP G Mark II Owner Manual - Page 11

To mix fuel, Gasoline, Two-stroke oil, To mix gasoline and two-stroke oil, To fill the fuel tank,

Get Husqvarna 550 XP G Mark II PDF manuals and user guides View all Husqvarna 550 XP G Mark II manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

To mix fuel Gasoline • Use good quality unleaded gasoline with a maximum of 10% ethanol contents. CAUTION: Do not use gasoline with an octane grade less than 90 RON/87 AKI. Use of a lower octane grade can cause engine knocking, which causes engine damages. • We recommend that you use gasoline of a higher octane grade for work with continuously high rpm. Two-stroke oil • For best results and performance use Husqvarna two-stroke oil. • If Husqvarna two-stroke oil is not available, use a two-stroke oil of good quality for air-cooled engines. Speak to your servicing dealer to select the correct oil. CAUTION: Do not use two-stroke oil for water-cooled outboard engines, also referred to as outboard oil. Do not use oil for four-stroke engines. To mix gasoline and two-stroke oil Gasoline, liter 5 10 15 20 US gallon 1 2 1/2 5 Two-stroke oil, liter 2% (50:1) 0.10 0.20 0.30 0.40 US fl. oz. 2 ½ 6 ½ 12 ⅞ CAUTION: Small errors can influence the ratio of the mixture drastically when you mix small quantities of fuel. Measure the quantity of oil carefully and make sure that you get the correct mixture. 1. Fill half the quantity of gasoline in a clean container for fuel. 2. Add the full quantity of oil. 3. Shake the fuel mixture. 4. Add the remaining quantity of gasoline to the container. 5. Carefully shake the fuel mixture. CAUTION: Do not mix fuel for more than 1 month at a time. To fill the fuel tank 1. Clean the area around the fuel tank cap. 2. Shake the container and make sure that the fuel is fully mixed. 3. Tighten the fuel tank cap carefully. 4. Move the product 3 m/10 ft or more away from the refueling area and fuel source before starting. Note: To see where the fuel tank is on your product, refer to Product overview on page 2. To do a run-in • During the first 10 hours of operation, do not apply full throttle without load for extended periods. To use the correct chain oil WARNING: Do not use waste oil, which can cause injury to you and the environment. Waste oil also causes damage to the oil pump, the guide bar and the saw chain. 544 - 005 - 10.05.2019 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
To mix fuel
Gasoline
•
Use good quality unleaded gasoline with a maximum
of 10% ethanol contents.
CAUTION:
Do not use gasoline with an
octane grade less than 90 RON/87 AKI.
Use of a lower octane grade can cause
engine knocking, which causes engine
damages.
•
We recommend that you use gasoline of a higher
octane grade for work with continuously high rpm.
Two-stroke oil
•
For best results and performance use Husqvarna
two-stroke oil.
•
If Husqvarna two-stroke oil is not available, use a
two-stroke oil of good quality for air-cooled engines.
Speak to your servicing dealer to select the correct
oil.
CAUTION:
Do not use two-stroke oil for
water-cooled outboard engines, also
referred to as outboard oil. Do not use oil
for four-stroke engines.
To mix gasoline and two-stroke oil
Gasoline, liter
Two-stroke oil,
liter
2% (50:1)
5
0.10
10
0.20
15
0.30
20
0.40
US gallon
US fl. oz.
1
2 ½
2 1/2
6 ½
5
12 ⅞
CAUTION:
Small errors can influence the
ratio of the mixture drastically when you mix
small quantities of fuel. Measure the quantity
of oil carefully and make sure that you get
the correct mixture.
1.
Fill half the quantity of gasoline in a clean container
for fuel.
2.
Add the full quantity of oil.
3.
Shake the fuel mixture.
4.
Add the remaining quantity of gasoline to the
container.
5.
Carefully shake the fuel mixture.
CAUTION:
Do not mix fuel for more than 1
month at a time.
To fill the fuel tank
1.
Clean the area around the fuel tank cap.
2.
Shake the container and make sure that the fuel is
fully mixed.
3.
Tighten the fuel tank cap carefully.
4.
Move the product 3 m/10 ft or more away from the
refueling area and fuel source before starting.
Note:
To see where the fuel tank is on your product,
refer to
Product overview on page 2
.
To do a run-in
•
During the first 10 hours of operation, do not apply
full throttle without load for extended periods.
To use the correct chain oil
WARNING:
Do not use waste oil, which can
cause injury to you and the environment.
Waste oil also causes damage to the oil
pump, the guide bar and the saw chain.
544 - 005 - 10.05.2019
11