Husqvarna AUTOMOWER 115H 4G Owner Manual - Page 3

Adjusting The Robotic Lawnmower To Suit The Size Of Your Lawn

Get Husqvarna AUTOMOWER 115H 4G PDF manuals and user guides View all Husqvarna AUTOMOWER 115H 4G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

For more information and instructions, read the complete Operator's manual on the Husqvarna website (www.husqvarna.com). 1. PLACEMENT OF AND CONNECTING THE CHARGING STATION EN 1. Place the charging station with a lot of open space in front of the charging station and on a relatively horizontal surface. 2. Connect the power supply's low voltage cable to the charging station and the power supply. 3. Connect the power supply to a 100-240 V wall socket. 4. Place the robotic lawnmower in the charging station to charge the battery while the boundary wire is laid. Press the ON/OFF button to turn the product on. 2. PLACEMENT OF THE BOUNDARY WIRE AND THE GUIDE WIRE 1. Lay the boundary wire so that it forms a loop around the work area. 2. Make an eyelet at the point where the guide wire will later be connected. 3. Run the guide wire to the point on the boundary loop where the connection will be made. Avoid laying the wire at tight angles. 3. CONNECTING THE BOUNDARY WIRE AND THE GUIDE WIRE 1. Narrow passages in the garden make it difficult for the robotic lawnmower to find the charging station. The robotic lawnmower can be lead to remote garden areas using the guide wire. The guide wire also helps the robotic lawnmower to quickly find the charging station. 2. Lay the guide wire under the charging station and at least 1 m / 3.3 ft straight out from the front edge of the charging station. 3. Open the connectors and lay the wire ends in the recesses on each connector. 4. Press the connectors together using a pair of pliers. 5. Cut off any surplus boundary wire. Cut 1-2 cm / 0.4-0.8 " above the connectors. 6. P ress the boundary connectors onto the contact pins, marked L (left) and R (right), on the charging station. It is important that the right-hand wire is connected to the right-hand contact pin, and the left-hand wire to the left-hand pin. 7. Fasten the guide connector to the contact pin marked G on the charging station. 4. CONNECTING THE GUIDE WIRE TO THE BOUNDARY WIRE 1. Cut the boundary wire with a wire cutters at the centre of the eyelet that was made in step 2.2. 2. Connect the guide wire to the boundary wire using the accompanying couplers. Press the couplers completely together with a pair of pliers. STARTING AND STOPPING STARTING 1. Open the hatch to the keypad. 2.Push the ON/OFF button. The display is lit up. 3.Use the up/down arrow buttons and the OK button to enter the PIN code. Close the hatch. STOPPING Press the STOP button. ADJUSTING THE ROBOTIC LAWNMOWER TO SUIT THE SIZE OF YOUR LAWN The mowing results depend on mowing time. Adjust the mowing time to suit your garden using the Schedule function. You decide what times during the day the robotic lawnmower is to work. The robotic lawnmower mows about 67 m² per hour and day. For example; if your garden consists of 1000 m² of grass, the robotic lawnmower should work on average 15 hours per day. MAINTENANCE 1. Turn off the product during all work on the product, such as cleaning or replacing the blades. Check that the indicator lamp on the ON/OFF button is not lit. 2. Never use a high-pressure washer to clean the robotic lawnmower. Never use solvents for cleaning. 3. All connections to the charging station (power supply, boundary and guide wire) must be disconnected if there is a risk of a thunderstorm. 4. Fully charge the battery at the end of the season before winter storage. P03_QG_1140740-49_115H_US.indd 3 2018-12-12 15:52:25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
For more information and instructions, read the complete Operator’s manual on the Husqvarna
website (www.husqvarna.com).
1. PLACEMENT OF AND CONNECTING THE CHARGING STATION
1. Place the charging station with a lot of open space in front of the charging station and on a relatively horizontal surface.
2. Connect the power supply’s low voltage cable to the charging station and the power supply.
3. Connect the power supply to a 100-240 V wall socket.
4. Place the robotic lawnmower in the charging station to charge the battery while the boundary wire is laid. Press the ON/OFF
button to turn the product on.
2. PLACEMENT OF THE BOUNDARY WIRE AND THE GUIDE WIRE
1. Lay the boundary wire so that it forms a loop around the work area.
2. Make an eyelet at the point where the guide wire will later be connected.
3. Run the guide wire to the point on the boundary loop where the connection will be made. Avoid laying the wire at tight angles.
3. CONNECTING THE BOUNDARY WIRE AND THE GUIDE WIRE
1.
Narrow passages in the garden make it difficult for the robotic lawnmower to find the charging station. The robotic
lawnmower can be lead to remote garden areas using the guide wire. The guide wire also helps the robotic lawnmower to
quickly find the charging station.
2. Lay the guide wire under the charging station and at least 1 m / 3.3 ft straight out from the front edge of the charging station.
3. Open the connectors and lay the wire ends in the recesses on each connector.
4. Press the connectors together using a pair of pliers.
5. Cut off any surplus boundary wire. Cut 1-2 cm / 0.4-0.8 ” above the connectors.
6. Press the boundary connectors onto the contact pins, marked L (left) and R (right), on the charging station. It is important
that the right-hand wire is connected to the right-hand contact pin, and the left-hand wire to the left-hand pin.
7. Fasten the guide connector to the contact pin marked G on the charging station.
4. CONNECTING THE GUIDE WIRE TO THE BOUNDARY WIRE
1. Cut the boundary wire with a wire cutters at the centre of the eyelet that was made in step 2.2.
2. Connect the guide wire to the boundary wire using the accompanying couplers. Press the couplers completely together with
a pair of pliers.
STARTING AND STOPPING
STARTING
1. Open the hatch to the keypad.
2. Push the
ON/OFF
button. The display is lit up.
3. Use the
up/down arrow buttons
and the
OK
button to enter the PIN code. Close the hatch.
STOPPING
Press the
STOP
button.
ADJUSTING THE ROBOTIC LAWNMOWER TO SUIT THE SIZE OF YOUR LAWN
The mowing results depend on mowing time. Adjust the mowing time to suit your garden using the Schedule function. You
decide what times during the day the robotic lawnmower is to work. The robotic lawnmower mows about 67 m² per hour and
day. For example; if your garden consists of 1000 m² of grass, the robotic lawnmower should work on average 15 hours per
day.
MAINTENANCE
1.
Turn off the product during all work on the product, such as cleaning or replacing the blades. Check that the indicator lamp
on the
ON/OFF
button is not lit.
2. Never use a high-pressure washer to clean the robotic lawnmower. Never use solvents for cleaning.
3. All connections to the charging station (power supply, boundary and guide wire) must be disconnected if there is a risk of a
thunderstorm.
4. Fully charge the battery at the end of the season before winter storage.
EN
P03_QG_1140740-49_115H_US.indd
3
2018-12-12
15:52:25