Husqvarna AUTOMOWER 450X EPOS Owner Manual - Page 29

Alarm! Mower outside Geo, Alarm! Mower stopped

Get Husqvarna AUTOMOWER 450X EPOS PDF manuals and user guides View all Husqvarna AUTOMOWER 450X EPOS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Message Wheel motor blocked right/ left Alarm! Mower stopped Alarm! Mower outside Geofence Alarm! Mower was moved Electronic problem Loop sensor problem Tilt sensor problem Temporary problem Invalid sub-device combination Temporary battery problem Faulty mix of batteries Collision sensor problem Lift sensor problem Charging system problem Battery problem Battery temperature outside limits Charging current too high Cause Action The wheel is blocked by grass or other objects. Examine the wheel and remove grass or other objects. The alarm was started because the product was stopped. Alarm was started because the product was moved out of the GeoFence area. Adjust the security settings in the Security menu. Refer to Security (Bluetooth® only) on page 20. The alarm was started because the product was moved. Temporary electronic or firmware prob- Restart the product. If the problem stays, lem in the product. speak to your approved servicing dealer. There is corrosion or dirt on the charging Restart the product. Clean the charging plates and contact plates. plates on the product and the contact plates on the charging station. Temporary electronic or firmware prob- Restart the product. If the problem stays, lem in the product. speak to your approved servicing dealer. Temporary battery or firmware problem Restart the product. If the problem stays, in the product. speak to your approved servicing dealer. Incorrect type of battery. Use only original batteries recommended by the manufacturer. The product cannot start because the temperature in the battery is too high or too low. The product will start to operate when the temperature of the battery has decreased. Make sure that the charging station is put in an area with protection from the sun. Incorrect or defective power supply unit. Examine that the power supply unit and charging station are not defective. Make sure that you use the correct power supply unit and charging station. Restart the product. If the problem stays, speak to your approved servicing dealer. 1970 - 001 - 10.10.2022 Troubleshooting - 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
Message
Cause
Action
Wheel motor blocked right/
left
The wheel is blocked by grass or other
objects.
Examine the wheel and remove grass or
other objects.
Alarm! Mower stopped
The alarm was started because the prod-
uct was stopped.
Adjust the security settings in the
Secur-
ity
menu. Refer to
Security (Bluetooth
®
only) on page 20
.
Alarm! Mower outside Geo-
fence
Alarm was started because the product
was moved out of the GeoFence area.
Alarm! Mower was moved
The alarm was started because the prod-
uct was moved.
Electronic problem
Temporary electronic or firmware prob-
lem in the product.
Restart the product. If the problem stays,
speak to your approved servicing dealer.
Loop sensor problem
Tilt sensor problem
Temporary problem
Invalid sub-device combina-
tion
Temporary battery problem
Faulty mix of batteries
Collision sensor problem
Lift sensor problem
Charging system problem
There is corrosion or dirt on the charging
plates and contact plates.
Restart the product. Clean the charging
plates on the product and the contact
plates on the charging station.
Temporary electronic or firmware prob-
lem in the product.
Restart the product. If the problem stays,
speak to your approved servicing dealer.
Battery problem
Temporary battery or firmware problem
in the product.
Restart the product. If the problem stays,
speak to your approved servicing dealer.
Incorrect type of battery.
Use only original batteries recommended
by the manufacturer.
Battery temperature outside
limits
The product cannot start because the
temperature in the battery is too high or
too low.
The product will start to operate when
the temperature of the battery has de-
creased. Make sure that the charging
station is put in an area with protection
from the sun.
Charging current too high
Incorrect or defective power supply unit.
Examine that the power supply unit and
charging station are not defective. Make
sure that you use the correct power sup-
ply unit and charging station. Restart the
product. If the problem stays, speak to
your approved servicing dealer.
1970 - 001 - 10.10.2022
Troubleshooting -
29