IBM 8676 Option Installation Guide - Page 39

Completing the installation, Installing the cover and bezel, Hardware Maintenance

Get IBM 8676 - Eserver xSeries 335 PDF manuals and user guides
UPC - 087944770107
View all IBM 8676 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Note: The fan LEDs are lit by the Light Path Diagnostics™ circuitry. For more information about the LEDs and the Light Path Diagnostics circuitry, see the section about Light Path Diagnostics in the Hardware Maintenance Manual and Troubleshooting Guide. 5. Remove the fan from the server: a. Disconnect the fan cable from the system board. b. Lift the fan out of the server. Airflow 6. Position the replacement fan so that the airflow arrow on the side of the fan is facing or pointing toward the rear of the server. Note: Correct airflow is from the front to the rear of the server. 7. Position the replacement fan in the location from which you removed the failed fan. 8. Connect the replacement fan cable to the system board. 9. Continue with "Completing the installation". Completing the installation This section describes how to complete the installation. Installing the cover and bezel Complete the following steps to install the server cover and bezel: 1. Position the internal cables so they do not interfere with the cover installation. Attention: Before sliding the cover forward, make sure that all the tabs on both the front and rear of the cover engage the chassis correctly. If all the tabs do not engage the chassis correctly, it will be very difficult to remove the cover later. 2. Position the cover on top of the server and slide it forward. Press down on the cover latch. The cover slides forward into position. Ensure that the cover Chapter 2. Installing options 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
Note:
The fan LEDs are lit by the Light Path Diagnostics
™
circuitry. For more
information about the LEDs and the Light Path Diagnostics circuitry, see
the section about Light Path Diagnostics in the
Hardware Maintenance
Manual and Troubleshooting Guide
.
5.
Remove the fan from the server:
a.
Disconnect the fan cable from the system board.
b.
Lift the fan out of the server.
Airflow
6.
Position the replacement fan so that the airflow arrow on the side of the fan is
facing or pointing toward the rear of the server.
Note:
Correct airflow is from the front to the rear of the server.
7.
Position the replacement fan in the location from which you removed the failed
fan.
8.
Connect the replacement fan cable to the system board.
9.
Continue with “Completing the installation”.
Completing the installation
This section describes how to complete the installation.
Installing the cover and bezel
Complete the following steps to install the server cover and bezel:
1.
Position the internal cables so they do not interfere with the cover installation.
Attention:
Before sliding the cover forward, make sure that all the tabs on
both the front and rear of the cover engage the chassis correctly. If all the tabs
do not engage the chassis correctly, it will be very difficult to remove the cover
later.
2.
Position the cover on top of the server and slide it forward. Press down on the
cover latch. The cover slides forward into position. Ensure that the cover
Chapter 2. Installing options
27