Icom IC-M400BB Instruction Manual

Icom IC-M400BB Manual

Get Icom IC-M400BB PDF manuals and user guides View all Icom IC-M400BB manuals
Add to My Manuals
Save this manual to your list of manuals

Icom IC-M400BB manual content summary:

  • Icom IC-M400BB | Instruction Manual - Page 1
    INSTRUCTION MANUAL VHF MARINE TRANSCEIVER iM400BB This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. COMMANDMICIV™ (HM-195) may not be supplied, depending on the transceiver version.
  • Icom IC-M400BB | Instruction Manual - Page 2
    carefully and completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL - This in- struction manual contains important operating instructions for the IC-M400BB. EXPLICIT DEFINITIONS WORD RWARNING! CAUTION NOTE DEFINITION Personal injury, fire hazard or electric shock may occur
  • Icom IC-M400BB | Instruction Manual - Page 3
    that antenna of a maximum gain of 3 dB are used. If higher gain antenna are required then please contact your Icom distributor for revised installation recommendations. Operation: The exposure to RF electromagnetic field is only applicable when this device is transmitting. This exposure is naturally
  • Icom IC-M400BB | Instruction Manual - Page 4
    RADIO OPERATOR WARNING Icom requires the radio operator to meet the FCC and IC Requirements for Radio Frequency Exposure. An omnidirectional antenna to avoid RF exposure higher than the allowable MPE level set by FCC and IC. iii FAILURE TO OBSERVE THESE LIMITS MAY ALLOW THOSE WITHIN THE MPE RADIUS
  • Icom IC-M400BB | Instruction Manual - Page 5
    POUR LES OPÉRATEURS RADIO Icom exige que l'opérateur radio se conforme aux exigences de la FCC et d'IC en matière d'exposition aux BULLETIN OET 65 DE LA FCC. CETTE DISTANCE ESTIMÉE TIENT COMPTE D'UN SYSTÈME INSTALLÉ SUR UN NAVIRE UTILISANT LA PUISSANCE MAXIMALE DE LA RADIO ET DES ANTENNES DONT LE
  • Icom IC-M400BB | Instruction Manual - Page 6
    in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
  • Icom IC-M400BB | Instruction Manual - Page 7
    only CAUTION: Changes or modifications to this device, not expressly approved by Icom Inc., could void your authority to operate this device under FCC regulations. Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom
  • Icom IC-M400BB | Instruction Manual - Page 8
    IMPORTANT i EXPLICIT DEFINITIONS i IN CASE OF EMERGENCY ii INSTALLATION NOTE ii RADIO OPERATOR WARNING iii AVERTISSEMENT POUR LES OPÉ Cleaning 8 vii ■■Mounting the transceiver 8 ■■ Antenna 8 ■■Microphone installation 9 5 SPECIFICATIONS AND OPTIONS 11-12 ■■ Specifications 11 ■■ Options
  • Icom IC-M400BB | Instruction Manual - Page 9
    11 be thoroughly acquainted with all pertinent rules and regula- 12 tions. 13 14 NOTE: Even though the transceiver is capable of opera- tion on VHF marine channels 3, 21, 23, 61, 64, 81, 82 and 15 83, according to FCC regulations these simplex channels 16 cannot be lawfully used by the
  • Icom IC-M400BB | Instruction Manual - Page 10
    2 PREPARATION ■■MMSI code programming The 9 digit MMSI (Maritime Mobile Service Identity: DSC self ID) code can be programmed at power ON. The code is programmed by using the HM-195. This initial code setting can
  • Icom IC-M400BB | Instruction Manual - Page 11
    PREPARATION 2 ■■ATIS code programming (For Dutch version transceivers) 1 The 10 digit ATIS (Automatic Transmitter Identification System) code can be programmed at power ON. 2 rrRepeat step e to enter all 10 digits. ttAfter entering the 10 digit code, "FINISH" is automatically 3 The code is
  • Icom IC-M400BB | Instruction Manual - Page 12
    . To ensure correct operation of the DSC function, make sure you correctly set the CH70 SQL LEVEL. See (¤5) of the HM-195 instruction manual. Step 1: Transponder's operation qqSelect a desired AIS target on the plotter, target list or dan- ger list display. • Y ou can also go to the next
  • Icom IC-M400BB | Instruction Manual - Page 13
    AIS TRANSPONDER 3 rrAfter making the individual DSC call, the transponder will display "DSC Transmission COMPLETED." • Push [CLEAR] to return to the screen displayed before you entered the voice channel selection screen in step w. • T he transceiver stands by on Channel 70 until an
  • Icom IC-M400BB | Instruction Manual - Page 14
    ANTENNA CONNECTOR Connects to a marine VHF antenna cable's PL-259 con- nector equipment, to receive position data from other ships. White: Talker A (Data-H) Connects to an NMEA LEADS Orange: Public Address Speaker (+) Gray: Public Address Speaker (-) Connects to a PA speaker. • PA output power
  • Icom IC-M400BB | Instruction Manual - Page 15
    cable, NMEA leads, external speaker leads and PA speaker leads, cover the HM-195. 5 NOTE: For those who purchased the IC-M400BB and HM-195 separately. 6 When connecting the HM-195 of the OPC-2014. • Talker A (Data-H) lead (White): Connects to lead 5 of the OPC-2014. • Talker B (Data-L)
  • Icom IC-M400BB | Instruction Manual - Page 16
    Flat washers (M5) Spring washers (M5) Screws (5×20 mm) ■■Fuse replacement One fuse is installed in the supplied DC power cable. If the fuse blows or the transceiver stops functioning, track down the source of the problem, repair it, and replace the damaged fuse with a new one of the proper rating
  • Icom IC-M400BB | Instruction Manual - Page 17
    qqInsert the OPC-1540 cable connector into the command microphone jack, and tighten the nut. wwTo use the cable connector as a wall socket, install it as described to the right. 1 eeUsing the mounting base as a template, carefully mark the 2 holes where the cable and three screws will be
  • Icom IC-M400BB | Instruction Manual - Page 18
    4 CONNECTIONS AND MAINTENANCE Mounting base Gasket Nut Cap 10
  • Icom IC-M400BB | Instruction Manual - Page 19
    5 SPECIFICATIONS AND OPTIONS ■■Specifications DDGeneral • Frequency coverage European versions USA versions • Mode • Channel spacing • Operating temp. range • Current drain (at 13.8 V) • Power supply requirement • Frequency stability • Antenna impedance • Dimensions (approximately) (
  • Icom IC-M400BB | Instruction Manual - Page 20
    ™ External microphone-type controller. 6 m (20 ft) microphone cable included. Black and white colors are Icom optional equipment is designed for optimal performance when used with an Icom transceiver. Icom is not responsible for the destruction or damage to an Icom transceiver in the event the Icom
  • Icom IC-M400BB | Instruction Manual - Page 21
    does not exceed 1 W, and are subject to the national regulations of the administration concerned when these channels are used in its territorial 11 waters. 12 *3 UK Marina Channels: M1=37A (157.850 MHz), M2=P4 (161.425 MHz) for U.K. version only *4 The output power of channels 75 and 76 are
  • Icom IC-M400BB | Instruction Manual - Page 22
    6 CHANNEL LIST • USA channels Channel number Frequency (MHz) Channel number Frequency (MHz) Channel number Frequency (MHz) Channel number Frequency (MHz) USA INT CAN Transmit Receive USA INT CAN Transmit Receive USA INT CAN Transmit Receive USA INT CAN Transmit Receive 01 01 156.050 160.650 21
  • Icom IC-M400BB | Instruction Manual - Page 23
    7 TROUBLE SHOOTING PROBLEM POSSIBLE CAUSE SOLUTION REF. point. ⁄1* 3 from the speaker. • Volume level is set too low. • Set the volume to a suitable level. ⁄0* 4 • Speaker has been exposed to water. 12 * Refer to the HM-195 commandmiciv™ instruction manual. 13 14 15 16 15
  • Icom IC-M400BB | Instruction Manual - Page 24
    < Intended Country of Use > AT BE CY CZ DK EE FI FR DE GR HU IE IT LV LT LU MT NL PL PT SK SI ES SE GB IS LI NO CH BG RO TR HR A-7055D-1EX-q Printed in Japan © 2012-2013 Icom Inc. Printed on recycled paper with soy ink. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
INSTRUCTION MANUAL
iM400BB
VHF MARINE TRANSCEIVER
This device complies with Part 15 of the FCC Rules. Opera-
tion is subject to the condition that this device does not cause
harmful interference.
COMMANDMIC
IV
™ (HM-195)
may not be supplied, depending
on the transceiver version.