Icom IC-M400BB Instruction Manual - Page 10

Preparation

Get Icom IC-M400BB PDF manuals and user guides View all Icom IC-M400BB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

2 PREPARATION ■■MMSI code programming The 9 digit MMSI (Maritime Mobile Service Identity: DSC self ID) code can be programmed at power ON. The code is programmed by using the HM-195. This initial code setting can be performed only once. After being set, it can be changed by only your dealer or distributor. If your MMSI code has already been programmed, this programming is not necessary. qqHold down [PWR](Dial) to turn ON the power. • Three short beeps sound, and "NO DSC MMSI" is displayed. wwPush [ENT] to start the MMSI code programming. • Push [CLEAR] twice to cancel the programming, and go to the normal operating screen. In this case, the transceiver cannot make a DSC call. To program the MMSI code, turn OFF the power, then turn it ON again. eeEnter your MMSI code in the following manner: • Select a desired number using Dial, or Push [ENT] or Dial to set it. • T o move the cursor, select either arrow, "←" or "→," then push [ENT] or Dial. 2 rrRepeat step e to enter all 9 digits. ttAfter entering the 9 digit code, "FINISH" is automatically selected, and then push [ENT] or Dial to set it. yyThe "MMSI CONFIRMATION" screen is displayed. uuEnter your MMSI code again for confirmation. • Enter in the same manner as steps e through t. iiWhen your MMSI code programming is successfully completed, the screen as shown below is briefly displayed. • After that, the normal operating screen is displayed. The programmed MMSI code can be checked in the MENU screen. NOTE: Depending on the transceiver version, the ATIS code programming may be required after programming the MMSI code. See the next page for details.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
2
PREPARATION
2
MMSI code programming
■
The 9 digit MMSI (Maritime Mobile Service Identity: DSC self
ID) code can be programmed at power ON.
The code is programmed by using the HM-195.
This initial code setting can be performed only once.
After being set, it can be changed by only your dealer
or distributor. If your MMSI code has already been pro-
grammed, this programming is not necessary.
Hold down [PWR](Dial) to turn ON the power.
q
• Three short beeps sound, and “NO DSC MMSI” is displayed.
Push [ENT] to start the MMSI code programming.
w
• Push [CLEAR] twice to cancel the programming, and go to the
normal operating screen. In this case, the transceiver cannot
make a DSC call. To program the MMSI code, turn OFF the
power, then turn it ON again.
Enter your MMSI code in the following manner:
e
• Select a desired number using Dial, or [
∫
]/[
√
]/[
Ω
]/[
≈
].
• Push [ENT] or Dial to set it.
•To move the cursor, select either arrow, “
←
” or “
→
,” then push
[ENT] or Dial.
Repeat step
r
e
to enter all 9 digits.
After entering the 9 digit code, “FINISH” is automatically
t
selected, and then push [ENT] or Dial to set it.
The “MMSI CONFIRMATION” screen is displayed.
y
Enter your MMSI code again for confirmation.
u
• Enter in the same manner as steps
e
through
t
.
When your MMSI code programming is successfully com-
i
pleted, the screen as shown below is briefly displayed.
• After that, the normal operating screen is displayed.
The programmed MMSI code can be checked in the MENU
screen.
NOTE:
Depending on the transceiver version, the ATIS
code programming may be required after programming the
MMSI code. See the next page for details.