Intel D915PSY Product Specification - Page 75

Front Panel USB Connectors, INTEGRATOR'S NOTES

Get Intel D915PSY PDF manuals and user guides View all Intel D915PSY manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

Technical Reference 2.8.2.5.2 Reset Switch Connector [Purple] Pins 5 and 7 [Purple] can be connected to a momentary single pole, single throw (SPST) type switch that is normally open. When the switch is closed, the board resets and runs the POST. 2.8.2.5.3 Power/Sleep LED Connector [Green] Pins 2 and 4 [Green] can be connected to a one- or two-color LED. Table 35 shows the possible states for a one-color LED. Table 36 shows the possible states for a two-color LED. Table 35. States for a One-Color Power LED LED State Off Steady Green Description Power off/sleeping Running Table 36. States for a Two-Color Power LED LED State Off Steady Green Steady Yellow Description Power off Running Sleeping ✏ NOTE The colors listed in Table 35 and Table 36 are suggested colors only. Actual LED colors are product- or customer-specific. 2.8.2.5.4 Power Switch Connector [Red] Pins 6 and 8 [Red] can be connected to a front panel momentary-contact power switch. The switch must pull the SW_ON# pin to ground for at least 50 ms to signal the power supply to switch on or off. (The time requirement is due to internal debounce circuitry on the board.) At least two seconds must pass before the power supply will recognize another on/off signal. 2.8.2.6 Front Panel USB Connectors Figure 21 is a connection diagram for the front panel USB connectors. # INTEGRATOR'S NOTES • The +5 V DC power on the USB connector is fused. • Pins 1, 3, 5, and 7 comprise one USB port. • Pins 2, 4, 6, and 8 comprise one USB port. • Use only a front panel USB connector that conforms to the USB 2.0 specification for high- speed USB devices. 75

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
Technical Reference
2.8.2.5.2
Reset Switch Connector [Purple]
Pins 5 and 7 [Purple] can be connected to a momentary single pole, single throw (SPST) type
switch that is normally open.
When the switch is closed, the board resets and runs the POST.
2.8.2.5.3
Power/Sleep LED Connector [Green]
Pins 2 and 4 [Green] can be connected to a one- or two-color LED.
Table 35 shows the possible
states for a one-color LED.
Table 36 shows the possible states for a two-color LED.
Table 35.
States for a One-Color Power LED
LED State
Description
Off
Power off/sleeping
Steady Green
Running
Table 36.
States for a Two-Color Power LED
LED State
Description
Off
Power off
Steady Green
Running
Steady Yellow
Sleeping
✏
NOTE
The colors listed in Table 35 and Table 36 are suggested colors only.
Actual LED colors are
product- or customer-specific.
2.8.2.5.4
Power Switch Connector [Red]
Pins 6 and 8 [Red] can be connected to a front panel momentary-contact power switch.
The switch
must pull the SW_ON# pin to ground for at least 50 ms to signal the power supply to switch on or
off.
(The time requirement is due to internal debounce circuitry on the board.)
At least two
seconds must pass before the power supply will recognize another on/off signal.
2.8.2.6
Front Panel USB Connectors
Figure 21 is a connection diagram for the front panel USB connectors.
INTEGRATOR’S NOTES
•
The +5 V DC power on the USB connector is fused.
•
Pins 1, 3, 5, and 7 comprise one USB port.
•
Pins 2, 4, 6, and 8 comprise one USB port.
•
Use only a front panel USB connector that conforms to the USB 2.0 specification for high-
speed USB devices.
75