Intel D915PSY Product Specification - Page 82

Fan Connector Current Capability, Power Supply Considerations

Get Intel D915PSY PDF manuals and user guides View all Intel D915PSY manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

Intel Desktop Board D915PGN/D915PSY Technical Product Specification 2.11.3 Fan Connector Current Capability CAUTION The processor fan must be connected to the processor fan connector, not to a chassis fan connector. Connecting the processor fan to a chassis fan connector may result in onboard component damage that will halt fan operation. Table 39 lists the current capability of the fan connectors. Table 39. Fan Connector Current Capability Fan Connector Processor fan Front chassis fan Rear chassis fan Rear chassis fan 2 ATX fan (optional) Maximum Available Current 1000 mA 600 mA 600 mA 600 mA 600 mA ✏ NOTE The rear chassis fan 2 is available only on the D915PGN board. It is not available on the D915PSY board. 2.11.4 Power Supply Considerations CAUTION The +5 V standby line for the power supply must be capable of providing adequate +5 V standby current. Failure to do so can damage the power supply. The total amount of standby current required depends on the wake devices supported and manufacturing options. System integrators should refer to the power usage values listed in Table 38 when selecting a power supply for use with the board. Additional power required will depend on configurations chosen by the integrator. The power supply must comply with the following recommendations found in the indicated sections of the ATX form factor specification. • The potential relation between 3.3 VDC and +5 VDC power rails (Section 4.2) • The current capability of the +5 VSB line (Section 4.2.1.2) • All timing parameters (Section 4.2.1.3) • All voltage tolerances (Section 4.2.2) 82

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
Intel Desktop Board D915PGN/D915PSY Technical Product Specification
2.11.3
Fan Connector Current Capability
CAUTION
The processor fan must be connected to the processor fan connector, not to a chassis fan
connector.
Connecting the processor fan to a chassis fan connector may result in onboard
component damage that will halt fan operation.
Table 39 lists the current capability of the fan connectors.
Table 39.
Fan Connector Current Capability
Fan Connector
Maximum Available Current
Processor fan
1000 mA
Front chassis fan
600 mA
Rear chassis fan
600 mA
Rear chassis fan 2
600 mA
ATX fan (optional)
600 mA
✏
NOTE
The rear chassis fan 2 is available only on the D915PGN board.
It is not available on the
D915PSY board.
2.11.4
Power Supply Considerations
CAUTION
The +5 V standby line for the power supply must be capable of providing adequate +5 V standby
current.
Failure to do so can damage the power supply.
The total amount of standby current
required depends on the wake devices supported and manufacturing options.
System integrators should refer to the power usage values listed in Table 38 when selecting a power
supply for use with the board.
Additional power required will depend on configurations chosen by the integrator.
The power supply must comply with the following recommendations found in the indicated
sections of the ATX form factor specification.
•
The potential relation between 3.3 VDC and +5 VDC power rails (Section 4.2)
•
The current capability of the +5 VSB line (Section 4.2.1.2)
•
All timing parameters (Section 4.2.1.3)
•
All voltage tolerances (Section 4.2.2)
82