JVC DF450 Instructions - Page 55

Insert Editing

Get JVC DF450 - Camcorder - 680 KP PDF manuals and user guides View all JVC DF450 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Insert Editing You can record a new scene into a previously recorded tape, replacing a section of the original recording with minimal picture distortion at the in and out points. The original audio remains unchanged. ● Use the provided remote control. NOTES: ● Before performing the following steps, make sure that "TIME CODE" for "CAMERA DISPLAY" and "VIDEO DISPLAY" is set to "ON". (੬ pg. 36, 39, 41) ● Insert Editing is not possible on a tape recorded in the LP mode or on a blank portion of a tape. 1 Play back the tape, locate the Edit-Out point and press PAUSE (9). Memorize the time code at this point (੬ pg. 21) since it will be needed to stop editing in step 5. 2 Press REW (3) until the Edit-In point is located, then press PAUSE (9). 3 Press and hold INSERT (I) on the remote control, then press PAUSE (9). The "9I" indicator and the Time Code (min.:sec.) appear and the camcorder enters Insert-Pause mode. 4 Press START/STOP to begin editing. ● To pause editing, press START/STOP. Press it again to resume editing. 5 When the time code reaches Edit-Out point (time code from step 1), press START/STOP, then STOP (8) to end Insert Editing. NOTES: ● Program AE with special effects (੬ pg. 47) can be used to spice up the scenes being edited during Insert Editing. ● During Insert Editing, the date and time information changes. ● If you perform Insert Editing onto a blank space on the tape, the audio and video may be disrupted. Make sure you only edit recorded areas. ● During Insert Editing, when the tape moves to scenes recorded in the LP mode or a blank portion, Insert Editing stops. (੬ pg. 59) EDITING EN 55 ADVANCED FEATURES

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
EN
55
EDITING
ADVANCED FEATURES
You can record a new scene into a previously
recorded tape, replacing a section of the original
recording with minimal picture distortion at the in
and out points. The original audio remains
unchanged.
●
Use the provided remote control.
NOTES:
●
Before performing the following steps, make sure
that “TIME CODE” for “CAMERA DISPLAY” and
“VIDEO DISPLAY” is set to “ON”.
(
±
pg. 36, 39, 41)
●
Insert Editing is not possible on a tape recorded in
the LP mode or on a blank portion of a tape.
1
Play back the tape, locate the Edit-Out point
and press
PAUSE
(
9
). Memorize the time code
at this point (
±
pg. 21) since it will be needed to
stop editing in step
5
.
2
Press
REW
(
3
) until the Edit-In point is
located, then press
PAUSE
(
9
).
3
Press and hold
INSERT
(
I
) on the remote
control, then press
PAUSE
(
9
). The “
9
I
”
indicator and the Time Code (min.:sec.) appear
and the camcorder enters Insert-Pause mode.
4
Press
START/STOP
to begin editing.
●
To pause editing, press
START/STOP
. Press it
again to resume editing.
5
When the time code reaches Edit-Out point
(time code from step
1
), press
START/STOP
,
then
STOP
(
8
) to end Insert Editing.
NOTES:
●
Program AE with special effects (
±
pg. 47) can
be used to spice up the scenes being edited
during Insert Editing.
●
During Insert Editing, the date and time
information changes.
●
If you perform Insert Editing onto a blank space on
the tape, the audio and video may be disrupted.
Make sure you only edit recorded areas.
●
During Insert Editing, when the tape moves to
scenes recorded in the LP mode or a blank
portion, Insert Editing stops. (
±
pg. 59)
Insert Editing