JVC DLA-HD10KU DLA-HD10K Owner's Manual (50 pages) - Page 40

What to do when these messages are displayed, Message, Cause Details

Get JVC DLA-HD10KU - 1080p Home Theater Projector PDF manuals and user guides View all JVC DLA-HD10KU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

What to do when these messages are displayed Message No Signal DVI-D Out Of Range Cause (Details) No device is connected to the [DVI] terminal. The DVI-D cable is connected to the [DVI] terminal but there is no signal input. NInput the video signals. A video signal that cannot be used with this unit has been input. NInput 1080/50p or 1080/60p video signals. not available Lamp replacement EXIT Lamp replacement Warning EXIT Upon pressing the [ZOOM T/W] or [FOCUS +/-] button when AZoom/FocusB of the AOptionsB menu is set to ALockB. NSet AZoom/FocusB of the AOptionsB menu to AUnlockB. At the moment when the accumulated lamp time reaches 1900 hours, a ALamp replacementB message will be displayed. In addition, when the accumulated lamp time reaches between 1900 hours to 2000 hours, the (Lamp replacement) message will be displayed each time the projector is turned on. ● The message can be cleared by pressing any button on the remote control or this unit. NGet ready a new lamp (lamp unit) in advance or replace as soon as possible. The ALamp replacementB message will be displayed and the AWarningB word appears blinking when the accumulated lamp time exceeds 2000 hours. The message can be cleared by pressing the [EXIT] button. However, the same message will reappear every hour. When the accumulated lamp time exceeds 2000 hours, the unit cannot be turned on again once it is switched to the standby mode or turned off. If continuous projection is performed after 2000 hours, the unit will shut down upon exceeding 2010 hours and projection will be disabled. NInstall a new lamp (lamp unit) and reset the lamp time. (A Pages 35 - 38) 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
40
What to do when these messages are displayed
Message
Cause (Details)
No device is connected to the [DVI] terminal.
The DVI-D cable is connected to the [DVI] terminal but
there is no signal input.
N
Input the video signals.
A video signal that cannot be used with this unit has
been input.
N
Input 1080/50p or 1080/60p video signals.
Upon pressing the [ZOOM T/W] or [FOCUS +/
-
] button
when
A
Zoom/Focus
B
of the
A
Options
B
menu is set to
A
Lock
B
.
N
Set
A
Zoom/Focus
B
of the
A
Options
B
menu to
A
Unlock
B
.
At the moment when the accumulated lamp time
reaches 1900 hours, a
A
Lamp replacement
B
message
will be displayed.
In addition, when the accumulated lamp time reaches
between 1900 hours to 2000 hours, the (Lamp
replacement) message will be displayed each time the
projector is turned on.
●
The message can be cleared by pressing any button on
the remote control or this unit.
N
Get ready a new lamp (lamp unit) in advance or
replace as soon as possible.
The
A
Lamp replacement
B
message will be displayed
and the
A
Warning
B
word appears blinking when the
accumulated lamp time exceeds 2000 hours.
The message can be cleared by pressing the [EXIT]
button. However, the same message will reappear every
hour.
When the accumulated lamp time exceeds 2000 hours,
the unit cannot be turned on again once it is switched to
the standby mode or turned off.
If continuous projection is performed after 2000 hours,
the unit will shut down upon exceeding 2010 hours and
projection will be disabled.
N
Install a new lamp (lamp unit) and reset the lamp time.
(
A
Pages 35 - 38)
No Signal DVI-D
Out Of Range
not available
Lamp replacement
EXIT
Lamp replacement
EXIT
Warning