JVC GZMC200 Instructions - Page 22

Still Image Recording, Continuous Shooting, Deleting Files

Page 22 highlights

22 EN BASIC OPERATIONS Still Image Recording MODE Power Switch Recording Start/Stop Button Lock Button 1 Set the power switch to while pressing down the lock button located on the switch. 2 Press MODE to select . ● The camera is programmed to record still images on the medium in the CF slot by the factory preset. To switch the recording medium, see pages 26 and 27. ● To change the image size and picture quality, see pages 26 and 29. 3 Press the recording start/stop button. The still image is recorded. ● To check how the image looks before recording, press the recording start/stop button halfway and hold. The indicator appears and stops blinking when the captured image is focused. To cancel the recording, release the recording start/stop button. To record it on the recording medium, press the recording start/stop button fully. NOTES: ● There may be differences in the brightness between the recorded video and still image, even if the same subject is shot. ● To turn the shutter sound off, see page 26. ● For approximate number of storable images, see page 43. Continuous Shooting Keeping the recording start/stop button pressed in step 3 provides an effect similar to serial photography. (Interval between still images: approx. 0.3 seconds) To use this function, set [CONTINUOUS SHOOTING] to [ON]. (੬ pg. 26, 29) ● Continuous shooting may not work well depending on the recording medium. Deleting Files If you press during recording mode, the file recorded most recently will be deleted. ● However, if the recording mode (video, still image or voice) is switched or the power is turned off and on again after recording, you cannot delete the file.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44

22
EN
BASIC OPERATIONS
1
Set the power switch to
while pressing down the
lock button located on the switch.
2
Press
MODE
to select
The camera is programmed to record still images on the
medium in the CF slot by the factory preset. To switch the
recording medium, see pages 26 and 27.
To change the image size and picture quality, see pages 26
and 29.
3
Press the recording start/stop button. The still image is
recorded.
To check how the image looks before recording, press the
recording start/stop button halfway and hold. The
indicator appears and stops blinking when the captured
image is focused. To cancel the recording, release the
recording start/stop button. To record it on the recording
medium, press the recording start/stop button fully.
NOTES:
There may be differences in the brightness between the
recorded video and still image, even if the same subject is
shot.
To turn the shutter sound off, see page 26.
For approximate number of storable images, see page 43.
Continuous Shooting
Keeping the recording start/stop button pressed in step
3
provides an effect similar to serial photography. (Interval
between still images: approx. 0.3 seconds)
To use this function, set [CONTINUOUS SHOOTING] to
[ON]. (
±
pg. 26, 29)
Continuous shooting may not work well depending on
the recording medium.
Deleting Files
If you press
during recording mode, the file recorded
most recently will be deleted.
However, if the recording mode (video, still image or voice) is
switched or the power is turned off and on again after
recording, you cannot delete the file.
Still Image Recording
Power Switch
Lock Button
MODE
Recording Start/Stop Button