Jabra 6293-829-105 Quick Start Guide - Page 2

Basic Opera, Tions

Page 2 highlights

BASIC OPERATIONS Turn headset on/off - Press the multi-function button for 3 to 5 seconds until you see a burst of flashes on the blue indicator light, then release. The indicator lights on the headset and multi-adapter will flash every 3 seconds while the power is on and in "Standby" mode. If you are already wearing the headset, you'll hear a quick series of FOUR tones when turning the headset on or off. When turning on, their pitch will be low to high, and when turning off, their pitch will be high to low. Important: Do not hold the button down too long (more than 3 to 5 seconds) when turning on headset or else the headset may go into pairing mode, and the blue indicator light will turn solid. If that happens, the section below titled "If you press and release and the headset stays in Standby mode" may be applicable to you. Turning multi-adapter on/off - The multi-adapter turns on automatically when you undock the headset, and it turns off when you dock the headset. To turn it off without docking, you can insert the stylus into the stylus switch then press and release the switch. Repeating this will turn it on. Stylus Switch Stylus Multi-adapter Choose wearing preference - FreeSpeak is ready to wear on the right ear. If you prefer the left, gently rotate the MiniGel 180°. Make, answer, and end calls (details on p.12-15 of User Guide) 1. To make or answer calls, press and release ONCE to move the headset from "Standby" to "Active" mode, turning on the audio link between the headset and the multi-adapter. (It may take a few seconds for the audio link to start, so don't press the again.) In Active mode, the indicator lights flash every second. 2. You will then need to dial or answer the call using the phone's keypad. 3. When you're done with the call, use the phone's keypad to end the call. 4. Then press and release again to return to Standby, turning off the audio link. Calls can be made by using voice-activated dialing (available in certain Nextel phone models). Important: Do not hold the only be a quick tap. button down too long when switching modes; this should

  • 1
  • 2
  • 3
  • 4
  • 5

BASIC OPERA
TIONS
Turn headset on/off –
Press the multi-function button
for 3 to 5 seconds until you see a
burst of flashes on the blue indicator light, then release. The indicator lights on the headset and
multi-adapter will flash every 3 seconds while the power is on and in “
Standby
” mode.
If you are already wearing the headset, you’ll hear a quick series of
FOUR
tones when turning the
headset on or off.
When turning on, their pitch will be low to high, and when turning off, their
pitch will be high to low.
Important:
Do not hold the
button down too long (more than 3 to 5 seconds) when
turning on headset or else the headset may go into pairing mode, and the blue indicator light
will turn solid. If that happens, the section below titled
“If you press and release
and
the headset stays in Standby mode
” may be applicable to you.
Choose wearing preference –
FreeSpeak is ready to wear on
the right ear. If you prefer the left, gently rotate the MiniGel 180°.
Make, answer, and end calls
(details on p.12-15 of User Guide)
1.
To make or answer calls, press and release
ONCE
to move the headset
from “
Standby
” to “
Active
” mode, turning on the audio link between the headset
and the multi-adapter. (It may take a few seconds for the audio link to start, so don’t
press the
again.) In
Active
mode, the indicator lights flash every second.
2.
You will then need to dial or answer the call using the phone’s keypad.
3.
When you’re done with the call, use the phone’s keypad to end the call.
4.
Then press and release
again to return to
Standby
, turning off the audio link.
Calls can be made by using voice-activated dialing (available in certain Nextel phone
models).
Important:
Do not hold the
button down too long when switching modes; this should
only be a quick tap.
Multi-adapter
Stylus
Switch
Stylus
Turning multi-adapter on/off -
The multi-adapter turns on auto-
matically when you undock the headset, and it turns off when you
dock the headset. To turn it off without docking, you can insert
the stylus into the stylus switch then press and release the
switch. Repeating this will turn it on.