Kenwood TS-590SG Operation Manual - Page 53

1 Recall the desired memory channel. 2 Press [M.IN] to enter Memory Scroll mode. • To exit Memory Scroll mode, press [CLR]. 3 Select the memory channel where you would like the data copied, using the MULTI/CH control. 4 Press [M.IN]. Channel 00 ~ 99 Channel E0 ~ E9 RX frequency TX frequency Mode for RX Mode for TX Tone frequency CTCSS frequency Tone/ CTCSS ON/ OFF status Memory Name Memory Channel Lockout ON/ OFF Filter A/ B status ➡ Channel 00 ~ 99 Channel E0 ~ E9 ➡ RX frequency ➡ TX frequency ➡ Mode for RX ➡ Mode for TX ➡ Tone frequency ➡ CTCSS frequency ➡ Tone/ CTCSS ON/ OFF status ➡ Memory Name ➡ Memory Channel Lockout OFF ➡ Filter A/ B status Channel 00 ~ 99 Channel E0 ~ E9 ➡ Channel P0 ~ P9 ➡ TX/RX frequency RX frequency ➡ Start frequency ➡ End frequency Mode for RX ➡ Mode for TX/RX TX frequency ➡ -- Mode for TX ➡ -- Tone frequency ➡ Tone frequency CTCSS frequency ➡ CTCSS frequency Tone/ CTCSS/ Cross tone ON/ OFF status ➡ Tone/ CTCSS/ Cross tone ON/ OFF status Memory Name ➡ Memory Name Memory Channel Lockout ON/ OFF ➡ Memory Channel Lockout OFF Filter A/ B status ➡ Filter A/ B status Channel P0 ~ P9 ➡ Channel 00 ~ 99 TX/RX frequency ➡ RX frequency ➡ TX frequency Mode for TX/RX ➡ Mode for RX ➡ Mode for TX Start frequency ➡ -- End frequency ➡ -- Tone frequency ➡ Tone frequency CTCSS frequency ➡ CTCSS frequency Tone/ CTCSS/ Cross tone ON/ OFF status ➡ Tone/ CTCSS/ Cross tone ON/ OFF status MEMORY FEATURES 10 Channel P0 ~ P9 Memory Name Memory Channel Lockout ON/ OFF Filter A/ B status ➡ Channel 00 ~ 99 ➡ Memory Name ➡ Memory Channel Lockout OFF ➡ Filter A/ B status Channel P0 ~ P9 ➡ Channel P0 ~ P9 TX/RX frequency ➡ TX/RX frequency Start frequency ➡ Start frequency End frequency ➡ End frequency Mode for TX/RX ➡ Mode for TX/RX Tone frequency ➡ Tone frequency CTCSS frequency ➡ CTCSS frequency Tone/ CTCSS/ Cross tone ON/ OFF status ➡ Tone/ CTCSS/ Cross tone ON/ OFF status Memory Name ➡ Memory Name Memory Channel Lockout ON/ OFF ➡ Memory Channel Lockout OFF Filter A/ B status ➡ Filter A/ B status Note: After copying, the Memory Channel Lockout turns OFF. STORING FREQUENCY RANGES Memory channels P0 to P9 allow you to store frequency ranges for VFO tuning and Program Scan. Program Scan is described in the next chapter. To tune or scan frequencies within a specified range, store the start and end frequencies for that range in advance. 1 Press [A/B (A=B)] to select VFO A or VFO B. 2 Select the desired start frequency. 3 Press [M.IN] to enter Memory Scroll mode. • To exit Memory Scroll mode and abort the storage process, press [CLR]. 4 Turn the MULTI/CH control, or press Mic [UP]/ [DWN] to select a memory channel in the range of P0 to P9. 5 Press [M.IN] to store the start frequency in the memory channel. • "ENDINPUT" appears on the sub-display. 6 Turn the Tuning control or MULTI/CH control to select the end frequency. 7 Press [M.IN] to store the end frequency in the memory channel. • The previous data stored in the channel is overwritten. 45