Kenwood XD-701 User Manual - Page 60
In case of difficulty
View all Kenwood XD-701 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 60 highlights
60 In case of difficulty XD-SERIES (En) What seems to be a malfunction is not always so. Before calling for service, check the following table according to the symptom of your trouble. Operation to reset The microcomputer may fall into malfunction (impossibility to operate, erroneous display, etc.) when the power cord is unplugged while power is ON or due to an external factor. In this case, execute the following procedure to reset the microcomputer and return it to normal condition. ÷ Please note that resetting the microcomputer clears the contents stored in and returns and to condition when it left the factory. Unplug the power cord from the power outlet then, while holding the eject ENTER key depressed, plug the power cord again. ENTER Preparation section Basic section Remote control unit Symptom Remote control operation is not possible. Cause ÷ Batteries are exhausted. ÷ The remote control is too far away from the system, the controlling angle is deviated or there is an obstacle in between. ÷ There is no tape or CD set in the component to be played. ÷ An attempt is made to play the cassette deck which is recording something. ÷ The MULTI CONTROL setting mode is activated. Remedy ÷ Replace with new batteries. * ÷ Operate the unit inside the remote control- * lable range. ÷ Set a tape or CD in the component to be played. ÷ Wait until the recording ends. ÷ Cancel the MULTI CONTROL setting mode. ( Receiver, speakers Symptom Cause Remedy Sound is not produced. ÷ The speaker cords are disconnected. ÷ The MUTE switch of remote control unit is switched ON. ÷ The headphone plug is inserted into the jack. ÷ Connect properly referring to "System connection". ÷ Switch MUTE OFF. ÷ Unplug the headphone plug. ) AUX (external input) sound is not pro- ÷ The AUX INPUT LEVEL control on the rear ÷ Adjust to an optimum level. duced. panel is set to MIN. o Sub-woofer sound is not produced. ÷ The LEVEL control is set to OFF. ÷ Adjust to an optimum level. ¡ Sound is not output in the TUNER mode. ÷ Sound is not output when the radio wave is ÷ Switch the demonstration off. weak (DEMO ON). 4 The character display blinks and sound is ÷ The speaker cords are short-circuited. not produced. ÷ Turn the power OFF, remove the shortcircuit and turn the power ON again. Sound is not produced from the left or ÷ The speaker cords are disconnected. right speakers. ÷ Connect properly referring to "System connection". The clock display shows ÷ There was a power failure. ÷ The power cord was unplugged from the outlet. ÷ Adjust the present time again. ÷ Adjust the present time again. R R Timer operation is not possible. ÷ The present time has not been adjusted or there was a power failure. ÷ The timer ON time and OFF time have not been set. ÷ The timer execution was not set up. ÷ Adjust the present time referring to "Clock R adjustment". ÷ Set the timer ON time and OFF time. Y ÷ Execute the timer program. I Radio stations cannot be received. ÷ The antennas have not been connected. ÷ A proper broadcasting band has not been selected. ÷ The frequency of the station to be received is not tuned. ÷ Connect antennas. ÷ Select a band. • ÷ Tune to the frequency of the desired station. • Noise interferes. ÷ Car ignition noise. ÷ Influence of an electric appliance. ÷ A TV set is installed near the system. ÷ Install the outdoor antenna in an apart position from the road. ÷ Switch the suspected electric appliance OFF. ÷ Install the TV or the system at an increased distance between them. Application section Knowledge sections