KitchenAid KBNU271VSS Use & Care Guide - Page 20

Conversion from LP Gas to Natural Gas

Get KitchenAid KBNU271VSS PDF manuals and user guides View all KitchenAid KBNU271VSS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Conversion from LP Gas to Natural Gas Installation of the regulator 1. Turn off the main gas supply valve. 2. Unplug grill or disconnect power. 3. Disconnect 20 lb LP gas fuel tank (if present). 4. Turn off all burner control valves. 5. Remove rear cover and 2 screws. 9. Use pipe wrench to install the convertible regulator. Brass cap will be facing up when tight. A B A. Brass elbow B. Convertible regulator 10. To make sure the regulator is set for Natural gas, use adjustable wrench to remove brass cap on appliance regulator. 6. Use adjustable wrench to remove LP hose regulator from brass elbow. Use adjustable wrench to remove brass elbow from shutoff valve. A 11. Examine the stem on the brass cap. If the letters "NAT" are B not showing on the end of the plastic stem farthest away from the brass cap, remove stem from cap, turn it over and snap C stem back into the cap so the letters "NAT" are at the end of the stem farthest away from the brass cap. NAT D A. Manifold B. Brass elbow C. Rear of grill D. Gas pressure regulator/hose assembly 7. Apply pipe sealant to the threads of the brass connector. Use pipe thread sealant that is certified for use with LP gas. 8. Use adjustable wrench to install brass connector (supplied) to shutoff valve. NOTE: The arrow on the regulator must be pointing toward the brass connector. 12. Reinstall cap onto convertible regulator. Change the main grill burner valve orifices 1. Manually remove all of the grates, sear plate, and burners. 2. Remove the 2 screws that hold the burner in place. Remove gas burner from the grill. A A. Two screws 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
20
Conversion from LP Gas to Natural Gas
Installation of the regulator
1.
Turn off the main gas supply valve.
2.
Unplug grill or disconnect power.
3.
Disconnect 20 lb LP gas fuel tank (if present).
4.
Turn off all burner control valves.
5.
Remove rear cover and 2 screws.
6.
Use adjustable wrench to remove LP hose regulator from
brass elbow. Use adjustable wrench to remove brass elbow
from shutoff valve.
7.
Apply pipe sealant to the threads of the brass connector. Use
pipe thread sealant that is certified for use with LP gas.
8.
Use adjustable wrench to install brass connector (supplied) to
shutoff valve.
NOTE:
The arrow on the regulator must be pointing toward
the brass connector.
9.
Use pipe wrench to install the convertible regulator. Brass
cap will be facing up when tight.
10.
To make sure the regulator is set for Natural gas, use
adjustable wrench to remove brass cap on appliance
regulator.
11.
Examine the stem on the brass cap. If the letters “NAT” are
not showing on the end of the plastic stem farthest away from
the brass cap, remove stem from cap, turn it over and snap
stem back into the cap so the letters “NAT” are at the end of
the stem farthest away from the brass cap.
12.
Reinstall cap onto convertible regulator.
Change the main grill burner valve orifices
1.
Manually remove all of the grates, sear plate, and burners.
2.
Remove the 2 screws that hold the burner in place. Remove
gas burner from the grill.
A. Manifold
B. Brass elbow
C. Rear of grill
D. Gas pressure regulator/hose assembly
B
A
C
D
A. Brass elbow
B. Convertible regulator
A. Two screws
A
B
NAT
A