Kodak 5600 User Guide

Kodak 5600 - BC5601 Carousel Projector Manual

Get Kodak 5600 - BC5601 Carousel Projector PDF manuals and user guides
UPC - 041771125677
View all Kodak 5600 manuals
Add to My Manuals
Save this manual to your list of manuals

Kodak 5600 manual content summary:

  • Kodak 5600 | User Guide - Page 1
    Operating Manual KODAK CAROUSEL® Slide Projector CONSUMER IMAGING
  • Kodak 5600 | User Guide - Page 2
    the module to cool before touching the lamp and the surrounding area. Do not place the lamp module on heat-sensitive surfaces. 5. Do not operate your projector if the cord is damaged or if the projector has been dropped or damaged (see "How to Obtain Service" on page 29). 6. Position the cord so
  • Kodak 5600 | User Guide - Page 3
    Operating Manual KODAK CAROUSEL Slide Projector
  • Kodak 5600 | User Guide - Page 4
  • Kodak 5600 | User Guide - Page 5
    Obtain Service 29 Serial Number The serial number of your projector is printed on the label affixed to the power cord retainer on the base of the projector. Record this number, as well as the model identification, date, and place of purchase, for future reference. KODAK CAROUSEL® Slide Projector 1
  • Kodak 5600 | User Guide - Page 6
    a KODAK CAROUSEL Slide Projector which: • triples lamp life • provides brighter and more vivid colors! Introduction Take the time to read the instructions in this operating manual to become familiar with your KODAK CAROUSEL® Slide Projector and how to operate it properly. 2 KODAK CAROUSEL® Slide
  • Kodak 5600 | User Guide - Page 7
    (Model 5600) 12 - Reverse 13 - Forward 14 - Power/Fan/Lamp BACK RIGHT 15 - Tray Release Latch 16 - Lamp Module 17 - Reading Light 18 - Room Light Outlet (Model 5600) 19 - Remote Control Receptacle BASE 20 - Power Cord 21 - Power Cord Retainer 22 - Leveling Foot KODAK CAROUSEL® Slide Projector 3
  • Kodak 5600 | User Guide - Page 8
    compartment and remove the remote control. Plug the 5-pin cable remote connector into the remote-control receptacle, aligning the raised dot with the metallic rivet head. Plug the power cord into a grounded outlet with 110- to 125-volt 60 Hz current only. 4 KODAK CAROUSEL® Slide Projector
  • Kodak 5600 | User Guide - Page 9
    direction of the arrow, and turn the bottom plate until the index hole and notch align. Then release the latch. If you use an 80-slide tray, rotate the metal plate on the bottom of the tray until it locks into position. 140-Slide Tray KODAK CAROUSEL® Slide Projector 80-Slide Tray 5
  • Kodak 5600 | User Guide - Page 10
    of the film's shiny side. Insert your first slide into the first slot in the tray so that the number is visible on the outer circumference of the tray. Insert your second slide in the second slot with the emulsion (dull side) facing your first slide, and so on. 6 KODAK CAROUSEL® Slide Projector
  • Kodak 5600 | User Guide - Page 11
    Operation Replace the lock ring by turning it clockwise until it is secure Tray Place the loaded slide tray on the projector. Align the tray index bar with the gate index. The tray will drop into position. KODAK CAROUSEL® Slide Projector 7
  • Kodak 5600 | User Guide - Page 12
    Operation Removing the Tray To remove the slide tray: • press the select bar all the way down • align the tray index bar with the gate index. You can then lift off the tray. 8 KODAK CAROUSEL® Slide Projector
  • Kodak 5600 | User Guide - Page 13
    Operation Projecting Your Slides Lens To insert a lens, push the focus knob up and position the lens gear teeth on the lens barrel with the notch on the projector. Lamp Slide the power switch to lamp. KODAK CAROUSEL® Slide Projector 9
  • Kodak 5600 | User Guide - Page 14
    changes. The focus button on the cabled remote can be used for Models 4400 and 5600. Random Projection For random projection of any slide in the tray: • press and hold down the select bar, • rotate the tray to the desired slide, and • release the select bar. 10 KODAK CAROUSEL® Slide Projector
  • Kodak 5600 | User Guide - Page 15
    foot at the rear of the projector. Timer (Model 5600 only) To time your slides, use the timer switch for slide changes from 3 to 22 seconds. To interrupt the timer, press either the forward or reverse button. For manual operation, slide the timer switch to Off. KODAK CAROUSEL® Slide Projector 11
  • Kodak 5600 | User Guide - Page 16
    room light into the room light outlet and turn it on. It will remain on until the projector is turned to the lamp position (when a darkened room is required). When you turn the projector off at the end of your presentation, the room light will come on again. 12 KODAK CAROUSEL® Slide Projector
  • Kodak 5600 | User Guide - Page 17
    smaller the f/number), the brighter the projected image. Also, a curved-field lens, in combination with cardboard open face mounts from an automated mounting process, provide superior projection quality. A flat-field lens is the best choice for glass-mounted slides. KODAK CAROUSEL® Slide Projector 13
  • Kodak 5600 | User Guide - Page 18
    have beveled edges around the aperture. Kodak Premium Processing and Kodak Processing labs provide embossed mounts.) Lens Focal Length/ Use the illustration on the following page to help determine the lens focal Projector Distance length and projector distance. 14 KODAK CAROUSEL® Slide Projector
  • Kodak 5600 | User Guide - Page 19
    Operation KODAK CAROUSEL® Slide Projector 15
  • Kodak 5600 | User Guide - Page 20
    the tray to the slide you wish to remove. Firmly press and hold down the select bar to eject the slide. Adding a Slide When the lock ring is off, you can add a slide to any empty slot. (See "Adding Your Slides" on page 6.) Replace and secure the lock ring. 16 KODAK CAROUSEL® Slide Projector
  • Kodak 5600 | User Guide - Page 21
    release latch in the direction of the arrow, and • with your other hand, lift off the back of the tray. KODAK CAROUSEL® Slide Projector With the lock ring firmly in place, turn the 140-slide tray upside down. Retract the tray release latch in the direction of the arrow and align the index hole with
  • Kodak 5600 | User Guide - Page 22
    the lens. Opening the Viewer Grasp the viewer handle and pull it out from the base of the projector. It will pop into place. Slide the power switch to lamp to project your slides. Closing the Viewer To close the viewer, fold it and push it back into the body of the projector. 18 KODAK CAROUSEL
  • Kodak 5600 | User Guide - Page 23
    the lens, push the focus knob up and position the lens gear teeth on the lens barrel with the notch on the projector. Shutdown To shut down, • remove and store the tray • slide the power switch to off Your projector will remain warm for several minutes. KODAK CAROUSEL® Slide Projector 19
  • Kodak 5600 | User Guide - Page 24
    Center at 1-800-242-2424 in the U.S. or 1-800-465-6325 in Canada if you need help identifying your particular model. Lamp Tips • Projector operation on line voltages above 125 volts greatly reduces the lamp life. • Unplug the projector before changing the lamp. 20 KODAK CAROUSEL® Slide Projector
  • Kodak 5600 | User Guide - Page 25
    lamp from the socket and place it on a heat-resistant surface. Insert a new lamp into the socket. Push down to tightly seat the replacement lamp. Relatch the clip in the forward position and push the lamp module all the way back into the projector until it latches. KODAK CAROUSEL® Slide Projector
  • Kodak 5600 | User Guide - Page 26
    projector to cool about 10 minutes. Push the lamp-module release button and remove the lamp module. Use a torx-head screwdriver to remove the screw. Using a flat-blade screwdriver, apply ample pressure to release each of the metal tabs. Lift off the top of the lamp module. 22 KODAK CAROUSEL® Slide
  • Kodak 5600 | User Guide - Page 27
    pulling it out. Wear gloves to prevent fingerprints. Heat-Absorbing Glass Caution The heat-absorbing glass is fragile. Handle it only when cool. (For lamp modules The green-tinted heat-absorbing glass easily removes for cleaning. with a heat-absorbing glass.) KODAK CAROUSEL® Slide Projector 23
  • Kodak 5600 | User Guide - Page 28
    insert each tab into its appropriate slot. Start with the tabs in the rear of the lamp module. Insert the remainder of the tabs into slots until all 7 tabs on the top and 2 on the bottom are secured. Insert the screw and tighten. Then insert and seat the lamp. 24 KODAK CAROUSEL® Slide Projector
  • Kodak 5600 | User Guide - Page 29
    Mirror Maintenance To clean the mirror, invert the lamp module to reach the mirror. Gently clean the mirror with a soft, lint-free cloth moistened with lens cleaner. When your maintenance is complete, push the lamp module back into the projector. KODAK CAROUSEL® Slide Projector 25
  • Kodak 5600 | User Guide - Page 30
    Troubleshooting Consult this guide before calling for service. PROBLEM CAUSE CORRECTION Projector does not operate No power to projector Plug power cord into suitable electrical outlet. Set power switch to Lamp. No illumination on screen with slide in Power switch on Off or Fan projector
  • Kodak 5600 | User Guide - Page 31
    notch. Reposition tray on projector. Straighten mount or remount slide. Set projector on a stand equal with center of screen. Check lamp. Check condenser lens. Check slide position and slidemount condition. Reposition tray. See "Clearing a Gate Jam" on page 17. 27 KODAK CAROUSEL® Slide Projector
  • Kodak 5600 | User Guide - Page 32
    warranty does not cover circumstances beyond Kodak's control, projector lamps, or problems caused by failure to follow the care and operating instructions in the manual. Any modification to the original design of this projector nullifies this warranty. Warranty service will not be provided without
  • Kodak 5600 | User Guide - Page 33
    Obtain Service Assistance Shipping Instructions To obtain service or for assistance in using your KODAK CAROUSEL Slide Projector, contact the Kodak Kodak in your country. To help us get your KODAK CAROUSEL Slide Projector back to you promptly, please enclose a note giving details of the problem
  • Kodak 5600 | User Guide - Page 34
    Consumer Imaging EASTMAN KODAK COMPANY Rochester, New York 14650 www.kodak.com/go/projectors Kodak, Ektagraphic, and Kodalux are trademarks. CONSUMER IMAGING Part No. 5B4904 1/03 Minor Revision ©EastmanKodak Company Printed In U.S.A.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
Operating Manual
CONSUMER IMAGING
KODAK
CAROUSEL
®
Slide Projector