Konica Minolta Kodak i1440 User Guide - Page 38

Cleaning the imaging guides, Running a transport cleaning sheet, Cleaning the, imaging guides

Get Konica Minolta Kodak i1440 PDF manuals and user guides View all Konica Minolta Kodak i1440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Cleaning the imaging guides Clean the exposed (top side) surfaces of the imaging guides. You do not need to remove the imaging guides for cleaning unless there is dust or dirt on the underside of the imaging guide. If you need to remove the imaging guides, follow the instructions for "Replacing the imaging guides" later in this chapter. 1. Wipe the upper and lower imaging guides with a Staticide Wipe. 2. Dry the imaging guides with an almost dry Staticide Wipe. 3. Close the scanner cover with both hands; push it down firmly until it latches into place. Running a transport cleaning sheet 1. Remove the wrapping from the Transport Cleaning Sheet. 2. Adjust the side guides to fit the cleaning sheet. 3. Feed the cleaning sheet (adhesive side up) through the scanner in portrait orientation until all residue is removed from the drive rollers. 4. Adjust the side guides to fit, then feed the cleaning sheet (adhesive side up) through the scanner in landscape orientation until all residue is removed from the drive rollers. 5. Using the same cleaning sheet, repeat Steps 3 and 4, but feed the cleaning sheet through the scanner with the adhesive side down until all residue is removed from the drive rollers. NOTE: When a cleaning sheet gets very dirty, discard it and use a new one. A-61550 February 2010 5-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
A-61550
February 2010
5-7
Cleaning the
imaging guides
Clean the exposed (top side) surfaces of the imaging guides. You do
not need to remove the imaging guides for cleaning unless there is dust
or dirt on the underside of the imaging guide. If you need to remove the
imaging guides, follow the instructions for “Replacing the imaging
guides” later in this chapter.
1.
Wipe the upper and lower imaging guides with a Staticide Wipe.
2.
Dry the imaging guides with an almost dry Staticide Wipe.
3.
Close the scanner cover with both hands; push it down firmly until it
latches into place.
Running a transport
cleaning sheet
1.
Remove the wrapping from the Transport Cleaning Sheet.
2.
Adjust the side guides to fit the cleaning sheet.
3.
Feed the cleaning sheet (adhesive side up) through the scanner in
portrait orientation until all residue is removed from the drive rollers.
4.
Adjust the side guides to fit, then feed the cleaning sheet (adhesive
side up) through the scanner in landscape orientation until all
residue is removed from the drive rollers.
5.
Using the same cleaning sheet, repeat Steps 3 and 4, but feed the
cleaning sheet through the scanner with the adhesive side down
until all residue is removed from the drive rollers.
NOTE: When a cleaning sheet gets very dirty, discard it and use a
new one.