Konica Minolta bizhub PRESS 1250 SDD 2-Side Trimmer/Square Fold Unit User Guid - Page 14

Job Setup, Job name'.

Get Konica Minolta bizhub PRESS 1250 PDF manuals and user guides View all Konica Minolta bizhub PRESS 1250 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Operator Manual STR0202 & SFM0704 DBCB-0512-0066-V005 STR0202 2-Side Trimmer & SFM0704 Square Fold Module 4. Operating the STR (continued) 4.5 Job Setup Fig. 1 Fig. 2 Fig. 3 Step Action 1. Job Setup 2A. Make a new Job 2A. Enter Job name 2B. Adjust a Job 3. Adjust Input Size and/or Side Trim 4. Save Job V005 RI01 23-04-2012 Fig. 4 Remarks Press the 'Jobs' button two times (Fig. 1& 2). Press the 'New' button (Fig. 3). Use the '+ / -' and '►' buttons (Fig. 4) to Enter the Job name and press the 'Enter' button. A "Loading Job" message appears for a few seconds. Use the buttons to select a Job and press the 'Enter' button to load or confirm. A "Loading Job" message appears fora few seconds. Use the and the '+ / -' buttons to set the desired settings for Input Size and Side Trim (See Chapter: 4.6 Paper Input Size Setup 4.7 Side Trim ON/OFF) After adjusting press 'Jobs' (Fig. 1) and save the current Job or 'Rename' the adjusted Job by pressing the 'Enter' button (Fig. 2). A "Saving Job" message appears for a few seconds. After Renaming a Job, repeat step 2A: 'Enter Job name'. DBCB-0512-0066-V005 - 14 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
Operator Manual STR0202 & SFM0704
DBCB-0512-0066-V005
STR0202 2-Side Trimmer & SFM0704 Square Fold Module
V005
RI01
23-04-2012
DBCB-0512-0066-V005
- 14 -
4. Operating the STR
(continued)
4.5 Job Setup
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Step
Action
Remarks
1.
Job Setup
Press the ‘Jobs’ button two times (Fig. 1& 2).
2A.
Make a new Job
Press the ‘New’ button (Fig. 3).
2A.
Enter Job name
Use the ‘
+
/
-
‘ and ‘
►’
buttons (Fig. 4) to Enter the Job
name and press the ‘Enter’ button.
A “Loading Job” message appears for a few
seconds.
2B.
Adjust a Job
Use the ‘
▲ /
▼ ’
buttons to select a Job and press the
‘Enter’ button to load or confirm.
A “Loading Job” message appears fora few
seconds.
3.
Adjust Input Size and/or Side
Trim
Use the ‘
▲ /
▼ ’
and the
‘
+
/
-
‘ buttons to set the
desired settings for Input Size and Side Trim
(See Chapter:
4.6
Paper Input Size Setup
4.7 Side Trim ON/OFF
)
4.
Save Job
After adjusting press ‘Jobs’ (Fig. 1) and save the current
Job or ‘Rename’ the adjusted Job by pressing the
‘Enter’ button (Fig. 2).
A “Saving Job” message appears for a few
seconds.
After Renaming a Job, repeat step 2A: ‘Enter
Job name’.