Kyocera 9530DN Operation Guide

Kyocera 9530DN - B/W Laser Printer Manual

Get Kyocera 9530DN - B/W Laser Printer PDF manuals and user guides View all Kyocera 9530DN manuals
Add to My Manuals
Save this manual to your list of manuals

Kyocera 9530DN manual content summary:

  • Kyocera 9530DN | Operation Guide - Page 1
    FS-9130DN FS-9530DN Advanced Operation Guide
  • Kyocera 9530DN | Operation Guide - Page 2
  • Kyocera 9530DN | Operation Guide - Page 3
    Making Default Settings ...2-42 Pagination ...2-51 Setting Print Quality ...2-58 Operating the Storage Device 2-62 Paper Handling ...2-73 Reading Life Counters ...2-86 Other ...5-6 RS-232C Protocol ...5-7 RS-232C Cable Connection ...5-10 Glossary...1 Index...1 ADVANCED OPERATION GUIDE i
  • Kyocera 9530DN | Operation Guide - Page 4
    Contents ii ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 5
    Introduction This guide has the following chapters: • 1 Handling Paper Explains how to choose, handle and load paper. • 2 Using the Operation Panel Explains how to use the operation panel to configure the printer. • 3 Fonts Shows the available fonts. • 4 Options Shows the available options. • 5
  • Kyocera 9530DN | Operation Guide - Page 6
    names displayed on the operation panel. Replace the waste toner box when the Check waste toner box message is displayed. Used to denote refer to step 10. Used to provide important information. IMPORTANT: Ensure paper is not folded, curled, or damaged. Cautions are statements that suggest
  • Kyocera 9530DN | Operation Guide - Page 7
    1 Handling Paper This chapter explains the following topics: • General Guidelines 1-2 • Special Paper 1-9 • Media Type 1-13 • Loading Paper 1-14 ADVANCED OPERATION GUIDE 1-1
  • Kyocera 9530DN | Operation Guide - Page 8
    no liability for problems that occur when paper not satisfying these requirements is used. Selection of the right paper is important. Using the wrong paper can result in paper jams, misfeeding, curling, poor print quality, and paper waste, and in extreme cases can damage the printer. The guidelines
  • Kyocera 9530DN | Operation Guide - Page 9
    Handling Paper Paper Specifications The following table summarizes the basic paper specifications. Details are given on the following pages. Weight Item Thickness Dimensional accuracy Squareness of corners Moisture content Direction of grain Pulp content Specification Cassette: 60 to 105 g/m2 (
  • Kyocera 9530DN | Operation Guide - Page 10
    Paper Selecting the Right Paper Laser printing is a process involving laser light, electrostatic discharge, toner, and heat. In addition, as the paper passes through the printer it undergoes considerable sliding, bending, and twisting motions. A highquality printing paper matching the printer
  • Kyocera 9530DN | Operation Guide - Page 11
    is too light or too heavy can cause misfeeding, jams, and premature wear of the printer. Uneven paper weight can cause multiple feeds, print defects, poor toner fusing, blurring, and other print quality problems. The proper weight is 60 to 105 g/m2 for the paper cassette, and 45 to 200 g/m2 for the
  • Kyocera 9530DN | Operation Guide - Page 12
    lowcaliper paper. The paper used with the printer should be neither extremely thick nor extremely thin. If you are having problems with paper jams, multiple feeds, and faint printing, the paper you are using may be too thin. If you are having problems with paper jams and blurred printing, the paper
  • Kyocera 9530DN | Operation Guide - Page 13
    jam. Curl: Most paper has a natural tendency to curl in one direction. The paper should be loaded so that the natural curl is downward, to counteract the upward curl imparted by the printer. Printed sheets will then come out flat. Most paper also has a top and bottom surface. Loading instructions
  • Kyocera 9530DN | Operation Guide - Page 14
    edges, welded (uncut) sheets, and crushed edges and corners can cause the printer to malfunction in various ways. A quality paper supplier should take considerable care to ensure that these problems do not occur. Packaging: Paper should be packed in a sturdy carton to protect it from damage during
  • Kyocera 9530DN | Operation Guide - Page 15
    give trouble during printing. No liability will be assumed if moisture, etc., given off in printing on special paper causes harm to the machine or operator. NOTE: Before purchasing any type of special paper, test a sample on the printer and check that print quality is satisfactory. Specifications
  • Kyocera 9530DN | Operation Guide - Page 16
    to give trouble in printing. Top sheet (White bond paper) Adhesive Carrier sheet Adhesive label paper must be entirely covered by its top sheet, with no spaces between the individual labels. Labels with spaces in between are apt to peel off, causing serious paper jam problems. 1-10 ADVANCED
  • Kyocera 9530DN | Operation Guide - Page 17
    postcards may cause paper jams. Some postcards have rough edges on the back (those are created when the paper is cut). In this case, put the postcards on a flat place and rub the edges with, for example, a ruler to smooth them. Envelopes The printer can print on envelopes using paper with a basis
  • Kyocera 9530DN | Operation Guide - Page 18
    Paper Select recycled paper that meets the same specifications as the white bond paper (refer to Paper Specifications on page 1-3) except whiteness. NOTE: Before purchasing recycled paper, test a sample on the printer and check that the print quality is satisfactory. 1-12 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 19
    paper being used. Setting the paper type for the paper source from the printer's operation panel will cause the printer to automatically select the paper source and print in the mode best suited to that type of paper. A different paper Cannot be used Paper Weight Normal 2 paper type defined and
  • Kyocera 9530DN | Operation Guide - Page 20
    it on a level surface. This avoid media jams or skewed printing. Loading Paper into the Paper Cassette Up to about 500 sheets of standard paper (80 g/m2) can be loaded into the each paper cassette. Inch specifications Each paper cassette can be set to hold paper of any desired size from 11 × 17 to
  • Kyocera 9530DN | Operation Guide - Page 21
    Handling Paper 2 Hold the paper guide and move it to align the paper guide with the required paper width. Paper sizes are marked inside the paper cassette. ADVANCED OPERATION GUIDE 1-15
  • Kyocera 9530DN | Operation Guide - Page 22
    paper into the paper cassette, make sure that the print side is facing upward. (The print side is the side facing upward when the package is opened.) Check that the paper guide makes secure contact with the paper. If there is a gap, adjust the position of the paper guide. If small-size paper jams
  • Kyocera 9530DN | Operation Guide - Page 23
    loaded can be checked by looking at the front of the paper cassette. 6 Push the paper cassette back until it stops. NOTE: Before leaving the printer in disuse for a prolonged period of time, remove the paper from the paper cassette(s) and seal it in its original packaging to protect from moisture
  • Kyocera 9530DN | Operation Guide - Page 24
    1-13. NOTE: The number of sheets of standard paper that can be loaded in the MP tray at a time is approximately 200. When using transparencies, load a single sheet at a time. 1 Fan the paper, then tap it on a level surface to avoid media jams or skewed printing. 2 Open the MP tray. 1-18 ADVANCED
  • Kyocera 9530DN | Operation Guide - Page 25
    3 Adjust the insert guides to the size of the paper to be loaded. 4 Insert the paper along the guides as far as it will go. IMPORTANT: When loading paper into the MP tray, make sure that the print side is facing upward. (The print side is the side facing upward when the package is opened.) If the
  • Kyocera 9530DN | Operation Guide - Page 26
    Handling Paper Setting Envelopes When using the optional printer function, envelopes can be set in the MP tray. NOTE: Do not print on envelopes with flap adhesive exposed. This can cause printer malfunction. 1 Open the MP tray. 2 Align the insert guides with the envelope size. 3 Position the
  • Kyocera 9530DN | Operation Guide - Page 27
    limits on the inside of the MP tray. If the paper is considerably curled in one direction, for example, if the paper is already printed on one side, try to roll the paper in the opposite direction to counteract the curl. Printed sheets will then come out flat. Correct Incorrect ADVANCED OPERATION
  • Kyocera 9530DN | Operation Guide - Page 28
    Handling Paper 1-22 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 29
    the following topics: • Understanding the Operation Panel 2-2 • Canceling a Printing Job 2-10 • Using the Operation Panel 2-11 • Using the Menu Settings 2-42 • Pagination 2-51 • Setting Print Quality 2-58 • Operating the Storage Device 2-62 • Paper Handling 2-73 • Reading Life Counters 2-86
  • Kyocera 9530DN | Operation Guide - Page 30
    , and eight keys. Message Display (Refer to page 2-4) Operation Indicators (Refer to page 2-3) Ready --- A4 PLAIN Paper Type Indicator (Refer to page 2-7) Paper Size Indicator (Refer to page 2-5) Interface Indicator (Refer to page 2-5) Keys (Refer to page 2-8) 2-2 ADVANCED OPERATION
  • Kyocera 9530DN | Operation Guide - Page 31
    when the printer needs maintenance attention or the printer is warming up (Please wait). Lit: Indicates when a problem or an error occurs that you can clear by yourself. (For example, paper jam occurs.) 1 Flashing: Indicates when no paper is detected. Fast-Flashing: Indicates that a paper jam is
  • Kyocera 9530DN | Operation Guide - Page 32
    and is not ready. When the printer is switched on for the first time after the toner container is installed, (Adding toner) also appears. The printer is ready to print. The printer is receiving data, generating graphics, reading a memory card/hard disk, or printing. The printer is in Sleep mode. The
  • Kyocera 9530DN | Operation Guide - Page 33
    the interface, you should wait for this period until the other interface begins printing the job. Paper Size Indicator This indicator shows the paper size of the current paper cassette. The following abbreviations are used to indicate the paper sizes. Message Display A3 A4 A5 A6 B5 B6 LT LG MO 10
  • Kyocera 9530DN | Operation Guide - Page 34
    DL C5 b5 EX #6 #9 HA OH CU C4 O2 ST Y2 8K 16K Paper Size Folio Youkei 4* Envelope DL* Envelope C5* ISO B5* Executive* Envelope #6* the MP tray feeding NOTE: While the printer is processing data, the SIZE display indicates the paper size selected by the application software. 2-6 ADVANCED
  • Kyocera 9530DN | Operation Guide - Page 35
    media type can be specified at the operation panel. Refer to Creating Custom Paper Type on page 2-82. The following abbreviations are used to indicate the Vellum* Recycled Rough Letterhead Color Prepunched Envelope* Cardstock* Thick paper* High quality paper Custom 1 (to 8) * With only the MP tray
  • Kyocera 9530DN | Operation Guide - Page 36
    and off-line. Use this key to: • Toggle the printer's on-line and off-line states. You can temporarily stop the print job by switching the printer off-line. • Print and feed out one page when the printer displays Waiting. • Recover from certain errors. • Recover from Auto Sleep. CANCEL Key This key
  • Kyocera 9530DN | Operation Guide - Page 37
    may be pressed when the paper jam message has appeared on the message display. A help message will then appear to facilitate jam clearing in the location. paper source when Use alternative? is shown in the message display. * If you hold down [OK] and press [MENU] when Ready is shown on this printer
  • Kyocera 9530DN | Operation Guide - Page 38
    Using the Operation Panel Canceling a Printing Job 1 While the printer displays Processing, press [CANCEL]. Print Cancel? appears on the message display followed [OK]. Canceling data appears on the message display and printing stops after the current page is printed. 2-10 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 39
    the number of copies to print, emulation, etc., to your specific needs. Settings can be made when Ready is indicated on the printer message display. The printer obeys the most recently received printer settings sent from the application software, or from the printer driver, which take priority over
  • Kyocera 9530DN | Operation Guide - Page 40
    2 >Parity None >Protocol DTR(pos.)&XON >>Frame Type Auto >>DHCP Off >>DHCP On >>BOOTP Off >>BOOTP On >>IP Address >>Subnet Mask >>Gateway 2-12 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 41
    Printer Emulation IBM Proprinter Emulation DIABLO 630 Emulation EPSON LQ-850 Emulation PCL 6 Emulation KC-GL Font > >Print KPDL Errs On >Print KPDL Errs Off >Print KPDL Errs On >Print Continued on the next page >Code Set IBM PC-8 >Print Internal Fonts List >Print Option Fonts List Using the
  • Kyocera 9530DN | Operation Guide - Page 42
    Using the Operation Panel Continued Page Set > Print Quality > Hard Disk > Continued on the next page >Copies 001 >Zoom >Orientation Portrait KIR Mode Off >EcoPrint Mode Off >EcoPrint Mode On >Resolution Fast 1200 mode >Print Density 04 >Read Data >Write Data >Delete Data >Delete Font >Format
  • Kyocera 9530DN | Operation Guide - Page 43
    Memory > Continued on the next page >RAM Disk Size >Read Data >Write Data >Delete Data >Delete Font >Print Partition List >Read Fonts >Read Data >Write Data >Delete Data >Format >Print Partition List >Read Data >Remove Device >Print Partition List Using the Operation Panel ADVANCED OPERATION
  • Kyocera 9530DN | Operation Guide - Page 44
    Using the Operation Panel Continued Paper Handling > Continued on the next page >MP Tray Mode Cassette >MP Tray Mode First >MP Tray Size A4 >MP Tray Type >Reset Type Adjust >>Unit mm >>Unit inch >>Paper Weight Normal 1 >>Duplex Path Enable >>Duplex Path Disable 2-16 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 45
    Pages 0000001 >Encryption Code >Overwrite Mode >Secure Format >MSG Language English >Form Feed Time Out 000sec. >Sleep timer > 015 min. >Print HEX-DUMP >Restart Printer >Resource Prot. Off >Buzzer > >Auto Error Clear Off >Auto Error > Clear On >Finishing > Error Continued on the next page
  • Kyocera 9530DN | Operation Guide - Page 46
    Using the Operation Panel Continued >Service > >>Print Status Page >>Print Event Log >>Paper Feed Normal >>Paper Feed > Special >>Developer >>Charger >>Drum 2-18 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 47
    on the printer. 1 Press [MENU]. 2 Press U or V repeatedly until Print Menu Map appears. Print Menu Map 3 Press [OK]. A blinking question mark (?) appears. Print Menu Map ? 4 Press [OK] again. The printer prints a menu map. FS-9530DN Page Printer MENU MAP ADVANCED OPERATION GUIDE 2-19
  • Kyocera 9530DN | Operation Guide - Page 48
    page is a list of parameters and settings for most basic printer configurations. You may be required to produce a status page when requesting service to the printer. Printing Status Page If you want to check the printer's current status, including memory available and option settings, you can
  • Kyocera 9530DN | Operation Guide - Page 49
    to the contents explained on the next page. Hardware Information 2 FS-9530DN Page Printer STATUS PAGE Firmware Version: Released: 1 Memory 3 Page Information 4 Network Status 6 Interfaces Installed Options Emulation Error Log Toner Gauge 0 5 7 8 9 100 10 KIR Test pattern ON 11 When
  • Kyocera 9530DN | Operation Guide - Page 50
    to Maintenance Messages on page 4-7 in the Operation Guide. Error information is cleared when the printer's power is turned off. 9 Toner Gauge This shows the approximate level of remaining toner. When the value is 100, the toner container is full. NOTE: If you are not using an original Kyocera toner
  • Kyocera 9530DN | Operation Guide - Page 51
    available from the printer driver: • Job Retention • Job Storage In either job mode, when printing a document, the print data is transferred from the computer to the printer then stored on the printer's hard disk. Since copies of the document are printed using the stored data, printing is performed
  • Kyocera 9530DN | Operation Guide - Page 52
    printing Data when power off Private Print Stored Job To hold the document in printer to prevent unauthorized access To electronically store documents such as fax cover pages Printer driver Printer driver on the printer driver when printing. To retrieve the stored job for printing, refer to
  • Kyocera 9530DN | Operation Guide - Page 53
    in this example). The user name Harold is assigned at printing using the printer driver. 5 Press [OK]. A blinking question mark (?) appears be printed can be set. To increase the copy >Report count, press U; to decrease the copy count, Copies press V. 001 ADVANCED OPERATION GUIDE 2-25
  • Kyocera 9530DN | Operation Guide - Page 54
    access codes are not mandatory, but can be set on the printer driver if printing with the PIN security is required. Then, the access code must be entered on the operation panel to print a stored job. Print data will be stored in the hard disk/RAM disk after printing. 2-26 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 55
    entered in >Arlen the printer driver appear with a blinking four-digit access code entered in >Agenda the printer driver and press [OK printed. To increase the copy count, press U; to decrease the copy count, press V. >Agenda Copies 001 11 Press [OK] to finalize the copy count. The printer prints
  • Kyocera 9530DN | Operation Guide - Page 56
    on the Software Library CDROM. For details, refer to the KM-NET for Clients Operation Guide. Printing a List of Code Jobs If you select Permanent Job Storage on the printer driver, you can have a List of Code Jobs printed using the operation panel. 1 Press [MENU]. 2 Press U or V repeatedly until
  • Kyocera 9530DN | Operation Guide - Page 57
    Using the Operation Panel 6 Press [OK] again. Processing appears and printer prints a Code Job list as shown below. FS-9530DN Page Printer PERMANENT CODE JOB LIST Retrieving Jobs from Virtual Mailbox (VMB) To retrieve the jobs posted in the virtual mailbox, proceed as follows. 1 Press [MENU]. 2
  • Kyocera 9530DN | Operation Guide - Page 58
    VMB List appears. >Print VMB List 5 Press [OK]. A blinking question mark (?) appears. >Print VMB List ? 6 Press [OK] again. The printer prints a list of jobs currently posted in the virtual mailboxes as shown below. FS-9530DN Page Printer VIRTUAL MAIL BOX LIST 2-30 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 59
    code jobs • Maximum space assigned to virtual mailboxes NOTE: The total amount of storage area specified must not exceed the total size of the hard disk. Otherwise, you may only be able to accommodate a smaller number of print [MENU]. The display returns to Ready. ADVANCED OPERATION GUIDE 2-31
  • Kyocera 9530DN | Operation Guide - Page 60
    Temporary Code Jobs This changes the hard disk space that holds temporary code jobs. Press U or V repeatedly until >>Temp. Code JOB Size appears. >>Temp. Code JOB Size 0500MB 7 To change the maximum disk [OK]. A blinking cursor (_) appears. >>Temp. Code JOB Size 0500MB 8 Press U or V to
  • Kyocera 9530DN | Operation Guide - Page 61
    . Code JOB Size 0500MB 8 Press U or V to increase or decrease, respectively, the value at the blinking cursor. Use Z and Y to move the cursor right and left. 9 When the desired size is displayed, press [OK]. 10 Press [MENU] and the message display returns to Ready. ADVANCED OPERATION GUIDE 2-33
  • Kyocera 9530DN | Operation Guide - Page 62
    move the cursor right and left. 9 When the desired size is displayed, press [OK]. 10 Press [MENU] to exit the menu selection. 2-34 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 63
    printing environment parameters such as the default emulation can be changed independently on different interfaces by using the printer printer automatically selects an interface. Changing Parallel Interface Modes The parallel interface supports >Parallel I/F ?Auto ADVANCED OPERATION GUIDE 2-35
  • Kyocera 9530DN | Operation Guide - Page 64
    interface, refer to the IB-11 Installation Guide. After setting the interface, be sure to reset the printer or turn the power off at least once the serial interface. NOTE: This section applies to the printer having the optional RS-232C interface card kit (IB-11) installed. 1 Press [MENU]. 2 Press
  • Kyocera 9530DN | Operation Guide - Page 65
    The message display returns to Ready. Changing Network Interface Parameters This printer supports TCP/IP, NetWare and AppleTalk protocols. In addition, you can default gateway address • Determine whether to print a network status page when the printer is turned on ADVANCED OPERATION GUIDE 2-37
  • Kyocera 9530DN | Operation Guide - Page 66
    NetWare Off >TCP/IP Off >AppleTalk Off If On, print the standard Network Interface Status Page after the Printer Status Page. Refer to page 2-20. >Network Status Page Off If On, print the optional Network Interface Status Page after the Printer Status Page. Refer to page 2-20. >Opt. StatusPage
  • Kyocera 9530DN | Operation Guide - Page 67
    Panel 7 The following example explains how to activate TCP/IP protocol to connect the >TCP/IP > printer in the network. You can select On Netware or AppleTalk in a similar manner. If TCP/IP left. 11 To obtain these addresses, consult your network administrator. ADVANCED OPERATION GUIDE 2-39
  • Kyocera 9530DN | Operation Guide - Page 68
    firmware version, the network addresses, and other information under various network protocols about the network interface. The default setting is On (print). The network interface status page will be printed out after the printer status page. NOTE: Printing ? Off 2-40 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 69
    Using the Operation Panel 9 Press [OK] again. >Network Status Page Off 10 Press [MENU]. The message display returns to Ready. FS-9530DN Page Printer NETWORK STATUS PAGE ADVANCED OPERATION GUIDE 2-41
  • Kyocera 9530DN | Operation Guide - Page 70
    the Kyocera's implementation of the PostScript language. The KPDL (AUTO) emulation enables the printer to automatically change the emulation mode according to the data received when printing. In 6 3 Press [OK]. A blinking question mark (?) appears. Emulation ?PCL 6 2-42 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 71
    . Auto Printing of KPDL Error The printer can be set to print error data during KPDL emulation. If this is set to On, error data will be printed only when trouble occurs during printing. The 4 Select KPDL or KPDL (AUTO) using U or V. Emulation ?KPDL 5 Press [OK]. ADVANCED OPERATION GUIDE 2-43
  • Kyocera 9530DN | Operation Guide - Page 72
    or V to change it. 7 Press [OK]. A blinking question mark (?) appears. >Print KPDL Errs ?Off 8 Select On using U or V. >Print KPDL Errs ?On 9 Press [OK]. 10 Press [MENU]. The message display returns to GL > Pen Width 7 Press Z. >>Pen(1) Width 01 dot(s) 2-44 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 73
    B1, B0, and SPSZ) appears. When selecting SPSZ, printing will be done with the paper size specified by the PRESCRIBE SPSZ command. 13 Press [OK to the internal fonts, all fonts that are downloaded to the printer memory, or fonts stored on a memory card, printer. ADVANCED OPERATION GUIDE 2-45
  • Kyocera 9530DN | Operation Guide - Page 74
    indicates the type of font as follows: >> I000 Letter I S M H Description Internal fonts Soft (download) fonts Fonts in an option memory card Fonts in a RAM disk or hard disk 5 Press [OK 6 Press U or V repeatedly until >>Courier appears. >>Courier Regular 2-46 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 75
    move the cursor right and left. 9 When the desired size is displayed, press [OK]. 10 Press [MENU]. The message display returns to Ready. ADVANCED OPERATION GUIDE 2-47
  • Kyocera 9530DN | Operation Guide - Page 76
    [OK]. 10 Press [MENU]. The message display returns to Ready. Setting the character code set You can change the character code set. Available character code sets vary depending on the current font. (The default character code set is IBM PC8.) 1 Press [MENU]. 2 Press U or V repeatedly until Font
  • Kyocera 9530DN | Operation Guide - Page 77
    Set ?IBM PC-8 6 Press U or V until the desired character code set appears. 7 Press [OK]. 8 Press [MENU]. The display returns to Ready. Printing a List of Fonts To help in selecting fonts, you can print a list of the fonts including option fonts. 1 Press [MENU]. 2 Press U or V repeatedly until
  • Kyocera 9530DN | Operation Guide - Page 78
    Using the Operation Panel 6 Press [OK] again. Processing appears, then Ready. The printer prints a list of fonts with a short sample and font ID (number) for each font. Internal Fonts List PRESCRIBE Font Name Scalable/Bitmap Password Selection [FSET] Font ID 2-50 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 79
    Copies You can set the number of copies of each page to be printed for the current interface. The number of copies can be set between 1 the source paper size and the paper size to use after reduction. NOTE: Printed results when making reductions differ from equivalent size printing. Sometimes the
  • Kyocera 9530DN | Operation Guide - Page 80
    the same as the paper size set for print data from the computer. Target size indicator...This is the paper size after reduction. This must be the same as the paper size set for the paper cassette. The message ] [B5]98% [A4] [LT] [B5] [A5] [A4]98% [B4] [B5] [A4] [B4]98% 2-52 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 81
    appears. >Zoom [CS]→[CS] 5 Press [OK]. A blinking cursor (_) appears under the paper size. >Zoom [CS]→[CS] 6 Press U or V to select source size. Both the cursor to the target size. >Zoom [B4]→[B4] 8 To make a reduced print, press U or V to select the target size. >Zoom [B4]→[A4] 9 Press
  • Kyocera 9530DN | Operation Guide - Page 82
    menu does not usually appear, Page Protect will be forcibly set to On if a Print overrun Press GO error occurs due to insufficient printer memory. Be sure to return this setting to Auto in order to maintain high printer memory efficiency. This can be done as follows. 1 Press [MENU]. 2 Press U or
  • Kyocera 9530DN | Operation Guide - Page 83
    The message display returns to Ready. Linefeed (LF) Action This procedure instructs the printer what to do when it receives a linefeed code (character code 0AH). 1 Press [MENU]. 2 Press U or V repeatedly until Press [MENU]. The message display returns to Ready. ADVANCED OPERATION GUIDE 2-55
  • Kyocera 9530DN | Operation Guide - Page 84
    CR) Action This procedure instructs the printer what to do when it receives a carriagereturn code (character code 0DH). 1 Press [MENU this On to increase the maximum number of characters that can be printed in a line for A4 page (78 characters at 10 pitch >Wide A4 Off 2-56 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 85
    Using the Operation Panel 5 Press [OK]. A blinking question mark (?) appears. >Wide A4 ? Off 6 Select On or Off using U or V. 7 Press [OK]. 8 Press [MENU]. The message display returns to Ready. ADVANCED OPERATION GUIDE 2-57
  • Kyocera 9530DN | Operation Guide - Page 86
    KIR mode setting. Status Page KIR Test Pattern Hardware Information FS-9530DN Page Printer STATUS PAGE Firmware Version: Released: Memory Page Information Network Status Interfaces Installed Options Emulation Error Log Toner Gauge 0 100 KIR Test pattern ON Optimized stripes The
  • Kyocera 9530DN | Operation Guide - Page 87
    reduce the amount of toner consumed on the page so as to save your printing costs. You can set EcoPrint printing image becomes lighter, yet very readable. NOTE: The EcoPrint setting has no effect on the print speed. EcoPrint setting is Off (default) EcoPrint setting is On ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 88
    factory setting is Fast 1200 mode.) 1 Press [MENU]. 2 Press U or V repeatedly until Print Quality > appears. Print Quality > 3 Press Z. 4 Press U or V repeatedly until >Resolution appears. >Resolution [OK]. 8 Press [MENU]. The message display returns to Ready. 2-60 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 89
    >Print Density appears. >Print Density 04 5 Press [OK]. A blinking question mark (?) appears. >Print Density ? 04 6 Select the print density from five steps from 01 (light) to 05 (dark) using U or V. 7 Press [OK]. 8 Press [MENU]. The message display returns to Ready. ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 90
    4 Options. • Reading Font Data • Reading Data • Writing Data • Deleting Data • Formatting Memory card • Printing of List of Partitions Reading Font Data If a memory card with the font data is already inserted into the slot when the printer is turned on, the fonts are automatically read into the
  • Kyocera 9530DN | Operation Guide - Page 91
    use the procedure explained later in this section to print a list of data names for confirmation. To write data to a memory card, proceed as follows. First check that the memory card is properly formatted. Otherwise on the display. Refer to Formatting on page 2-66. ADVANCED OPERATION GUIDE 2-63
  • Kyocera 9530DN | Operation Guide - Page 92
    partition name) which the printer automatically assigns one after another as follows: DataS001 (first data), DataS002 (second instructs the printer to automatically print out a memory card write information page as shown below. FS-9530DN Page Printer WRITE INFORMATION 2-64 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 93
    the memory card write information page is printed, the message display returns to Ready. If the writing is not completed successfully, an error code appears on the message display. For details, refer to Error Messages on page 4-10 in the Operation Guide. If this happens, press [GO]. The message
  • Kyocera 9530DN | Operation Guide - Page 94
    it can be used in the printer. Formatting deletes any existing data printer automatically prints out a format information page. FS-9530DN Page Printer printer uses for its system. Free Space: The space remaining in the memory card for storing data. When the memory card format information is printed
  • Kyocera 9530DN | Operation Guide - Page 95
    mark (?) appears. >Print Partition List? 6 Press [OK]. Processing appears and the printing of the list starts. FS-9530DN Page Printer PARTITION LIST Device Information file names (partition list) for the memory card is printed, the message display returns to Ready. ADVANCED OPERATION GUIDE 2-67
  • Kyocera 9530DN | Operation Guide - Page 96
    up to 16 characters. Installing the USB flash memory into the printer allows you to perform the following operations. • Printing PDF Data • Disconnecting a USB Memory Device • Printing a List of Data Names (partitions) Printing PDF data To print data stored in USB memory, proceed as follows. NOTE
  • Kyocera 9530DN | Operation Guide - Page 97
    printer, be sure to proceed with this menu to ensure safe disconnection. NOTE: If you remove USB memory without performing this operation, an error The message display returns to Ready. Disconnect the USB memory from the printer. Printing a List of Data Names (Partitions) 1 Press [MENU]. 2 Press
  • Kyocera 9530DN | Operation Guide - Page 98
    printed. FS-9530DN Page Printer PARTITION LIST After the USB memory partition list is printed 2-62. It also prints out the Directory Status List printer memory that can temporarily store print jobs. The RAM disk can be used only for electronic sorting. The stored print job can then be used to print
  • Kyocera 9530DN | Operation Guide - Page 99
    RAM disk in the printer's memory, first you must use the printer's menu selection system. The printer's menu selection system allows you to perform the following operations on the RAM disk. • Setting RAM Disk Size • Reading Data • Writing Data • Deleting Data • Printing of List of Partitions
  • Kyocera 9530DN | Operation Guide - Page 100
    as those of the memory card. Refer to the relevant sections in Using the CompactFlash Card on page 262. 12 Turn off and on the printer. RAM disk size becomes active. IMPORTANT:After turning the printer off, please wait at least five seconds before turning it on again. 2-72 ADVANCED OPERATION
  • Kyocera 9530DN | Operation Guide - Page 101
    . (This is the factory setting.) First Mode (Automatic Manual Feeding) The printer automatically feeds any paper placed on the MP tray even if another paper source is selected. After all paper in the MP tray is printed, paper will be fed from the paper source originally selected. 1 Press [MENU
  • Kyocera 9530DN | Operation Guide - Page 102
    to the paper size that is used to format the job to print. If they do not match, printing will not be made on the correct size paper when automatic paper size selection is made by the application (printer driver). The OufukuHagaki Env. Monarch Envelope #10 Envelope #9 2-74 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 103
    can automatically select the paper cassette according to the selection made by the application (printer driver). The factory default setting is Plain. For more details about the paper types that can be Plain Transparency Preprinted Labels Bond Recycled Vellum Rough ADVANCED OPERATION GUIDE 2-75
  • Kyocera 9530DN | Operation Guide - Page 104
    -750) is installed. If option paper feeders are added, Cassette1 Size and Cassette2 Size will appear for the standard paper cassette and Cassette3 Size, and Cassette4 Size will appear for the option paper feeders. 5 Press [MENU]. The message display returns to Ready. 2-76 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 105
    , the unit for some paper may be replaced with the example, when placing letter size paper in the cassette while mm unit paper feeder PF-700 as cassettes 3 and 4 using the same procedures. When using the paper Press U or V repeatedly until Paper Handling appears. Paper Handling > 3 Press Z. 4
  • Kyocera 9530DN | Operation Guide - Page 106
    type fed from the paper cassette of the printer. If the media type is set correctly, you can perform printing using the media type selection function from the application (printer driver). The factory default press [OK]. 8 Press [MENU]. The message display returns to Ready. ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 107
    the paper. The duplex unit is installed underneath the printer. You can automatically print on both sides of the paper. Duplex printing is available for the following paper types: Plain Preprinted Bond Recycled Letterhead Color Prepunched High quality Custom 1 (to 8) ADVANCED OPERATION GUIDE 2-79
  • Kyocera 9530DN | Operation Guide - Page 108
    be fed from the MP tray does not match the paper size and paper type of the current paper feed source cassette, a paper jam may occur. Binding Mode The term binding refers to the manner in which printed pages of paper are joined together (by gluing, stitching, etc.) in book form. The two possible
  • Kyocera 9530DN | Operation Guide - Page 109
    printer's top tray (face-down) or to the optional document finisher's output tray. 1 Press [MENU]. 2 Press U or V repeatedly until Paper Handling > appears. Paper changes depending on an installed option. 7 When the desired paper source is displayed, press [OK]. 8 Press [MENU]. The message
  • Kyocera 9530DN | Operation Guide - Page 110
    setting of Off, the paper size of the paper source is matched to the paper size formatting the jobs. If these differ, a corresponding error message is displayed. When this is set to On, printing is performed even if the actual paper size differs from the paper size formatting the jobs. 1 Press
  • Kyocera 9530DN | Operation Guide - Page 111
    the Paper Weight You can set the paper thickness for your custom paper type to be customized. 1 Display the custom paper type (refer to Creating Custom Paper Type on page 2-82) and press Z. 2 Press U or V repeatedly until >>Paper Weight appears. >>Paper Weight Normal 1 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 112
    paper type, refer to Media Type on page 1-13. Paper 5 When the desired paper thickness displayed, press [ printing as follows. The default setting is Enable. 1 Display the custom paper type (refer to Creating Custom Paper of the default setting for each paper type, refer to Media Type on
  • Kyocera 9530DN | Operation Guide - Page 113
    are set in Creating Custom Paper Type on page 2-82. 1 Press [MENU]. 2 Press U or V repeatedly until Paper Handling > appears. Paper Handling > 3 Press Z. appears. >Reset Type Adjust ? 6 Press [OK]. All the customized paper weight and duplex path settings will be reset to the default. The
  • Kyocera 9530DN | Operation Guide - Page 114
    printed by your printer for confirmation whenever necessary. The total number of printed pages can also be checked on the status page. Displaying the Total Printed >Printed Pages appears. >Printed Pages 0000001 5 Press [MENU]. The message display returns to Ready. 2-86 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 115
    Setting • Received Data Dumping • Restart Printer • Resource Setting • Alarm (Buzzer) Setting • Auto Continue Setting • Finishing • Service Menu (for service personnel) Selecting the Message Language You English Francais Deutsch Italiano Nederlands Español Português ADVANCED OPERATION GUIDE 2-87
  • Kyocera 9530DN | Operation Guide - Page 116
    sleep timer to conserve power when the printer is not printing, processing, or receiving data. You can turn off the sleep timer function by following the procedure given below. 1 Press [MENU]. 2 Press U or V repeatedly until Others > appears. Others > 3 Press Z. 2-88 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 117
    display returns to Ready. Sleep Timer Timeout Time You can adjust the timer value, the length of time the printer waits before entering sleeping mode in the absence of data. 1 Press [MENU]. 2 Press U or V [OK]. 8 Press [MENU]. The message display returns to Ready. ADVANCED OPERATION GUIDE 2-89
  • Kyocera 9530DN | Operation Guide - Page 118
    , the message Waiting will appear. Press [GO] to finish printing. Printer Resetting The procedure described below resets the printer's temporary conditions, such as the current unit of measurement, page orientation, font, character code set, margins, etc., set by commands to their default values
  • Kyocera 9530DN | Operation Guide - Page 119
    printer is resetting itself, then Please Wait followed by Ready. Self test Please Wait Ready Resource Protection When you switch from the PCL 6 emulation to another, all downloaded . Off 5 Press [OK]. A blinking question mark (?) appears. >Resource Prot. ? Off ADVANCED OPERATION GUIDE 2-91
  • Kyocera 9530DN | Operation Guide - Page 120
    paper supply is exhausted, or when paper jamming occurs, an audio warning is made to sound according to the status. This is useful, for example, when the printer items (e.g., Error) are displayed in the message display. Press U or V to >Error display each setting item. On Error Ready Job End
  • Kyocera 9530DN | Operation Guide - Page 121
    the following errors occurs: Memory overflow Press GO Print overrun Press GO KPDL error Press GO File not found Press GO RAM disk error Press GO the above errors is caused by someone on a network where the printer is being shared, for example, data sent from another person will be printed after a
  • Kyocera 9530DN | Operation Guide - Page 122
    [OK]. A blinking cursor (_) appears. >>Error Clear Timer 030sec. 7 Press U or V to increase or decrease the value of the figure where the cursor is blinking and set the desired time. The time must be set between 000 and 495 seconds, in 5-second increments. If set to 000, printing will be continued
  • Kyocera 9530DN | Operation Guide - Page 123
    installed on the printer. Duplex Printing Error Detection Setting This setting controls whether or not the message Duplex disabled Press GO appears when label or some other type of paper that is not supported for duplex printing is specified as the paper type when duplex printing is being performed
  • Kyocera 9530DN | Operation Guide - Page 124
    [GO], the printer continues printing without stapling. Add Staples is displayed, but printing continues Off without stapling. 1 Press [MENU]. 2 Press U or V repeatedly until Others > appears. Others > 3 Press Z. 4 Press U or V repeatedly until > Finishing Error > appears. >Finishing
  • Kyocera 9530DN | Operation Guide - Page 125
    Punch Error Detection Setting This setting is possible only when the Punch Unit is installed on the optional finisher unit. This setting controls whether or not the message Check chad box Press GO appears when the chad box on the punch unit becomes full. Message is displayed and printing pauses
  • Kyocera 9530DN | Operation Guide - Page 126
    The service menu contains maintenance operations to be performed by service personnel. The Print Status Page, Developer, and Drum menus appear; however, in general, you will only need to use the Print Status Page menus. Printing the Service Status Page The service status page contains printer
  • Kyocera 9530DN | Operation Guide - Page 127
    3 Fonts This chapter contains explanations on the following: • List of Fonts 3-2 ADVANCED OPERATION GUIDE 3-1
  • Kyocera 9530DN | Operation Guide - Page 128
    3 compatible fonts, as well as 1 bitmap font. You can print the font list from the printer by using the printer's operation panel key. To print a list of fonts, refer to Printing a List of Fonts on page 2-49. Fonts may be downloaded to the printer's memory from an option memory card or hard disk
  • Kyocera 9530DN | Operation Guide - Page 129
    PCL (Scalable and Bitmap) Fonts Fonts ADVANCED OPERATION GUIDE 3-3
  • Kyocera 9530DN | Operation Guide - Page 130
    Fonts KPDL Fonts (1) 3-4 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 131
    KPDL Fonts (2) Fonts ADVANCED OPERATION GUIDE 3-5
  • Kyocera 9530DN | Operation Guide - Page 132
    Fonts 3-6 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 133
    4-6 • Hard Disk 4-8 • CompactFlash (Memory) Card 4-10 • USB Flash Memory 4-11 • Expansion Memory Modules 4-12 • HDD Security Function 4-15 For availability of the options, consult your service technician. ADVANCED OPERATION GUIDE 4-1
  • Kyocera 9530DN | Operation Guide - Page 134
    Expansion Memory (DIMM 128/256/512 MB) Hard Disk Unit Document Finisher DF-730 Document Finisher DF-710 Mail Box MT-710 (for DF-710) Adapter Kit AK-705 * Required when installing DF-710 and DF-730 to this printer Paper Feeder PF-700 Paper Feeder PF-750 Booklet Folder BF-710 Punch Unit PH-5A
  • Kyocera 9530DN | Operation Guide - Page 135
    Cards Along with the standard for the network interface on the printer, the network interface card supports TCP/IP, IPX/SPX, NetBEUI and AppleTalk protocols, so that the printer can be used on network environments including Windows, Macintosh, UNIX, NetWare, etc. Network interface card IB-21E IB-23
  • Kyocera 9530DN | Operation Guide - Page 136
    set functions. It is installed to the left side of the printer. DF-730 DF-710 Document Finisher 3 output trays as standard with 3,000, 200 and 50 -710 Document Finisher and can punch holes automatically in printed out paper. Mail Box MT-710 for DF-710 It mounts on top of the DF-710 Document Finisher
  • Kyocera 9530DN | Operation Guide - Page 137
    for directly printing out PDF data inserts in the USB memory connector on the right side of the printer. Consult your dealer for USB memory usable with the printer. Data Security Kit (C) Activates the HDD security function. This kit is attached to the printer by the service representative. For
  • Kyocera 9530DN | Operation Guide - Page 138
    Options Network Interface The FS-9130DN/FS-9530DN have the standard Network interface. This printer supports the TCP/IP, IPX/SPX, NetBEUI, and AppleTalk protocols, so the network printing under various platforms such as Windows, Macintosh, UNIX, and NetWare is available. An option network interface
  • Kyocera 9530DN | Operation Guide - Page 139
    4 Connect the network cable. Options 5 Set the network address from the printer operation panel (for details about the modes,refer to Changing Network Interface Parameters on page 2-37). ADVANCED OPERATION GUIDE 4-7
  • Kyocera 9530DN | Operation Guide - Page 140
    Hard Disk Insert the hard disk into option hard disk unit slot on the printer. If a hard disk unit is installed in the printer, received data can be rasterized and stored on this hard disk. This enables high-speed printing of multiple copies using an electric sort function. Also, you can use the
  • Kyocera 9530DN | Operation Guide - Page 141
    Options 4 Tighten the two screws to secure the hard disk unit to the main circuit board. ADVANCED OPERATION GUIDE 4-9
  • Kyocera 9530DN | Operation Guide - Page 142
    printer. A memory card is a microchip card that may contain option fonts, macros, forms, etc. The printer reads the contents of the card into its internal memory when printer If the memory card is removed while the printer is on, damage could result in the printer's electronics or the memory card. 2
  • Kyocera 9530DN | Operation Guide - Page 143
    side of the printer. You can then print PDF data stored in the USB memory. Consult your dealer for USB flash memory usable with the printer. 1 Insert the from the printer, be sure to perform Remove Device in the USB Memory operation menu to ensure safe disconnection. ADVANCED OPERATION GUIDE 4-11
  • Kyocera 9530DN | Operation Guide - Page 144
    Options Expansion Memory Modules To expand the printer memory for more complex print jobs and faster print speed, you can plug in optional memory module (dual in line memory module) in the memory slot provided on the printer main controller board. You can select additional memory module from 64,
  • Kyocera 9530DN | Operation Guide - Page 145
    Options 2 Remove the screw from the memory slot cover at the back of the printer and remove the memory slot cover. 3 Remove the DIMM from its package. 4 Open the clips on both ends of in the socket. Clamp Clamp 6 Close the clips of the DIMM socket to secure the DIMM. ADVANCED OPERATION GUIDE 4-13
  • Kyocera 9530DN | Operation Guide - Page 146
    Print Status Page appears. 4 Press [OK] twice. 5 If the installation was successful, the amount of memory shown on the status page will correspond with the amount of expanded memory. (The factory installed memory size is 64 MB for FS-9130DN, 128 MB for FS9530DN.) 4-14 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 147
    Data Security Kit (C) need to be pre- installed. Overwrite Function The printer to install this security functions (hereinafter, the machine) by temporarily storing print jobs on an internal hard disk. Printing is method may take longer than the Once Overwrite. ADVANCED OPERATION GUIDE 4-15
  • Kyocera 9530DN | Operation Guide - Page 148
    printer temporarily stores print jobs on an internal hard disk. If the hard disk is stolen, there is a risk that the data might be passed to unauthorized parties or modified. The Security Kit question mark (?) appears. >Overwrite Mode Normal >Overwrite Mode ? Normal 4-16 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 149
    data.) 7 Press [OK]. 8 Press [MENU]. The display returns to Ready. NOTE: When the printer is overwriting data while Ready is displayed, Ready and Overwriting appear alternately in the message display. When is completed, the display returns to >Secure Format. ADVANCED OPERATION GUIDE 4-17
  • Kyocera 9530DN | Operation Guide - Page 150
    Options 7 Press [MENU]. The display returns to Ready. 4-18 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 151
    5 Computer Interface This chapter contains explanations on the following topics: • General Information 5-2 • Parallel Interface 5-3 • USB Interface 5-5 • Serial Interface (Option 5-6 • RS-232C Protocol 5-7 • RS-232C Cable Connection 5-10 ADVANCED OPERATION GUIDE 5-1
  • Kyocera 9530DN | Operation Guide - Page 152
    Interface General Information This chapter explains the signals used in the printer's parallel, USB, and serial (option) interfaces. It also lists pin assignments, signal functions, timings, connector specifications, and voltage levels. This chapter explains the following topics: • Parallel
  • Kyocera 9530DN | Operation Guide - Page 153
    Modes on page 2-35. NOTE: Use a parallel printer cable that complies with the IEEE1284 standard. You can Data 6 [Data 7] 9 In Data 7 [Data 8] Description A negative-going-strobe pulse causes the printer to read and latch the data on the Data 0 [1] to Data 7 [8] signal lines. These eight
  • Kyocera 9530DN | Operation Guide - Page 154
    Acknowledge* [nAck] Busy [Busy] Paper Empty [PError] Online (Select) [ Error error status.** Not used Not used This signal goes high when the printer is powered on. When this line is high, IEEE1284 mode is enabled. * Indicates signals that are low active. ** The Paper Empty, Online, and Error
  • Kyocera 9530DN | Operation Guide - Page 155
    printer supports the Hi-Speed USB (Universal Serial Bus) interface specifications and interface signals are as follows. Specifications Basic specification Complies with the Hi-Speed USB Connectors Printer (+5 V) Data transmission Data transmission Signal ground Shield ADVANCED OPERATION GUIDE 5-5
  • Kyocera 9530DN | Operation Guide - Page 156
    outgoing with respect to the printer. Pin In or out Signal printer frame. Transmit Data. This pin is used to output asynchronous data sent from the printer the computer to the printer. Request To Send. status of the printer buffer (i.e., nearly to EIA RS-232C specifications. The voltage level of
  • Kyocera 9530DN | Operation Guide - Page 157
    set of rules the computer follows in sending data to the printer. They are indicated on the status page. Parameters can be to Changing Serial Interface Modes on page 2-36. The parameters and their identification codes are given below. • H1: Baud rate • H2: Number of data ADVANCED OPERATION GUIDE 5-7
  • Kyocera 9530DN | Operation Guide - Page 158
    size This is the size of the input buffer, specified in units of 10 Kbytes. The factory-set value is 6, meaning 60 Kbytes. 5-8 ADVANCED OPERATION GUIDE
  • Kyocera 9530DN | Operation Guide - Page 159
    an error occurs on the serial interface. The following table summarizes the error status corresponding to different D0 values. Timing of XON transfer to host while Ready or Waiting XON sent every 3 to 5 seconds XON not sent Serial interface error Error not resolved Error
  • Kyocera 9530DN | Operation Guide - Page 160
    printer's RS-232C interface connector. 3 Plug the printer end of the RS-232C interface cable into the printer . 5 Switch on the printer's power. 6 The printer's RS-232C parameters are printer performs both of them simultaneously, using positive logic for DTR. If you are uncertain as to the printer
  • Kyocera 9530DN | Operation Guide - Page 161
    of client computers where it is not specifically necessary to assign a separate IP address to each client, including printers. EcoPrint This is a printing mode that controls toner consumption. Pages printed in the Ecoprint mode are lighter than pages printed in the normal mode. The default setting
  • Kyocera 9530DN | Operation Guide - Page 162
    printing. Printer driver The printer driver makes it possible for you to print data created using application software. The printer driver for the printer is on the Kyocera Mita Software Library CD-ROM supplied with the printer. Install the printer driver interfaces. This printer supports Hi-Speed
  • Kyocera 9530DN | Operation Guide - Page 163
    2-92 Auto error clear changing recovery time 2-94 how to set 2-93 Automatic manual feeding 2-73 B Binding 2-80 C Carriage return how to select 2-56 Code job permanent code jobs 2-33 printing a code jobs 2-28 printing a list of code jobs 2-28 temporary code jobs 2-32 Colored paper 1-12 CompactFlash
  • Kyocera 9530DN | Operation Guide - Page 164
    printing lists function 4-15 I Indicators interface 2-5 paper size 2-5 paper type 2-7 Ready, Data, Attention status page 2-21 Menu map how to print 2-19 sample 2-19 Menu selection system first mode 2-73 loading paper 1-18 paper sizes 1-4 paper types 1-13 setting the paper size 2-74 setting the paper
  • Kyocera 9530DN | Operation Guide - Page 165
    2-36 computer interface 5-10 protocol, RS-232C 5-7 signals and definitions 5-6 Service status page 2-98 Sleep mode Glossary-2 Sleep timer setting the timer 2-88 setting timeout time 2-89 Special paper 1-9 Specifications paper 1-3 Status page how to print 2-20 ADVANCED OPERATION GUIDE Index-3
  • Kyocera 9530DN | Operation Guide - Page 166
    /writing data 2-63 T Thick paper 1-12 Toner container 2-4, 2-22 Top tray 2-81 Transparency 1-10 U USB flash memory 2-68 description 2-68 printing a list of partitions 2-69 printing PDF 2-68 removing USB memory 2-69 USB interface pin assignment 5-5 specifications 5-5 V Virtual mailbox functions 2-24
  • Kyocera 9530DN | Operation Guide - Page 167
    A1
  • Kyocera 9530DN | Operation Guide - Page 168
  • Kyocera 9530DN | Operation Guide - Page 169
    2006 is a trademark of Kyocera Corporation
  • Kyocera 9530DN | Operation Guide - Page 170
    Rev. 1.1 2006.10
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
Advanced Operation Guide
FS-9130DN
FS-9530DN