LG DLE2350W Owner's Manual - Page 26

Duct Condition Test

Get LG DLE2350W PDF manuals and user guides
UPC - 048231011358
View all LG DLE2350W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

DUCT CONDITION TEST Your dryer features FlowSenseTM, an innovative sensing system that automatically detects blockages and restrictions in dryer ductwork. Keeping ductwork clean of lint buildup and free of restrictions allows clothes to dry faster and reduces energy use. NOTE: When the dryer is first installed, this test should be performed to alert you to any existing problems with the exhaust duct in your home. However, since the test performed during normal operation provides more accurate information on the condition of the exhaust duct than does the installation test, the number of bars displayed during the two tests may not be the same. To activate the duct condition test : NOTE: Dryer heating test must be performed before proceeding. Then perform the duct condition test below: 1 Press and hold the SIGNAL ON/OFF and TEMP. CONTROL buttons at the same time. While holding these buttons, press POWER ON/OFF. Correct Venting Restricted or Blocked Airflow Avoid long runs or runs with multiple elbows or bends. 2 The dryer will show in the number display to indicate that it is in duct condition testing mode. 3 Press START/PAUSE. The dryer will run for approximately 2 minutes to test for blockages or restrictions to air flow in the ductwork. If no bars are shown in the display, the ductwork is free from blockages or restrictions. If all bars are lit, the dryer ductwork has a blockage that needs to be removed immediately. IMPORTANT: Do NOT interrupt the test cycle! NOTE : Even if no bars are displayed during the duct condition test, some restrictions may still be present in the exhaust dust. Refer to pages 14-15 for more information. 26 Check for blockages and lint buildup. Make sure the ductwork is not crushed or restricted.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
Your dryer features FlowSense
TM
, an innovative
sensing system that automatically detects blockages
and restrictions in dryer ductwork. Keeping ductwork
clean of lint buildup and free of restrictions allows
clothes to dry faster and reduces energy use.
NOTE:
When the dryer is first installed, this test
should be performed to alert you to any existing
problems with the exhaust duct in your home.
However, since the test performed during normal
operation provides more accurate information on
the condition of the exhaust duct than does the
installation test, the number of bars displayed during
the two tests may not be the same.
To activate the duct condition test :
NOTE:
Dryer heating test must be performed before
proceeding. Then perform the duct condition test
below:
DUCT CONDITION TEST
Correct Venting
Restricted or Blocked Airflow
Avoid long runs or runs with multiple elbows
or bends.
Check for blockages and lint buildup.
Make sure the ductwork is not crushed
or restricted.
Press and hold the SIGNAL ON/OFF and
TEMP. CONTROL buttons at the same time.
While holding these buttons, press POWER
ON/OFF.
1
IMPORTANT:
Do
NOT
interrupt the test cycle!
NOTE : Even if no bars are displayed during the
duct condition test, some restrictions may still be
present in the exhaust dust. Refer to pages 14-15
for more information.
If no bars are shown in the display, the
ductwork is free from blockages
or restrictions.
If all bars are lit, the dryer ductwork has
a blockage that needs to be removed
immediately.
3
Press START/PAUSE. The dryer
will run for approximately 2
minutes to test for blockages
or restrictions to air flow in the
ductwork.
The dryer will show
in the number display
to indicate that it is in duct condition testing
mode.
2
26