LG DLE2516 Owners Manual - Page 18

Review, the following, options, to determine, the appropriate, electrical, connection, for your home - dryer reviews

Get LG DLE2516 PDF manuals and user guides View all LG DLE2516 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Review the following options to determine the appropriate electrical connection for your home: Use the instructions in this section if your home has a 4-wire receptacle (NEMA type 14-30R) and you will be using a UL listed, 1201240 volt minimum, 30 amp, dryer power supply cord. Use the instructions in this section if your home has a 3-wire receptacle (NEMA type 10-30R) and you will be using a UL listed, 1201240 volt minimum, 30 amp, dryer power supply cord. If this type is available at your home. you will be connecting to a fused disconnect or circuit breaker box. Warning : Grounding through the neutral conductor is prohibited tk_r(1) new branch-circuit installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductor. Failure to do so can result in fire or electrical shock. Prepare minimum 5 ft (1.52 m) of length in order tk_r dryer to be replaced. First, peel 5 inches (12.7 cm) of covering material from end. Strip 5 inches of ground wire insulation. Alter cutting 1% inch (3.8 cm) from 3 other wires peel insulation back 1 inch (2.5 cm). Make ends of 3 wires a hook shape. r_.; Then, put the hooked shape end of the wire under the screw of the terminal block (hooked end facing to the right) and pinch the hook together and screw tightly. If this type is available at your home. you will be connecting to a fused disconnect or circuit breaker box. • Connect the power supply wire to the terminal block. Colored wire should be connected to same color screw. Wire color indicated on manual is connected to the same color screw in block. Otherwise,a short or excessive current flow may result. 18 1. Connect neutral wire (white) of power cord to center terminal block screw. 2. Connect red and black wires to the left and right terminal block screws. 3. Connect _round wire (green) of power cord to external ground screw and move neutral ground wire of appliance and connect it to center screw. 4. Make sure that the strain relief screw is tightened. Be sure that all terminal block nuts are on tight and power cord is in right position. Center terminal block screw (silver) Neutral 9rounding wire (white) Neutral wire (white or center wire) Strain relief Green wire of power cord External ground connector

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
Review
the following
options
to determine
the appropriate
electrical
connection
for your home:
Use the instructions
in this section if your home has
a 4-wire receptacle (NEMA type 14-30R) and you
will be using a UL listed, 1201240 volt minimum,
30 amp, dryer power supply cord.
Use
the
instructions
in this
section
if your
home
has
a 3-wire
receptacle
(NEMA
type
10-30R)
and you
will be using
a UL listed,
1201240 volt
minimum,
30 amp,
dryer
power
supply
cord.
If this type
is available
at your
home.
you will
be
connecting
to a fused
disconnect
or circuit
breaker
box.
If this type
is available
at your
home.
you
will be
connecting
to a fused
disconnect
or circuit
breaker
box.
•
Connect the power supply wire to the terminal
block. Colored wire should be connected to
same color screw. Wire color indicated
on
manual is connected to the same color screw in
block.
Otherwise,a
short or excessive current
flow
may result.
18
Warning
: Grounding
through
the neutral
conductor
is
prohibited
tk_r(1) new branch-circuit
installations,
(2)
mobile
homes,
(3) recreational
vehicles,
and (4) areas
where
local codes prohibit
grounding
through
the
neutral
conductor.
Failure
to do so can result
in fire or
electrical
shock.
Prepare
minimum
5 ft (1.52 m) of length in order
tk_r
dryer to
be
replaced.
First, peel 5 inches (12.7 cm) of covering material from
end. Strip 5 inches of ground wire insulation.
Alter
cutting
1% inch (3.8 cm) from 3 other wires peel
insulation back
1 inch (2.5 cm). Make ends of 3 wires a
hook shape.
r_.;
Then,
put the hooked
shape end of the wire under
the
screw
of the terminal
block
(hooked
end facing
to the
right)
and pinch
the hook
together
and screw
tightly.
1. Connect
neutral
wire (white)
of power cord
to center
terminal
block
screw.
2. Connect
red and black wires to the left and right
terminal
block
screws.
3. Connect
_round
wire (green)
of power
cord to external
ground
screw and move
neutral
ground
wire of
appliance
and connect
it to center
screw.
4. Make
sure that the strain relief
screw
is tightened.
Be sure that all terminal
block
nuts are on tight and
power
cord is in right position.
Center
terminal
block
screw (silver)
Neutral
9rounding
wire (white)
Neutral
wire
(white
or center
wire)
Strain
relief
Green
wire of power
cord
External
ground
connector