LG LDF5545BD Additional Link - Owner s Manual - Page 21

Connecting Water Supply, Connecting Power

Get LG LDF5545BD PDF manuals and user guides View all LG LDF5545BD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

20 INSTALLATION Connecting Water Supply 1 Before connecting, turn off the water supply. 2 Slide the flexible stainless-steel water line or copper tube into the elbow. 3 Tighten the compression nut and make sure that the line is not kinked or pinched. Connecting Power Valve Water supply line NOTE ••During the final installation check of the dishwasher, an IE error code may appear on the display. Make sure the water line is not kinked and the water supply for the dishwasher has been turned on before calling for service. NOTE ••The best location for the electrical conduit is on the right side of the back wall. Re-route the power cable before installation if the electrical conduit pipe is longer than 3" (76 mm) and is centered on the back wall. 1 Before beginning, turn off electrical power to the unit at the circuit breaker. 2 Remove the junction box cover and then install the strain relief. 1 2 3 Twist the wire nuts tightly onto the wires; then wrap each connection with electrical tape. 1 2 3 4 4 Check again and make sure that all wires are connected correctly: black to black, white to white, green ground wire to green ground wire. 5 Replace the junction box cover. WARNING ••Verify that the black wire is hot (120 V). If not, or if you are unsure of the power supply, have it checked by a licensed electrician. CAUTION ••Do not leave stripped wire exposed. Trim stripped wire to fit completely inside wire nuts.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
20
INSTALLATION
Connecting Water Supply
1
Before connecting, turn off the water supply.
2
Slide the flexible stainless-steel water line or
copper tube into the elbow.
3
Tighten the compression nut and make sure that
the line is not kinked or pinched.
Valve
Water supply
line
NOTE
•
During the final installation check of the dishwasher,
an IE error code may appear on the display. Make
sure the water line is not kinked and the water
supply for the dishwasher has been turned on
before calling for service.
Connecting Power
NOTE
•
The best location for the electrical conduit is on the
right side of the back wall. Re-route the power cable
before installation if the electrical conduit pipe is
longer than 3" (76 mm) and is centered on the back
wall.
1
Before beginning, turn off electrical power to the
unit at the circuit breaker.
2
Remove the junction box cover and then install
the strain relief.
1
2
3
Twist the wire nuts tightly onto the wires; then
wrap each connection with electrical tape.
1
2
3
4
4
Check again and make sure that all wires are
connected correctly: black to black, white to
white, green ground wire to green ground wire.
5
Replace the junction box cover.
WARNING
•
Verify that the black wire is hot (120 V). If not,
or if you are unsure of the power supply, have it
checked by a licensed electrician.
CAUTION
•
Do not leave stripped wire exposed. Trim
stripped wire to fit completely inside wire nuts.