LG LFX25974SW Owner's Manual - Page 15

Assembling the Left Refrigerator Door

Page 15 highlights

Assembling the Left Refrigerator Door Install the left refrigerator door after the right door is installed. INSTALLATION 15 ENGLISH 1 Lower the door onto the middle hinge pin. (2) (1) (3) (5) (4) (6) (7) (8) 2 Fit the top hinge (7) over the hinge lever latch (8) and into place. 3 Rotate the lever (6) clockwise to secure the hinge. 4 Install the grounding screws (5) and connect the two wire harnesses (4). 5 Push the water tube (3) located at the top of the left door into the hole beside the left hinge on the top of the cabinet until it exits through the back. 6 Insert the water supply tube (3) into the connector until you see only one scale mark. Fully insert the tub cover (15 mm). 7 Hook the tabs on the left side of the hinge cover (1) under the edge of the top hinge (7) and position the cover in place. 8 Insert and tighten the cover screw (1). 9 Insert the water supply tube at least 5/8 in. (15 mm) into the connector. 10 Hook the tab on the door switch side of the cover under the edge of the wire opening in the cabinet top. 11 Position the cover into place. Insert and tighten the cover screw. NOTE Collet Tube Insert Line Clip 1) Gently press the Collet and insert the tube until only one line shows on the tube. (Correct) (Incorrect) 2) Pull the tube to make sure that the tube is tightly fastened and then insert the clip.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49

ENGLISH
15
INSTALLATION
Assembling the Left Refrigerator Door
Install the left refrigerator door after the right door is installed.
1
Lower the door onto the middle hinge pin.
2
Fit the top hinge (7) over the hinge lever latch (8) and into
place.
3
Rotate the lever (6) clockwise to secure the hinge.
4
Install the grounding screws (5) and connect the two wire
harnesses (4).
5
Push the water tube (3) located at the top of the left door
into the hole beside the left hinge on the top of the cabi-
net until it exits through the back.
6
Insert the water supply tube (3) into the connector until
you see only one scale mark. Fully insert the tub cover
(15 mm).
7
Hook the tabs on the left side of the hinge cover (1) under
the edge of the top hinge (7) and position the cover in
place.
8
Insert and tighten the cover screw (1).
9
Insert the water supply tube at least 5/8 in.
(15 mm) into the connector.
10
Hook the tab on the door switch side of the cover under
the edge of the wire opening in the cabinet top.
11
Position the cover into place. Insert and tighten the cover
screw.
NOTE
Collet
Tube
Insert Line
Clip
1) Gently press the Collet and insert the tube until
only one line shows on the tube.
(Correct)
(Incorrect)
2)
Pull the tube to make sure that the tube is tightly
fastened and then insert the clip.
(2)
(1)
(3)
(4)
(5)
(6)
(7)
(8)