LG LP1210BXR Owner's Manual - Page 10

Using The Controls - not cooling

Get LG LP1210BXR PDF manuals and user guides
UPC - 048231363075
View all LG LP1210BXR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

HOW TO USE USING THE CONTROLS Control panel buttons shown. Operation using the remote control is the same, unless specifically noted.NOTE:The remote sensor is located under the air discharge and on the top of the front panel. POWER Press the POWER button to turn the air conditioner ON or OFF. When you turn the air conditioner on, an ascending tone will play and the LCD display will show the set temperature and any active mode.The air discharge on the top of the air conditioner wil automatically open. When turning the air conditioner off, you will hear a descending tone and the air discharge on the top of the air conditioner will close. Any control settings such as Mode, Set Temperature, Auto Swing, etc. will be retained in memory when the power is off. NOTE: When turned on after being unplugged, the air conditioner will automatically reset to COOL mode, with a temperature setting of 72°F. Any settings will need to be re-entered. Always point the remote at the sensor. The remote may not work if the sensor is in bright light or if there is not a clear path between the remote and the sensor. MODE Press the MODE button to select the operating mode (COOL, FAN,DRYor ENERGY SAVER) for the air conditioner.And you can see the active mode through the LCD Display. The default setting is COOL. Press the MODE button to change to FAN, press again to change to DRY, again to change to ENERGY SAVER,and again to return to COOL. Mode COOL FAN DRY Features Compressor runs and cools the room. Use the / and FAN buttons to set the desied temperature and circulation fan speed. Fan circulates air but compressor does not run. Use the FAN button to set the desired fan speed. Dry mode is used to remove humidity from the room without additional cooling. Once the set temperature is reached, the compressor and circulation fan turns off and only the exhaust fan will run. Fan speed is pre-set and cannot be adjusted. ENERGY Under normal operation, the exhaust fan cycles on SAVER and off with the compressor, and the circulation fan runs at the set speed. The mode helps reduce power consumption by automatically turning off the circulation fan as well as the exhaust fan when the compressor is off. The air conditioner will automatically cycle both fans on and off with the compressor as needed for cooling. 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
10
Press the
POWER
button to turn the air
conditioner ON or OFF. When you turn the air
c
tone will play and the LCD
display will show the set
temperature and any active
onditioner on, an ascending
mode.The air discharge on the top of the air
conditioner wil automatically open.
When turning the air conditioner off, you will
hear a descending tone and the air discharge
on the top of the air conditioner will close.
Any control settings such as Mode, Set
Temperature, Auto Swing, etc. will be retained
in memory when the power is off.
NOTE:
When turned on after being unplugged,
the air conditioner will automatically reset to
COOL mode, with a temperature setting of 72°F.
Any settings will need to be re-entered.
POWER
Control panel buttons shown. Operation
using the remote control is the same, unless
specifically noted.
NOTE:
The remote sensor is
located under the air discharge and on the top
of the front panel.
Always point the remote at the sensor. The
remote may not work if the sensor is in bright
light or if there is not a clear path between the
remote and the sensor.
Press the
MODE
button to select the operating
mode (COOL, FAN,DRYor ENERGY SAVER) for
the air conditioner.And you can
see the active mode through the
LCD Display.
The default setting is COOL.
Press the
MODE
button to
change to FAN, press again to change to DRY,
again to change to ENERGY SAVER,and again
to return to COOL.
MODE
USING THE CONTROLS
Mode
Features
COOL
Compressor runs and cools the room. Use the
/
and
FAN
buttons to set the desied
temperature and circulation fan speed.
FAN
Fan circulates air but compressor does not run.
Use the
FAN
button to set the desired fan speed.
DRY
Dry mode is used to remove humidity from the room
without additional cooling. Once the set temperature
is reached, the compressor and circulation fan turns
off and only the exhaust fan will run. Fan speed is
pre-set and cannot be adjusted.
ENERGY
SAVER
Under normal operation, the exhaust fan cycles on
and off with the compressor, and the circulation fan
runs at the set speed.
The mode helps reduce power
consumption by
automatically turning off the circulation fan as well
as the exhaust fan when the compressor is off. The
air conditioner will automatically cycle both fans on
and off with the compressor as needed for cooling.
HOW TO USE