Lenovo ThinkCentre Edge 62z Hardware Maintenance Manual (HMM) (Sept 2012) - Th - Page 85

Disconnect the optical drive cable from the optical drive

Get Lenovo ThinkCentre Edge 62z PDF manuals and user guides View all Lenovo ThinkCentre Edge 62z manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

This section provides instructions on how to replace the optical drive. Note: The optical drive is available only in some models. To replace the optical drive, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Place a soft, clean towel or cloth on the desk or other flat surface. Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up. 3. Remove the computer cover. See "Removing the computer cover" on page 75. 4. Remove the VESA mount bracket. See "Removing and reinstalling the VESA mount bracket" on page 75. 5. Locate the optical drive. See "Locating major FRUs and CRUs" on page 67. 6. Disconnect the optical drive cable from the optical drive, and remove the screw that secures the optical drive. Then, slide the optical drive to remove it from the optical drive bay. Figure 14. Removing the optical drive 7. To install a new optical drive, slide the new optical drive into the optical drive bay until the screw hole in the metal tab is aligned with that in the chassis. Figure 15. Installing the optical drive 8. Connect the optical drive cable to the optical drive, and install the screw to secure the optical drive. Chapter 9. Replacing FRUs 79

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
This section provides instructions on how to replace the optical drive.
Note:
The optical drive is available only in some models.
To replace the optical drive, do the following:
1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect
all power cords from electrical outlets and disconnect all cables that are connected to the computer.
2. Place a soft, clean towel or cloth on the desk or other flat surface. Hold the sides of your computer and
gently lay it down so that the screen is against the surface and the cover is facing up.
3. Remove the computer cover. See “Removing the computer cover” on page 75.
4. Remove the VESA mount bracket. See “Removing and reinstalling the VESA mount bracket” on page 75.
5. Locate the optical drive. See “Locating major FRUs and CRUs” on page 67.
6. Disconnect the optical drive cable from the optical drive, and remove the screw that secures the optical
drive. Then, slide the optical drive to remove it from the optical drive bay.
Figure 14. Removing the optical drive
7. To install a new optical drive, slide the new optical drive into the optical drive bay until the screw hole in
the metal tab is aligned with that in the chassis.
Figure 15. Installing the optical drive
8. Connect the optical drive cable to the optical drive, and install the screw to secure the optical drive.
Chapter 9
.
Replacing FRUs
79