Lenovo ThinkCentre Edge 62z Hardware Maintenance Manual (HMM) (Sept 2012) - Th - Page 95

Installing or replacing a memory module, Removing the screws that secure the inverter

Get Lenovo ThinkCentre Edge 62z PDF manuals and user guides View all Lenovo ThinkCentre Edge 62z manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

Figure 27. Removing the screws that secure the inverter 8. Disconnect the three cables from the inverter. 9. Lift the inverter off the computer. 10. To reinstall the new inverter, connect the three cables to the new inverter. Position the new inverter and align the two screw holes in the new inverter with those in the computer. 11. Install the two screws to secure the new inverter to the main bracket. 12. Reinstall the optical drive. See "Replacing the optical drive" on page 78. 13. Go to "Completing the parts replacement" on page 100. Installing or replacing a memory module Attention: Do not open your computer or attempt any repair before reading and understanding the "Important safety information" in the Safety, Warranty, and Setup Guide that came with your computer. To obtain a copy of the Safety, Warranty, and Setup Guide, go to: http://www.lenovo.com/support This section provides instructions on how to install or replace a memory module. Your computer has one memory slot for installing or replacing DDR3 SODIMM (small outline dual inline memory module). When installing or replacing a memory module, use a 2 GB, 4 GB or 8 GB DDR3 SODIMM. To install or replace a memory module, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Place a soft, clean towel or cloth on the desk or other flat surface. Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up. 3. Remove the computer cover. See "Removing the computer cover" on page 75. 4. Remove the VESA mount bracket. See "Removing and reinstalling the VESA mount bracket" on page 75. Chapter 9. Replacing FRUs 89

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Figure 27. Removing the screws that secure the inverter
8. Disconnect the three cables from the inverter.
9. Lift the inverter off the computer.
10. To reinstall the new inverter, connect the three cables to the new inverter. Position the new inverter and
align the two screw holes in the new inverter with those in the computer.
11. Install the two screws to secure the new inverter to the main bracket.
12. Reinstall the optical drive. See “Replacing the optical drive” on page 78.
13. Go to “Completing the parts replacement” on page 100.
Installing or replacing a memory module
Attention:
Do not open your computer or attempt any repair before reading and understanding the “Important safety information”
in the
Safety, Warranty, and Setup Guide
that came with your computer. To obtain a copy of the
Safety, Warranty,
and Setup Guide
, go to:
This section provides instructions on how to install or replace a memory module.
Your computer has one memory slot for installing or replacing DDR3 SODIMM (small outline dual inline
memory module). When installing or replacing a memory module, use a 2 GB, 4 GB or 8 GB DDR3 SODIMM.
To install or replace a memory module, do the following:
1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect
all power cords from electrical outlets and disconnect all cables that are connected to the computer.
2. Place a soft, clean towel or cloth on the desk or other flat surface. Hold the sides of your computer and
gently lay it down so that the screen is against the surface and the cover is facing up.
3. Remove the computer cover. See “Removing the computer cover” on page 75.
4. Remove the VESA mount bracket. See “Removing and reinstalling the VESA mount bracket” on page 75.
Chapter 9
.
Replacing FRUs
89