Lenovo ThinkPad R50 Greek - Service and troubleshooting guide for ThinkPad R50 - Page 23

Solving computer problems

Get Lenovo ThinkPad R50 PDF manuals and user guides View all Lenovo ThinkPad R50 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Solving computer problems Message Solution 0177: Bad SVP data, stop Checksum of the supervisor password in the EEPROM is not correct. The POST task. system board should be replaced. Have the computer serviced. 0182: Bad CRC2. Enter BIOS Setup and load Setup defaults. Checksum of the CRC2 setting in the EEPROM is not correct. Go to IBM BIOS Setup Utility. Press F9 and then Enter to load the default setting. Press F10 and then Enter to restart the system. 0185: Bad startup sequence settings. Enter BIOS Setup and load Setup defaults. Checksum of the startup sequence setting in the EEPROM is not correct. Go to IBM BIOS Setup Utility. Press F9 and then Enter to load the default setting. Press F10 and then Enter to restart the system. 0187: EAIA data access The access to EEPROM has failed. Have the computer serviced. error 0188: Invalid RFID The EEPROM checksum is not correct (block # 0 and 1). The system board serialization information should be replaced, and the box serial number needs to be reinstalled. Have area the computer serviced. 0189: Invalid RFID configuration information area The EEPROM checksum is not correct (block # 4 and 5). The system board should be replaced, and the UUID needs to be reinstalled. Have the computer serviced. 0190: Critical low-battery The computer turned off because the battery is low. Connect the ac adapter error to the computer and charge the battery, or replace the battery with a fully charged one. 0191: System Security Invalid remote change requested. The system configuration change has failed. Confirm the operation and try again. To clear the error, enter the IBM BIOS Setup Utility. 0192: System Security IBM Embedded Security hardware tamper detected. The Security Chip has been replaced with a different one. Have the computer serviced. 0199: System Security IBM Security password retry count exceeded. This message is displayed if you enter a wrong supervisor password more than three times. Confirm the supervisor password and try again. To clear the error, enter the IBM BIOS Setup Utility. 01C8: More than one modem devices are found. Remove one of them. Press to continue. Remove a Modem Mini-PCI Card. Otherwise, press Esc to ignore the warning message. If it does not solve this problem, have the computer serviced. 01C9: More than one Ethernet devices are found. Remove one of them. Press to continue. Your ThinkPad computer has a built-in Ethernet feature, and you cannot add another such feature by installing an Ethernet device. If this error message is displayed, remove the Ethernet device that you installed. Otherwise, press Esc to ignore the warning message. If this does not solve the problem, have the computer serviced. Chapter 2. Solving computer problems 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Message
Solution
0177: Bad SVP data, stop
POST task.
Checksum of the supervisor password in the EEPROM is not correct. The
system board should be replaced. Have the computer serviced.
0182: Bad CRC2. Enter
BIOS Setup and load
Setup defaults.
Checksum of the CRC2 setting in the EEPROM is not correct. Go to IBM
BIOS Setup Utility. Press F9 and then Enter to load the default setting. Press
F10 and then
Enter
to restart the system.
0185: Bad startup
sequence settings. Enter
BIOS Setup and load
Setup defaults.
Checksum of the startup sequence setting in the EEPROM is not correct. Go
to IBM BIOS Setup Utility. Press F9 and then
Enter
to load the default
setting. Press F10 and then
Enter
to restart the system.
0187: EAIA data access
error
The access to EEPROM has failed. Have the computer serviced.
0188: Invalid RFID
serialization information
area
The EEPROM checksum is not correct (block # 0 and 1). The system board
should be replaced, and the box serial number needs to be reinstalled. Have
the computer serviced.
0189: Invalid RFID
configuration
information area
The EEPROM checksum is not correct (block # 4 and 5). The system board
should be replaced, and the UUID needs to be reinstalled. Have the
computer serviced.
0190: Critical low-battery
error
The computer turned off because the battery is low. Connect the ac adapter
to the computer and charge the battery, or replace the battery with a fully
charged one.
0191: System Security -
Invalid remote change
requested.
The system configuration change has failed. Confirm the operation and try
again. To clear the error, enter the IBM BIOS Setup Utility.
0192: System Security -
IBM Embedded Security
hardware tamper
detected.
The Security Chip has been replaced with a different one. Have the
computer serviced.
0199: System Security -
IBM Security password
retry count exceeded.
This message is displayed if you enter a wrong supervisor password more
than three times. Confirm the supervisor password and try again. To clear
the error, enter the IBM BIOS Setup Utility.
01C8: More than one
modem devices are
found. Remove one of
them. Press <Esc> to
continue.
Remove a Modem Mini-PCI Card. Otherwise, press
Esc
to ignore the
warning message. If it does not solve this problem, have the computer
serviced.
01C9: More than one
Ethernet devices are
found. Remove one of
them. Press <Esc> to
continue.
Your ThinkPad computer has a built-in Ethernet feature, and you cannot
add another such feature by installing an Ethernet device. If this error
message is displayed, remove the Ethernet device that you installed.
Otherwise, press Esc to ignore the warning message. If this does not solve
the problem, have the computer serviced.
Solving computer problems
Chapter 2. Solving computer problems
13