Home » Lexmark Manuals » Laser Printers » Lexmark 21Z0294 » Manual Viewer

Lexmark 21Z0294 Technical Reference - Page 306

Standard Parallel Connector, Computer to Printer, Printer to Computer Advanced Status

UPC - 734646313247

Add to My Manuals
Save this manual to your list of manuals

Page 306 highlights

8-4 Interfaces Note: To reset your printer with an INIT* signal, set Honor Init to On from the printer control panel or through MarkVision Professional. See your printer documentation for more information. Your printer can communicate with a computer across the parallel interface in three ways: Computer to Printer This is typically how a computer and printer communicate. When the printer is receiving data from the computer, it can use either Standard or Fastbytes protocol. The burst transfer rate in Fastbytes is faster than in Standard protocol. For best throughput, use Fastbytes protocol. Printer to Computer (Advanced Status) Your printer can send data to the computer. This capability lets the printer send status messages to the computer on the parallel interface. Parallel Modes 1 and 2 These are printer features that enhance reliability of data transfer from the host computer to the printer. See "Parallel Mode 1" on page 8-10 and "Parallel Mode 2" on page 8-10 for more information. Standard Parallel Connector The standard IEEE 1284-B compliant parallel connector on the printer is a 36-pin D-shell female receptacle, as shown. 18 1 36 19

Section	Page
Contents	3
CHAPTER 1: Introduction	7
Overview	7
Bibliography	10
CHAPTER 2: PCL Emulation	11
Selecting PCL Emulation	11
Using SmartSwitch	11
Using the Printer Control Panel or MarkVision Professional	11
Using Your Software Program	12
Page Formatting	12
Printable Areas	12
Lexmark C935	13
Lexmark X940e and X945e	15
Print Area Menu Item	17
Font and Symbol Set Support for the Lexmark C935, X940e, and X945e	19
Forward and Backward Compatibility Modes for the Lexmark C935, X940e, and X945e	20
Selecting Symbol Sets for LexmarkC935, X940e, and X945e	24
Command Structure	59
Control Codes	59
Commands	60
PCL Emulation Commands	63
PCL Emulation Commands by Function	63
GL/2 Commands	85
Raster Image Graphics	89
Raster Compression Mode	89
Macros	96
CHAPTER 3: Printer Job Language	97
PJL Command Notation	97
Kernel Commands	98
Job Separation Commands	100
Environment Commands and Variables	103
Common Variables for PCL Emulation	136
Status Readback Commands	142
Status Message Format	149
Information Messages	149
Auto-Continuable Conditions	151
Attendance Conditions	155
Operator Intervention - Paper Handling	160
Operator Intervention - Paper Jams	163
Service Errors	167
Device Attendance Commands	168
Unique PJL Commands	170
File Commands for Flash or Disk	174
File and Device Protection Commands	181
Protecting a File or Device	181
Unlocking a Protected File or Device	183
Re-Locking a Protected File or Device	184
Unlocking a Protected File or Device for the Current Job	185
Recovering Lost Passwords	186
CHAPTER 4: PostScript Emulation	187
Selecting PostScript Emulation	187
Using SmartSwitch	187
Using the Printer Control Panel or MarkVision Professional	187
Using Your Software Program	188
Paper Tray Support	190
Envelope Size Support	195
Envelope Tray Support	197
Supplemental Operator Summary	199
Page Device Parameters	234
Interpreter Parameters	248
User Parameters	248
System Parameters	251
Device Parameters	257
Status and Error Messages	278
Tagged Binary Not Active	278
Tagged Binary Active	278
Status Messages	279
CHAPTER 5: Switching Languages	280
SmartSwitch	280
Setting SmartSwitch for Different Interfaces	281
Printer Job Language	281
Sniffing	282
CHAPTER 6: Flash Memory and Disk	283
Resource Data Collection (Download Target)	284
Storing Resources on Flash Memory or Disk	285
Viewing the Contents of Flash Memory and Disk	285
Password Protection	289
Rewriting the Flash Content	290
Accessing Files with PostScript Emulation	291
File Naming Conventions	291
Device Search Order	294
Performance	295
Job Buffering	295
Creating a Partition	296
Enabling Job Buffering	296
Disabling Job Buffering	297
Recovering from a Power Loss	297
CHAPTER 7: Printer Specifications	298
Airflow Requirement	298
Noise Emission Levels	298
Electrical Specifications	299
Power Requirements	299
Physical Specifications	300
Clearance Requirements	301
Environmental Conditions	302
Altitude Specifications	302
Atmospheric Pressure	302
CHAPTER 8: Printer Interfaces	303
Setting Up the Communications Port	304
Setting Up the Communications Port	304
Deciding Which Interface to Use	305
Parallel Interface	305
Standard Parallel Connector	306
Using the INIT* Signal to Initialize	307
Computer-to-Printer Communications	307
Printer-to-Computer Communication (Advanced Status)	311
Parallel Mode 1	312
Parallel Mode 2	312
Using the RS-232C Serial Interface	313
Network Support	322
Input Buffer	323
APPENDIX A: PCL Support	325
APPENDIX B: PJL Support	334
APPENDIX C: PostScript Support	365

Match case Limit results 1 per page

Interfaces

8-4

Note:

To reset your printer with an INIT* signal, set Honor Init to On from the printer

control panel or through MarkVision Professional. See your printer

documentation for more information.

Your printer can communicate with a computer across the parallel interface in three

ways:

Computer to Printer

This is typically how a computer and printer communicate. When the printer is

receiving data from the computer, it can use either

Standard

Fastbytes

protocol.

The burst transfer rate in Fastbytes is faster than in Standard protocol. For best

throughput, use Fastbytes protocol.

Printer to Computer (Advanced Status)

Your printer can send data to the computer. This capability lets the printer send status

messages to the computer on the parallel interface.

Parallel Modes 1 and 2

These are printer features that enhance reliability of data transfer from the host

computer to the printer. See “Parallel Mode 1” on page 8-10 and “Parallel Mode 2” on

page 8-10 for more information.

Standard Parallel Connector

The standard IEEE 1284-B compliant parallel connector on the printer is a 36-pin

D-shell female receptacle, as shown.