Lexmark E360DN Technical Reference - Page 13

PostScript paper tray support, Tray selected with tray operators - manual

Get Lexmark E360DN - Hv Taa/gov Compliant PDF manuals and user guides
UPC - 734646084475
View all Lexmark E360DN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

PostScript paper tray support When the printer receives one of the operators listed in "Tray selected with tray operators" on page 13, it performs the actions listed as follows. This paper tray selection process ends as soon as a suitable paper source is chosen and paper is fed from this tray. • The printer checks the value of manualfeed in statusdict and the ManualFeed page device parameter. If either one is true, the printer sends a message to load the requested size in the manual feed tray or multipurpose feeder. • The PageSize Policy is set to 2 by means of setpagedevice. • The printer checks the paper size loaded in the current active source to determine if it matches the requested size. If the sizes match, the paper is fed from the active source. Note: The current active tray is the last source that was selected from the printer control panel or by the printer language. • If the requested size and the size loaded in the active source do not match, the sources are searched in the order defined by the Priority array in the InputAttributes dictionary in the pagedevice dictionary. • If the requested media size is not found by the previous search, the following search order is used: - Tray 1 - Multipurpose Feeder/Manual Feeder • If the requested size cannot be located in any automatic source, a configurationerror is issued and the job is flushed. For printers that support automatic duplexing: • Automatic duplexing is not supported for custom-size paper or for envelopes in the multipurpose feeder. Automatic duplexing is supported from the multipurpose feeder for all other papers. • If the paper source is changed before the back side of a duplexed page prints, a blank back page prints, the paper source changes, and the information for the back side of the page is printed on the front side of a page sent from the new paper source. When these operators are used, it is equivalent to executing the following PostScript emulation sequence: >> setpagedevice where x y are the PageSize in points. Tray selected with tray operators = Supported X = Not supported Operator Tray selected (corresponding image size is set) a3tray tray with A3-size paper a4tray tray with A4-size paper a5tray tray with A5-size paper b4tray b5tray tray with B4-size paper tray with B5-size paper Printer models E260, E260d/dn, E360d/dn, E460dn/dw X203n MFP, X204n MFP X X X X PostScript (PS) emulation 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
PostScript paper tray support
When the printer receives one of the operators listed in “Tray selected with tray operators” on page 13, it performs
the actions listed as follows. This paper tray selection process ends as soon as a suitable paper source is chosen and
paper is fed from this tray.
•
The printer checks the value of
manualfeed
in
statusdict
and the ManualFeed page device parameter. If either
one is true, the printer sends a message to load the requested size in the manual feed tray or multipurpose feeder.
•
The PageSize Policy is set to 2 by means of
setpagedevice
.
•
The printer checks the paper size loaded in the current active source to determine if it matches the requested
size. If the sizes match, the paper is fed from the active source.
Note:
The current active tray is the last source that was selected from the printer control panel or by the printer
language.
•
If the requested size and the size loaded in the active source do not match, the sources are searched in the order
defined by the Priority array in the InputAttributes dictionary in the pagedevice dictionary.
•
If the requested media size is not found by the previous search, the following search order is used:
–
Tray 1
–
Multipurpose Feeder/Manual Feeder
•
If the requested size cannot be located in any automatic source, a
configurationerror
is issued and the job is
flushed.
For printers that support automatic duplexing:
•
Automatic duplexing is not supported for custom-size paper or for envelopes in the multipurpose feeder.
Automatic duplexing is supported from the multipurpose feeder for all other papers.
•
If the paper source is changed before the back side of a duplexed page prints, a blank back page prints, the paper
source changes, and the information for the back side of the page is printed on the front side of a page sent from
the new paper source.
When these operators are used, it is equivalent to executing the following PostScript emulation sequence:
<< /PageSize [x y]/ImagingBBox null /Policies << /PageSize 2>> >>
setpagedevice
where
x y
are the PageSize in points.
Tray selected with tray operators
= Supported
X = Not supported
Printer models
Operator
Tray selected (corresponding image
size is set)
E260, E260d/dn, E360d/dn,
E460dn/dw
X203n MFP, X204n MFP
a3tray
tray with A3-size paper
X
X
a4tray
tray with A4-size paper
a5tray
tray with A5-size paper
b4tray
tray with B4-size paper
X
X
b5tray
tray with B5-size paper
PostScript (PS) emulation
13