Mackie 24.8Bus Meter Bridge

Mackie 24.8Bus Manual

Get Mackie 24.8Bus PDF manuals and user guides View all Mackie 24.8Bus manuals
Add to My Manuals
Save this manual to your list of manuals

Mackie 24.8Bus manual content summary:

  • Mackie 24.8Bus | Meter Bridge - Page 1
    is because our art department wanted something to do on a rainy day1. INSTALLATION INSTRUCTIONS 1. Locate the warranty card and fill it out. If you bought your Meter Bridge at the same time you purchased an 8•Bus series console, you don't need to answer all the questions on the card that came
  • Mackie 24.8Bus | Meter Bridge - Page 2
    MB•16 Meter Bridge MB•E Meter Bridge MB•24 Meter Bridge E MB•32 Meter Bridge with the console's mounting holes. 7. Hand-insert one collar piece into each side, with the "teeth" pointing out (C). Occasionally, the end caps of the Console will try C pin down to interfere with this step. Don't get
  • Mackie 24.8Bus | Meter Bridge - Page 3
    sixth or seventh channel. 6. Assign the last channel you tested to the L/R MIX. Turn up the L/R MIX fader. Engage the L/R switch in the MONITOR section of the Console. 7. Confirm meter activity on both the Meter Bridge VU meters and the console's L/R MAIN LED meters. Pan the channel left and right
  • Mackie 24.8Bus | Meter Bridge - Page 4
    or Mackie Designs Tech Support immediately. METER BRIDGE OPERATION Your meter bridge's ballistics and general behavior is the same as the submaster LED ladders on the Master section of the Console. For the excruciating details, read the section on METERING on page 11 of your 8•Bus manual. When
  • 1
  • 2
  • 3
  • 4
4.
Locate and
identify the hard-
ware that came with
your Meter Bridge:
■
a.
Two (2) slotted screws;
■
■
b.
Two (2) collar pieces (Note
that there is a small
pin protruding from
the bottom of each
collar piece);
■
c.
Two (2) Allen head screws;
■
d.
Two (2) lockwashers;
■
e.
One (1) allen wrench.
5.
Remove the plastic caps that cover
the Meter Bridge mounting holes
on each side of the Console (Draw-
ing A). Feed them to your boa.
6.
Align the Meter Bridge
with the Console (B) and lower it
into place. Tilt the Meter Bridge
back until it is
at rest against
the Console
chassis (or
your tangle of
patchcords).
Make sure
that the meter
bridge's
mounting
holes line up
MB•16
MB•24
MB•32
MB•E
A
Congratulations on adding a Meter
Bridge to your Mackie Designs 8•Bus
Console. Installation is very straightfor-
ward and should take just a few minutes.
The only reason we've included so many
step-by-step drawings is because our art
department wanted something to do on
a rainy day
1
.
INSTALLATION INSTRUCTIONS
1.
Locate the warranty card and fill it
out. If you bought your Meter
Bridge at the same time you pur-
chased an 8•Bus series console, you
don't need to answer all the ques-
tions on the card that came with the
Meter Bridge. Just fill in the model
number of the Meter Bridge, serial
number, purchase date and dealer,
and your name and address.
2.
Make sure that your 8•Bus Console
power supply is turned off.
3.
Remove the Meter Bridge from its
plastic bag. Save the bag. It's handy
for wrapping boa constrictors or
moray eels before popping them in
your freezer.
Also, save the box.
B
MB•32/MB•24/MB•16/MB•E
8•BUS METER BRIDGES
1
And, since every day except four or five in August are
rainy up here in the Northwest Rainforest, they had time
to do quite a nice job.
.