Mackie 32.8Bus Owner's Manual - Page 11

L For example, when you want a super "wet" sound(mostly reverb), the extra gain allows you to bring the channel fader part way down (and the AUX send way up) so the sound is mostly reverb with just a touch of "dry" signal. Don't worry about having mono effects sends: almost all effects units, mono or stereo, have mono inputs. Even if there are two jacks labeled Left and Right, they are almost always combined into mono internally. In the rare cases when an effect actually has true stereo inputs, it is often more convenient to ignore that and treat it as mono anyway. If you really need to send in stereo, just use two AUX sends from the console. Route AUX 1, for example, to the left input and AUX 2 to the right. Then adjust the stereo perspective by favoring one or the other send. For instance, if you have a stereo synth into channels 23 and 24, use AUX 1 on channel 23 and AUX 2 on channel 24. Note: In PRE mode, all AUX SENDS are connected pre-fader but post-EQ. This is usually the most useful setup, but if you prefer, all AUX SENDS can be modified to be pre-EQ, pre-fader. Instructions for this modification can be found on our website at www.mackie.com (click on Support). Or you can call Tech Support at 1-800-258-6883 for assistance. AUX 1 & 2 Auxiliary sends 1 & 2 (24) have two independent level controls and share a common PRE/POST switch. When in the normal post mode, sends 1 & 2 get their signal after the channel fader and the MUTE switch. This is the usual configuration for an effects send, since the level of the effect should follow the volume adjustments made by the channel fader. PRE (1&2) With the PRE switch (25) depressed, AUX SENDS 1 & 2 receive their input from a point before the channel fader and MUTE switch, and are not affected by changes in these controls. This is the normal switch setting for creating stage monitor and/or studio cue headphone sends. AUX 3, 4, 5, 6 Auxiliary sends 3, 4, 5, and 6 (26) are very similar to sends 1 & 2. The differences are in the SHIFT and SOURCE switches. Read on. SHIFT The SHIFT button (27) connects the two level controls, as a pair, to either sends 3 & 4 (in the up position) or to sends 5 & 6 (in the down position). Twice the sends in half the space. SOURCE The SOURCE switch (28) breaks AUX Sends 3-6 away from the main channel strip world that sends 1 & 2 are stuck in, and allows the sends to tap from another source: the MIX-B signal for that channel. This is a very handy thing, whatever you happen to be using MIX-B for. If MIX-B is an additional input for your mixdown, then (when the SOURCE switch is depressed) AUX Sends 3-6 are effects sends connected to that source. If MIX-B is your studio monitor submix from the recorder, then AUX Sends 3-6 are a great source of headphone cue signals. They will follow playback, record and punch-ins automatically as your recorder does its stuff. PRE (3-6) The PRE switch (29) for Sends 3-4-5-6 functions just like the PRE switch sends 1 & 2, when the AUX SOURCE switch is in the CHANNEL (up) position. Additionally, the PREswitch will tap the prelevel (and pre-mute) signal of whichever SOURCE you have selected-channel or MIX B. +4 10dB -40dBV MIC/LINE 50dB TAPE TRIM GAIN FLIP U 1 +15 2U OO OO OO OO +15 AUX PRE 3U 5 +15 4U 6 +15 AUX SHIFT 24 PRE CHANNEL MIX-B SOURCE TIVITY 9