Mackie SR244 VLZ Pro / SR324 VLZ Pro VLZ Pro Owner's Manual - Page 22
Master Features, Lamp Connector, Aux Send Master, Aux Send Masters, Solo
View all Mackie SR244 VLZ Pro / SR324 VLZ Pro manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 22 highlights
MASTER SECTION FEATURES LAMP OO OO OO OO OO OO U 1 +15 U 2 +15 U 3 +15 U 4 +15 U 5 +15 U 6 +15 AUX SEND MASTERS TRACK 1 • 5 5 SOLO SOLO SOLO SOLO SOLO SOLO TRACK 2 • 6 5 OO OO OO OO U U 1 +20 U 1 +15 U OO OO OO +20 U +20 U 2 2 +15 TO AUX 3 SEND 1-2 (EFX TO MONITOR) U 4 +20 +20 TAPE RETURN ASSIGN TO SUB 1-2 3-4 SUB STEREO AUX RETURNS GLOBAL AUX RETURN SOLO TRACK 3 • 7 5 TRACK 4 • 8 5 CLIP 28 10 7 4 2 0 2 4 7 10 20 30 40 LEVEL SET LEFT RIGHT OPERATING LEVEL 0dB = 0dBu RUDE SOLO LIGHT U POWER MODE +15 LEVEL SOLO PRE FADER IN PLACE AFL AUX SUB OO OO 0 +10 AIR 16kHz SOLO 0 +10 AIR 16kHz SOLO 0 +10 AIR 16kHz SOLO 0 +10 AIR 16kHz SOLO MAX LEVEL MAIN MIX TALKBACK AUX 1-2 L R PAN L/R ASSIGN SUB 1 dB 10 5 U 5 10 20 30 40 50 60 L R PAN L/R ASSIGN SUB 2 dB 10 5 U 5 10 20 30 40 50 60 L R PAN L/R ASSIGN SUB 3 dB 10 5 U 5 10 20 30 40 50 60 L R PAN L/R ASSIGN SUB 4 dB 10 5 U 5 10 20 30 40 50 60 TAPE RETURN TO PHONES / C R OO MAX PHONES / C-R LEVEL MAIN MIX TAPE RETURN TO MAIN MIX LEFT/RIGHT dB 10 5 U 5 10 20 30 40 50 60 In the master section, signals leaving the channel strips are mixed, manipulated and sent to the outputs in the patchbay. Additionally, there are four more stereo inputs here, used to add effects to the main mix or other destinations. 45. LAMP This female BNC connector provides 12 volts on its center pin. Connect any quality gooseneck lamp here. AUX SEND MASTER: (46 and 47) 46. AUX SEND MASTERS Aux send signals originate at each channel's AUX (26) knobs, are mixed together, sent through these controls, and exit at the patchbay's AUX SENDS (10). Turned fully up, these controls provide 15 dB of additional gain, the center "U" label is unity gain and fully down is off. When an aux send is used for monitors, these knobs can be used to raise or lower individual monitor mixes to suit the performer's taste. For recording work, these knobs are typically set near unity and left alone; most adjustments are made per channel. 47. SOLO Engaging any of these switches will isolate the associated signal and send it to the control room, phones and meters. See RUDE SOLO LIGHT (61) and MODE (63) for more information. OO OO OO OO OO 22