Magnavox ZV457MG9 User manual, English (US) - Page 30

SETTING THE CLOCK, Auto Clock Setting

Get Magnavox ZV457MG9 - DVDr/ VCR Combo PDF manuals and user guides
UPC - 053818570746
View all Magnavox ZV457MG9 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

SETTING THE CLOCK Auto Clock Setting This unit can set the time and date automatically by referring to a channel that carries clock information. If a PBS (public broadcasting station) channel is available on Cable in your area, follow "Auto Clock Setting" below. If not, follow "Manual Clock Setting" on page 32. Make sure • The cable TV connections are correct. • Channels are set. (Refer to page 28.) ANALOG AUTO CLOCK SETTING (Cable TV only) 1 Press [SETUP] and use [K / L] to select "General Setting", then press [OK]. "General Setting" menu will appear. 2 Use [K / L] to select "Clock", then press [OK]. "Clock" menu will appear. 3 Use [K / L] to select "Auto Clock Setting", then press [OK]. 4 Use [K / L] to select "Auto", then press [OK]. Auto Clock Setting OFF Auto Manual Note • The clock may set itself automatically after you connect the antenna/cable signal and plug in the power cord. • Only the Analog PBS channel Cable TV signal is effective for auto clock setting. • For analog auto clock setting, incorrect time may be obtained depending on the broadcast information. If this occurs, set the "Auto Clock Setting" to "OFF" at step 4 above and try "Manual Clock Setting" on page 32. 30 EN 5 Press [SETUP] to exit. 6 Press [STANDBY-ON y] to turn the unit to the standby mode. This unit will search for the time only when the power is in the standby mode. Initially leave it in standby mode for at least 15 minutes to give this unit time to set the clock. Once the clock is set, the unit receives the clock data at 12:00 am & 12:00 pm when unit is in standby mode. Check the time after the Auto Clock was set, if it is incorrect time then set the "Auto Clock Setting" to "OFF" in step 4 above. Then try "Manual Clock Setting" on page 32. Manual Auto Clock Setting If the unit chooses an incorrect PBS channel on Cable TV, set the PBS channel manually by following the steps below. 1 Select "Manual" at step 4 above, then press [OK]. 2 Use [the Number buttons] or [K / L] to enter your Cable TV Analog PBS channel number, then press [OK]. Set Channel No. CH 1 3 Press [SETUP] to exit and turn the unit to the standby mode.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
30
EN
30
EN
SETTING THE CLOCK
Note
• The clock may set itself automatically after you
connect the antenna/cable signal and plug in the
power cord.
• Only the Analog PBS channel Cable TV signal is
effective for auto clock setting.
• For analog auto clock setting, incorrect time may be
obtained depending on the broadcast information. If
this occurs, set the “Auto Clock Setting” to “OFF” at
step 4 above and try “Manual Clock Setting” on page
32.
Auto Clock Setting
This unit can set the time and date automatically by
referring to a channel that carries clock information. If a
PBS (public broadcasting station) channel is available on
Cable in your area, follow “Auto Clock Setting” below. If
not, follow “Manual Clock Setting” on page 32.
Make sure
•
The cable TV connections are correct.
•
Channels are set. (Refer to page 28.)
ANALOG AUTO CLOCK SETTING (Cable TV only)
1
Press [SETUP] and use [
K
/
L
] to
select “General Setting”, then press
[OK].
“General Setting” menu will appear.
2
Use [
K
/
L
] to select “Clock”, then
press [OK].
“Clock” menu will appear.
3
Use [
K
/
L
] to select “Auto Clock
Setting”, then press [OK].
4
Use [
K
/
L
] to select “Auto”, then
press [OK].
Auto Clock Setting
OFF
Auto
Manual
5
Press [SETUP] to exit.
6
Press [STANDBY-ON
y
] to turn the
unit to the standby mode.
This unit will search for the time only when the
power is in the standby mode. Initially leave it in
standby mode for at least 15 minutes to give this
unit time to set the clock. Once the clock is set, the
unit receives the clock data at 12:00 am & 12:00 pm
when unit is in standby mode. Check the time after
the Auto Clock was set, if it is incorrect time then set
the “Auto Clock Setting“ to “OFF” in step 4 above.
Then try “Manual Clock Setting“ on page 32.
Manual Auto Clock Setting
If the unit chooses an incorrect PBS channel on Cable
TV, set the PBS channel manually by following the steps
below.
1
Select “Manual” at step 4 above, then
press [OK].
2
Use [the Number buttons] or [
K
/
L
]
to enter your Cable TV Analog PBS
channel number, then press [OK].
Set Channel No.
CH
1
3
Press [SETUP] to exit and turn the
unit to the standby mode.