Magnavox ZV457MG9 User manual, English (US) - Page 45

Introduction Connections Basic Setup TIMER RECORDING How to select a channel number for the timer recording Analog TV For channel number 2-6 press, press [B] or [ • ] to decide the channels. For other channels (7-69), the channel will be decided as soon as you enter the channel number. Analog CATV For channel number 1-12 press, press [B] or [ • ] to decide the channels. For other channels (13125), the channel will be decided as soon as you enter the channel number. Digital TV For channel number 1-9 press, press [B] or [ • ] to decide the channels. For other channels (10-99), the channel will be decided as soon as you enter the channel number. Digital CATV For channel number 1-13 press, press [B] or [ • ] to decide the channels. For other channels (14135), the channel will be decided as soon as you enter the channel number. minor channels For channel number 1-9 press, press [B] or [ • ] to decide the channels. For other channels (10-99), the channel will be decided as soon as you enter the channel number. • You can decide the 1-digit channel number by pressing 0 first , then enter desired 1-digit channel number. e.g.) "5": [0]+[5] • For selecting the channels with [K / L] you need to press [B] or [ • ] to decide the channel number. • For selecting the minor channels with [K / L], please make sure the minor channel your are selecting is existed. [K / L] does not skip the non-existed minor channels. Recording Playback Editing Function Setup VCR Functions To stop the timer recording in progress 1) Press [STOP C ] on the remote control. 2) Confirmation message will appear. Select "Yes", then press [OK]. • To stop the timer recording immediately, press [ CSTOP] on the unit. Checking, canceling, or correcting the timer programming information If the timer program did not complete correctly, the error number appears in the timer programming list. Timer Programming FRI JAN/02 11:00AM Date Start End CH E41 JAN/02 12:00AM 1:00AM DTV69. 1 New Program 1) Press [TIMER SET]. 2) Press [TIMER]. 3) Check the information. Timer Programming JAN/ 2/09 12:00 AM 69.1 SP SP (1:00) THU JAN/01 11:00AM Date JAN/02 Start End 12:00AM 1:00AM New Program CH DTV69. 1 4-A) To delete the timer program: 1 Use [K / L] to select the program you want to delete, then press [OK]. 2 Use [K / L] to select "Delete", then press [OK]. Confirmation window will appear. 3 Use [K / L] to select "Yes", then press [OK]. 4-B) To correct the timer program: 1 Use [K / L] to select the program you want to correct, then press [OK]. 2 Use [K / L] to select "Program Change", then press [OK]. 3 Correct the timer program by using [K / L / { / B], then press [OK]. 5) Press [TIMER] to exit. 6) Press [TIMER SET] to return to the timer standby mode. Note • Press [TIMER] to check the timer recording in progress. When the timer recording is proceeding, that program will be highlighted with red. In this case, you cannot select any other program. 1/1 Each error number means: E1-22 Recording error other E41 E37-39 than below E24 Unrecordable disc E42 E25-26 Copy prohibited E43 program E29 Disc protected E44 E30 Disc full E45 E35 PCA full *1 E46 E36 Already finalized video format disc E40 Some portion has not been recorded because of program overlapping. Recording did not start at the start time. Power failed No disc when recording Already 49 titles recorded Already 254 chapters recorded Copy prohibited program It is impossible to record additionally on a disc recorded by other units when setting " Make Recording Compatible" to "OFF". • E23, E27, E28, E31, E32, E33 and E34 are not displayed. • A program with the error number is grayed in the timer programming list. • Timer program with an error number will be cleared once the entry screen for the program is displayed. *1 PCA is a disc's space reserved for recording test. Others Español EN 45