Makita AN611 Owners Manual - Page 13

Adjusting depth, nailing, Connecting air hose, Operation - nailer

Get Makita AN611 PDF manuals and user guides View all Makita AN611 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Place the nail coil over the coil support plate. Uncoil enough nails to reach the feed claw. Place the first nail in the driver channel and the second nail in the feed claw. The nail heads must be in the slot in the feeder body. Place other uncoiled nails on feeder body. Close the magazine cap and door after checking to see that the nail coil is set properly in the magazine. Adjusting depth of nailing I CAUTION: Always lock the trigger and disconnect the hose before adjusting the depth of nailing. To adjust the depth of nailing, turn the adjuster so that the arrow above the adjuster will point to the number indicated on the adjuster. The depth of nailing is the deepest when the arrow points to the number 1. It will become shallower as the arrow points to higher number. The depth can be changed in approx. 1.0 mm (1/32") increments per graduation. If nails cannot be driven deep enough even when the arrow points to the number 1, increase the air pressure. If nails are driven too deep even when the arrow points to the number 9, decrease the air pressure. Generally speaking, the tool service life will be longer when the tool is used with ./ lower air pressure and the adjuster set to a lower number. Adjuster Connecting air hose Lock the trigger. Slip the air socket of the air hose onto the I air fitting on the nailer. Be sure that the air socket locks firmly into position when installed onto the air fitting. A hose coupling must be installedon or near the tool in such a way that the pressure reservoir will discharge at the time the air supply coupling is disconnected. Air fitting Operation 1) To drive a nail, you may place the contact element against the workpiece and pull the trigger, or 2) Pull the trigger first and then place the contact element against the workpiece. No. 1 method is for intermittent nailing, when you wish to drive a nail carefully and very accurately. No. 2 method is for continuous nailina

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
Place the nail coil over the coil support plate. Uncoil enough
nails
to
reach the feed claw. Place the first nail in the driver
channel and the second nail in the feed claw. The nail heads
must be in the
slot
in the feeder body. Place other uncoiled
nails on feeder body. Close the magazine cap and door after
checking to see that the nail coil is set properly in the
mag
azine.
Adjusting depth
of
nailing
CAUTION:
Always lock the trigger and disconnect the hose before adjusting the depth of nailing.
I
To adjust the depth of nailing, turn the adjuster
so
that the
arrow above the adjuster will point
to
the number indicated
on the adjuster. The depth of nailing is the deepest when
the arrow points
to
the number
1.
It will become shallower
as the arrow points
to
higher number. The depth can be
changed in approx.
1.0
mm (1/32”) increments per gradua-
tion.
If
nails cannot be driven deep enough even when the
arrow points
to
the number
1,
increase the air pressure.
If
nails are driven
too
deep even when the arrow points
to
the
number
9,
decrease the air pressure. Generally speaking,
the
tool
service life will be longer when the
tool
is used with
lower air pressure and the adjuster set
to
a lower number.
Connecting air hose
Lock the trigger. Slip the air socket of the air hose onto the
air fitting on the nailer. Be sure that the air socket locks firmly
into position when installed onto the air fitting. A hose
coupling must be installed on or near the
tool
in such a way
that the pressure reservoir will discharge at the time the air
supply coupling is disconnected.
./
Adjuster
I
Air
fitting
Operation
1)
To drive a nail, you may place the contact element against the workpiece and pull the trigger, or
2)
Pull the trigger first and then place the contact element against the workpiece.
No.
1
method is for intermittent nailing, when you wish
to
drive a nail carefully and very accurately.
No.
2
method is for continuous nailina