Makita GA5040X1 Makita GA5040X1 Instruction Manual - Page 6

Save These Instructions., Symbols

Get Makita GA5040X1 PDF manuals and user guides View all Makita GA5040X1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

22. Use the specified surface of the wheel to perform the grinding. 23. Watch out for flying sparks. Hold the tool so that sparks fly away from you and other persons or flammable materials. 24. Do not leave the tool running. Operate the tool only when hand-held. 25. Do not touch the workpiece immediately after operation; it may be extremely hot and could burn your skin. 26. Always be sure that the tool is switched off and unplugged or that the battery cartridge is removed before carrying out any work on the tool. 27. Observe the instructions of the manufacturer for correct mounting and use of wheels. Handle and store wheels with care. 28. Do not use separate reducing bushings or adaptors to adapt large hole abrasive wheels. 29. Use only flanges specified for this tool. 30. For tools intended to be fitted with threaded hole wheel, ensure that the thread in the wheel is long enough to accept the spindle length. 31. Check that the workpiece is properly supported. 32. Pay attention that the wheel continues to rotate after the tool is switched off. 33. If working place is extremely hot and humid, or badly polluted by conductive dust, use a short-circuit breaker (30 mA) to assure operator safety. 34. Do not use the tool on any materials containing asbestos. 35. Do not use water or grinding lubricant. 36. Ensure that ventilation openings are kept clear when working in dusty conditions. If it should become necessary to clear dust, first disconnect the tool from the mains supply ( use non metallic objects ) and avoid damaging internal parts. 37. When use cut-off wheel, always work with the dust collecting wheel guard required by domestic regulation. 38. Cutting discs must not be subjected to any lateral pressure. SAVE THESE INSTRUCTIONS. WARNING: DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to safety rules for the subject product. MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. USD201-2 Symbols The followings show the symbols used for tool. ･ volts ･ amperes ･ hertz ･ alternating current ･ no load speed ･ Class II Construction ･ revolutions or reciprocation per minute 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
6
22.
Use the specified surface of the wheel to
perform the grinding.
23.
Watch out for flying sparks. Hold the tool so
that sparks fly away from you and other
persons or flammable materials.
24.
Do not leave the tool running. Operate the tool
only when hand-held.
25.
Do not touch the workpiece immediately after
operation; it may be extremely hot and could
burn your skin.
26.
Always be sure that the tool is switched off
and unplugged or that the battery cartridge is
removed before carrying out any work on the
tool.
27.
Observe the instructions of the manufacturer
for correct mounting and use of wheels.
Handle and store wheels with care.
28.
Do not use separate reducing bushings or
adaptors to adapt large hole abrasive wheels.
29.
Use only flanges specified for this tool.
30.
For tools intended to be fitted with threaded
hole wheel, ensure that the thread in the wheel
is long enough to accept the spindle length.
31.
Check
that
the
workpiece
is
properly
supported.
32.
Pay attention that the wheel continues to
rotate after the tool is switched off.
33.
If working place is extremely hot and humid,
or badly polluted by conductive dust, use a
short-circuit
breaker
(30
mA)
to
assure
operator safety.
34.
Do not use the tool on any materials
containing asbestos.
35.
Do not use water or grinding lubricant.
36.
Ensure that ventilation openings are kept clear
when working in dusty conditions. If it should
become
necessary
to
clear
dust,
first
disconnect the tool from the mains supply
( use non metallic objects ) and avoid
damaging internal parts.
37.
When use cut-off wheel, always work with the
dust collecting wheel guard required by
domestic regulation.
38.
Cutting discs must not be subjected to any
lateral pressure.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this
instruction manual may cause serious personal
injury.
USD201-2
Symbols
The followings show the symbols used for tool.
･
volts
･
amperes
･
hertz
･
alternating current
･
no load speed
･
Class II Construction
･
revolutions or reciprocation per minute