Marantz NR1601 NR1601 User Manual - English - Page 78

ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Resetting the microprocessor Perform this procedure if the display is abnormal or if operations cannot be performed. When the microprocessor is reset, all the settings are reset to their default values. Various setting details can be saved and reset on this device. If setting details are saved before returning to the default values, after returning to the default settings, setting details can be returned to the same values as before returning to the defaults. To return all of the settings to the default values, perform steps 2 to 4 without performing step 1. ON/STANDBY ENTER STATUS RETURN 1 When the power is ON, press and hold STATUS and ENTER for more than 3 seconds. After "MEMORY SAVING" is shown on the display, "COMPLETE"is shown to inform you that the settings have been saved. 2 Turn off the power using ON/STANDBY. 3 Press ON/STANDBY while simultaneously pressing ENTER and RETURN. 4 Once the display starts flashing at intervals of about 1 second, release the two buttons. 5 Press and hold STATUS and ENTER for more than 3 seconds. After "MEMORY LOAD" is shown on the display, "COMPLETE" is shown to inform you that the settings have returned to those saved in step 1. If in step 4 the display does not flash at intervals of about 1 second, start over from step 2. Specifications nn Audio section • Power amplifier Rated output: Output connectors: • Analog Input sensitivity/Input impedance: Frequency response: S/N: nn Video section • Standard video connectors Input/output level and impedance: Frequency response: • Color component video connector Input/output level and impedance: Frequency response: nn Tuner section Receiving Range: Usable Sensitivity: 50 dB Quieting Sensitivity: S/N (IHF-A): Total harmonic Distortion (at 1 kHz): nn General Power supply: Power consumption: Maximum external dimensions: Weight: nn Remote control unit (RC010SR) Batteries: Front: 50 W + 50 W (8 Ω, 20 Hz - 20 kHz with 0.08 % T.H.D.) 75 W + 75 W (6 Ω, 1 kHz with 10 % T.H.D.) Center: 50 W (8 Ω, 20 Hz - 20 kHz with 0.08 % T.H.D.) 75 W (6 Ω, 1 kHz with 10 % T.H.D.) Surround: 50 W + 50 W (8 Ω, 20 Hz - 20 kHz with 0.08 % T.H.D.) 75 W + 75 W (6 Ω, 1 kHz with 10 % T.H.D.) Surround Back: 50 W + 50 W (8 Ω, 20 Hz - 20 kHz with 0.08 % T.H.D.) 75 W + 75 W (6 Ω, 1 kHz with 10 % T.H.D.) 6 - 8 Ω 130 mV/50 kΩ 10 Hz - 100 kHz - ±3 dB (Source Direct mode) 98 dB (IHF-A weighted, Source Direct mode) 1 Vp-p, 75 Ω 5 Hz - 10 MHz - +1, -3 dB Y (brightness) signal - 1 Vp-p, 75 Ω PB / CB signal - 0.7 Vp-p, 75 Ω PR / CR signal - 0.7 Vp-p, 75 Ω 5 Hz - 60 MHz - +0, -3 dB [FM] (Note: μV at 75 Ω, 0 dBf = 1 x 10-15 W) 87.5 MHz - 107.9 MHz 1.2 μV (12.8 dBf) MONO 2.8 μV (20.2 dBf) MONO 70 dB STEREO 67 dB MONO 0.7 % STEREO 1.0 % AC 120 V, 60 Hz 250 W 0.2 W (Standby) 3 W (CEC standby) 440 (W) x 105 (H) x 367 (D) mm 9.0 kg R03/AAA Type (two batteries) [AM] 520 kHz - 1710 kHz 18 μV For purposes of improvement, specifications and design are subject to change without notice. 74