Marantz RC1200 User Guide - Page 13

If FULL is displayed on the LCD, Jog Dial, Function, TV, VCR, etc.

Get Marantz RC1200 PDF manuals and user guides View all Marantz RC1200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

ENGLISH • In the rare event that NG appears on the LCD, it means that the remote controller you are attempting to learn from uses special signals that cannot be learned by the Marantz remote controller. 6. Follow the same procedure to make the remote controller learn the ten-key ⁄7 operation used by the laser disc player's remote controller. 7. Repeat the procedure from step 3 to have the remote controller learn the signal codes for the other components such as TV, VCR, etc. • If no buttons are pressed for approximately 1 minute while in the LEARN mode, the remote controller automatically returns to the USE mode. • When programming the function buttons, first switch to the desired function, then press the button again. 8. When you have finished programming the remote controller, use a ballpoint pen or other sharp point to once again press the MODE button z to return it to the USE mode. The LCD displays the USE indicator, and the newly programmed codes now can be used. If FULL is displayed on the LCD If FULL is displayed on the LCD B when programming in the LEARN mode, it means that the memory has become too full to hold any further codes. If FULL is displayed no matter how many times you attempt to enter new codes, it means that the remote controller cannot accept any new codes until some of the previously learned codes are deleted to make space in the memory. Select unneeded codes for each of the Jog Dial control m and Function buttons ,, which show FULL and delete them from the memory. 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
12
ENGLISH
•
In the rare event that
NG
appears on
the LCD, it means that the remote
controller you are attempting to learn
from uses special signals that cannot
be learned by the Marantz remote
controller.
6.
Follow the same procedure to make the
remote controller learn the ten-key
⁄7
operation used by the laser disc player’s
remote controller.
7.
Repeat the procedure from step 3 to have
the remote controller learn the signal
codes for the other components such as
TV, VCR, etc.
• If no buttons are pressed for
approximately 1 minute while in the
LEARN mode, the remote controller
automatically returns to the USE mode.
• When programming the function
buttons, first switch to the desired
function, then press the button again.
8.
When you have finished programming the
remote controller, use a ballpoint pen or
other sharp point to once again press the
MODE
button
z
to return it to the USE
mode. The LCD displays the
USE
indicator, and the newly programmed
codes now can be used.
If FULL is displayed on the LCD
If
FULL
is displayed on the LCD
B
when
programming in the LEARN mode, it means
that the memory has become too full to hold
any further codes.
If
FULL
is displayed no matter how many
times you attempt to enter new codes, it
means that the remote controller cannot
accept any new codes until some of the
previously learned codes are deleted to make
space in the memory. Select unneeded codes
for each of the
Jog Dial
control
m
and
Function
buttons
,
, which show
FULL
and
delete them from the memory.