Marantz RC1200 User Guide - Page 17

Erasing Programmed Codes, Jog Dial, Returning to Factory Presets, LEARN - rc 1200

Get Marantz RC1200 PDF manuals and user guides View all Marantz RC1200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

ENGLISH 7. Follow the same procedure to enter "DA". When finished, press the OK Cursor button ⁄0. Pressing OK permanently fixes the newly written characters. Similarly, the function names can be overwritten by pressing the function buttons. • Up to 5 characters can be entered in the function display and command display. • To rewrite the names of the other items in the Command Name indicator, use the Jog Dial m to select the desired command and repeat from step 5. 8. When you are finished rewriting, use a ballpoint pen or other sharp point to press the MODE button z to return the remote controller to the USE mode. The USE indicator is displayed on the LCD, and the newly programmed codes now can be used. POWER SOURCE ON ON / OFF OFF LEARNING REMOTE CONTROL RC 1200 MACRO MODE ERASING PROGRAMMED CODES (Returning to Factory Presets) Codes that have been programmed into the memory can be erased in 4 ways: by button(s), by function(s), by Jog Dial command, and by erasing all memory contents. 1. Use a ballpoint pen or other sharp point to press the MODE button z to switch the remote controller to the LEARN mode, so that the LEARN indicator is blinking on the LCD. Note: Erasing of programmed codes is only possible in the LEARN mode. 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
16
ENGLISH
ON
OFF
ON / OFF
SOURCE
MACRO
MODE
LEARNING
REMOTE
CONTROL
RC
1200
POWER
7.
Follow the same procedure to enter “D-
A”. When finished, press the
OK
Cursor
button
⁄
0
. Pressing
OK
permanently fixes
the newly written characters.
Similarly, the function names can be
overwritten by pressing the function buttons.
•
Up to 5 characters can be entered in the
function display and command display.
•
To rewrite the names of the other items
in the Command Name indicator, use
the
Jog Dial
m
to select the desired
command and repeat from step 5.
8.
When you are finished rewriting, use a
ballpoint pen or other sharp point to press the
MODE
button
z
to return the remote
controller to the USE mode.
The
USE
indicator is displayed on the LCD, and the
newly programmed codes now can be used.
ERASING PROGRAMMED CODES
(Returning to Factory Presets)
Codes that have been programmed into the
memory can be erased in 4 ways: by
button(s), by function(s), by Jog Dial
command, and by erasing all memory
contents.
1.
Use a ballpoint pen or other sharp point to
press the
MODE
button
z
to switch the
remote controller to the LEARN mode, so
that the
LEARN
indicator is blinking on
the LCD.
Note:
Erasing of programmed codes is only
possible in the LEARN mode.