Marantz SR-880mkII User Guid - Page 10
button., NIGHT, Switch, enable, disable, LEVEL, Select, output, level, signal, include, Dolby,
View all Marantz SR-880mkII manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 10 highlights
OSD MAIN MENU I> INPUT SELECTOR SURROUND MODE I> TEST TONE MULTI ROOMSEL:OFF SLEEP TIMER: OFF SET UP MENU ....MENU OFF I> TEST TONE : ON FL C FR f> FRONT L + 6 dB SL SR \ ,...RETURN TO MAINMENU } ( .1, SURROUND MODE C> MODE : DOLBY CENTER DELAY : 0 mS SURROUND DELAY : 20 mS RE-EQ : OFF NIGHT MODE : OFF LFE LEVEL : 0dB RETURN TO MAIN MENU ) 7. Press cursor button A or V to move the cursor to "TEST TONE" and press the OK button. • You can use the cursor button 4 or l• to move to the "TEST TONE MENU". 8. Press the OK button to turn on the TEST TONE. Note that a test signal noise will be heard from the FRONT LEFT CH speakers. Adjust the test signal noise output to the appropriate level by using the master volume control, 9. Press the CH.SEL (CH+, channel select button ), each press changes the speaker channel generating the test tone in the following order: C CENTER - -- ,-RIGHT " SURROUND L.4`-" SURROUND R After each press of the CH.SEL (CH+) button D6 on page 3 at AMP mode, adjust the level by using the CH.LEVEL A and V buttons D7, D8 on page 3 at AMP mode or cursor t and 0. buttons until the sound level from each speaker appears equal. Note: When either the CENTER CH or SURROUND CH SET UP set to NONE the test tone skips each channel. The test tone is not output to the subwoofer irrespective of ON or OFF selection. 10. When the balance between the volume levels of different speakers has been adjusted, stop the test tone generation by pressing the cursor button • and 44 or lb. so that the cursor is set to other menu. The volume levels of the speaker channels set above will be used in common for the AUTO, DOLBY and DTS surround modes. 11. Delay Time Setting O On the MAIN MENU, move the arrow-shaped cursor to "SURROUND MODE" and press the OK button. C) Press cursor button V to move the cursor to center or surround channel. ® Select the desired delay time with cursor buttons 4 and IP% O Press the OK button or cursor button V or A to complete the setting. Normally use 5 ms. Use 10 or 15 ms if you are much closer to the rear speakers than the front speakers. In the DOLBY and DTS mode, the delay time is variable in the following sequence. r- SURROUND CH. 5 -0 .10 15 CENTER CH. r -4 5 0 For more information about setting the delay time, please turn to Page 35. Notes: Once the delay time is set, it is stored automatically as a common setting with DOLBY and DTS. Unless it is set again, the same delay setting will be applied every time DOLBY and DTS is selected. Once this procedure for the set-up and calibration has been done, there should be no need to repeat it in daily use. A monthly check of channel levels is recommended: simply press the TEST button, followed by repeated pressing of the CH.SEL button to verify that all channels are operational and at the same level, Once done press the TEST button again to end the test. 12. RE-EQ Switch the cinema RE-EQ to enable (ON) or disable (OFF) with 4 or ► button. 13. NIGHT MODE Switch the NIGHT MODE to enable (ON) or disable (OFF) with 44 or P. button. 14. LFE LEVEL Select the output level of the LFE signal include in the Dolby Digital or DTS signal: The-level-is ordinarily-set-to 0 dB-The-level-is selectable 0 dB, -10