Maytag MGR7662WB Installation Guide - Page 15

To Convert Oven Broil Burner Natural Gas to LP Gas

Get Maytag MGR7662WB - 30inch Ing Gas Range PDF manuals and user guides
UPC - 883049176468
View all Maytag MGR7662WB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

6. Slide the front of the bake burner to the side to remove tab from front of oven. Lift the back of the bake burner off the oven orifice, disconnect the igniter wire, and set the bake burner aside on a covered surface. B To Convert Oven Broil Burner (Natural Gas to LP Gas) 1. Remove the screw from the broil burner. 2. Remove the broil burner from the broil burner orifice hood. NOTE: The broil burner will hang in the back of the oven while changing the orifice hood. A B A A. Screws B. Bake burner 7. Use a ³⁄₈" nut driver or combination wrench and turn the Natural gas bake burner orifice spud counterclockwise to remove. The spud will be stamped with a "47" or "49." 8. Replace the "47" spud with a "56" spud or replace the "49" spud with a "57" spud. Install the LP gas bake burner orifice spud, turning it clockwise until snug. IMPORTANT: Do not overtighten. A C A. Broil burner B. Screws C. Orifice hood 3. Use a ³⁄₈" combination wrench and turn the Natural gas broil burner orifice hood counterclockwise to remove. The hood will be stamped with a "155" or "53." 4. Replace the "155" hood with a "100" hood or replace the "53" hood with a "090" hood. Install the LP gas broiler burner orifice hood, turning it clockwise until snug. IMPORTANT: Do not overtighten. A x.xx A. Orifice spud 9. Connect the igniter wire to the bake burner, position the back of the bake burner over the oven orifice, and slide the tab on front of the bake burner into the front of the oven. 10. Reattach the bake burner with 2 screws. 11. Insert the tabs on the rear of the flame spreader into the rear of the oven. 12. Reattach the front tabs of the flame spreader to the oven with 2 screws. 13. Position the front of the oven bottom panel toward the front frame and lower the rear of the oven bottom panel into the oven. 14. Reattach the oven bottom panel with 2 screws. A. Orifice hood 5. Place the broil burner on the broil burner orifice hood and insert the broil burner ceramic igniter in the hole in the rear of the oven. 6. Position the broil burner against the top of the oven and attach it with 2 screws. 7. Replace storage drawer or warming drawer. See the "Storage Drawer" or "Warming Drawer" section. 8. Replace the oven door if it has been removed. See the "Oven Door" section. 9. Replace the oven racks. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
15
6.
Slide the front of the bake burner to the side to remove tab
from front of oven. Lift the back of the bake burner off the
oven orifice, disconnect the igniter wire, and set the bake
burner aside on a covered surface.
7.
Use a
³⁄₈
" nut driver or combination wrench and turn the
Natural gas bake burner orifice spud counterclockwise to
remove. The spud will be stamped with a “47” or “49.”
8.
Replace the “47” spud with a “56” spud or replace the “49”
spud with a “57” spud. Install the LP gas bake burner orifice
spud, turning it clockwise until snug.
IMPORTANT:
Do not overtighten.
9.
Connect the igniter wire to the bake burner, position the back
of the bake burner over the oven orifice, and slide the tab on
front of the bake burner into the front of the oven.
10.
Reattach the bake burner with 2 screws.
11.
Insert the tabs on the rear of the flame spreader into the rear
of the oven.
12.
Reattach the front tabs of the flame spreader to the oven with
2 screws.
13.
Position the front of the oven bottom panel toward the front
frame and lower the rear of the oven bottom panel into the
oven.
14.
Reattach the oven bottom panel with 2 screws.
To Convert Oven Broil Burner (Natural Gas to LP Gas)
1.
Remove the screw from the broil burner.
2.
Remove the broil burner from the broil burner orifice hood.
NOTE:
The broil burner will hang in the back of the oven while
changing the orifice hood.
3.
Use a
³⁄₈
" combination wrench and turn the Natural gas broil
burner orifice hood counterclockwise to remove. The hood
will be stamped with a “155” or “53.”
4.
Replace the “155” hood with a “100” hood or replace the
“53” hood with a “090” hood. Install the LP gas broiler burner
orifice hood, turning it clockwise until snug.
IMPORTANT:
Do not overtighten.
5.
Place the broil burner on the broil burner orifice hood and
insert the broil burner ceramic igniter in the hole in the rear of
the oven.
6.
Position the broil burner against the top of the oven and
attach it with 2 screws.
7.
Replace storage drawer or warming drawer. See the “Storage
Drawer” or “Warming Drawer” section.
8.
Replace the oven door if it has been removed. See the “Oven
Door” section.
9.
Replace the oven racks.
A. Screws
B. Bake burner
A. Orifice spud
A
B
A
A. Broil burner
B. Screws
C. Orifice hood
A. Orifice hood
B
C
A
x.xx
A