NEC NP-M332XS MP300CM Installation Manual - Page 10

Caution

Get NEC NP-M332XS PDF manuals and user guides View all NEC NP-M332XS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Projector Alignment 9 To adjust yaw (swivel) for wood stud, concrete ceiling, and threaded rod mounting applications: Loosen wood screws (F) if flush mounted to wood joists (page 5) or concrete ceilings (page 6), or loosen locknuts on threaded rods (page 7), until projector mount can be rotated. Rotate mount to desired position and retighten screws or locknuts. To adjust yaw (swivel) for extension column applications: Loosen screw on projector mount assembly (A) indicated below until projector mount can be rotated. Rotate mount to desired position and retighten screw. To adjust pitch (forward and backward tilt): Turn knob on back of mount as shown below. Pull knob out and turn by hand for easy adjustment or insert #2 phillips screwdriver in end of knob and turn. To adjust roll (side to side tilt): Turn knob on side of mount as shown below. Pull knob out and turn by hand for easy adjustment or insert #2 phillips screwdriver in end of knob and turn. ARROW INDICATES FRONT OF MOUNT A KNOB FOR PITCH ADJUSTMENT BACK OF MOUNT SCREW FOR YAW (SWIVEL) STOP (REFER TO STEP 1, INSTALLATION TO EXTENSION COLUMNS, FIG. 1.2) KNOB FOR ROLL ADJUSTMENT 9-1 To prevent tampering with the pitch and roll adjustments: Tighten the two tamper resistant security screws on the projector mount assembly using 4 mm security allen wrench (B) to lock the pitch and roll adjustments as shown below. Note: Tighten screws firmly, but do not overtighten. Overtightening can damage the mount. CAUTION • Do not adjust pitch or roll while tamper resistant security screws are fully engaged. • Loosen the two tamper resistant security screws one complete turn before adjusting the projector mount assembly or damage may occur. TO LOCK PITCH, TIGHTEN TAMPER RESISTANT SECURITY SCREW Visit the Peerless Web Site at www.peerlessmounts.com SIDE VIEW 10 of 10 ISSUED: 10-01-10 SHEET #: 056-9034-4 07-29-11 For customer care call 1-800-865-2112 © 2011, Peerless Industries, Inc. All rights reserved. All other brand and product names are trademarks or registered trademarks of their respective owners.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
ISSUED: 10-01-10
SHEET #: 056-9034-4
07-29-11
Visit the Peerless Web Site at www.peerlessmounts.com
10 of 10
For customer care call 1-800-865-2112
SCREW FOR YAW (SWIVEL) STOP
(REFER TO STEP 1, INSTALLATION
TO EXTENSION COLUMNS, FIG. 1.2)
KNOB FOR ROLL
ADJUSTMENT
KNOB FOR PITCH
ADJUSTMENT
BACK OF MOUNT
ARROW INDICATES
FRONT OF MOUNT
To adjust yaw (swivel) for wood stud, concrete ceiling, and threaded rod mounting applications
:
Loosen
wood screws (
F
) if flush mounted to wood joists (page 5) or concrete ceilings (page 6), or loosen locknuts on
threaded rods (page 7), until projector mount can be rotated. Rotate mount to desired position and retighten
screws or locknuts.
To adjust yaw (swivel) for extension column applications
: Loosen screw on projector mount assembly (
A
)
indicated below until projector mount can be rotated. Rotate mount to desired position and retighten screw.
To adjust pitch (forward and backward tilt)
: Turn knob on back of mount as shown below. Pull knob out and
turn by hand for easy adjustment or insert #2 phillips screwdriver in end of knob and turn.
To adjust roll (side to side tilt)
: Turn knob on side of mount as shown below. Pull knob out and turn by hand for
easy adjustment or insert #2 phillips screwdriver in end of knob and turn.
A
To prevent tampering with the pitch and roll adjustments
:
Tighten the two tamper resistant security screws
on the projector mount assembly using 4 mm security allen wrench (
B
) to lock the pitch and roll adjustments as
shown below.
Note:
Tighten screws firmly, but do not overtighten. Overtightening can damage the mount.
SIDE VIEW
Projector Alignment
9-1
TO LOCK PITCH, TIGHTEN
TAMPER RESISTANT
SECURITY SCREW
© 2011, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
9
• Do not adjust pitch or roll while tamper resistant security screws are fully engaged.
• Loosen the two tamper resistant security screws one complete turn before adjusting the projector mount assembly
or damage may occur.
CAUTION