NordicTrack 9600 Treadmill English Manual - Page 31

TURNING THE WALKING PLATFORM, Remove the key and unplug the, power cord., REPLACING THE WALKING

Get NordicTrack 9600 Treadmill PDF manuals and user guides View all NordicTrack 9600 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

TURNING THE WALKING PLATFORM Both sides of the walking platform are designed to be used as walking surfaces. Inspect the walking platform periodically for wear. If there is any wood showing through the phenolic coating, or if the surface is damaged, the walking platform should be turned over. The walking platform will need to be turned over after every 16,000 to 19,500 kilometres. Follow the instructions below to turn over the walking platform. 1. Remove the key and unplug the power cord. Remove the two 1-3 Hood Screws (2) and lift off the 1 2 Motor Hood (1). Next, remove the two Rear Roller Bolts (82), the two Roller Guard Screws (80), and the Right and Left Roller 80 83 6 6 Guards (81, 83). 82 2. Remove the six Platform Screws 70 80 (6). Lift the Rear Roller (79) and slide it out of the Walking Belt (71). Lift the Walking Platform 81 6 82 (70) a few inches, slide it out of the Walking Belt, turn it over, and 71 then slide it back into the Walking 79 Belt. Slide the Rear Roller back into the Walking Belt. Reattach the six Platform Screws (6). 3. Reattach the Right and Left Roller Guards (81, 83) with the two Roller Guard Screws (80). Insert the Rear Roller Bolts (82) into the Roller Guards and thread them into the Rear Roller (79). Reattach the Motor Hood (1) with the two Hood Screws (2). 4. Next, the Walking Belt (71) will need to be adjusted to the proper tension. Using chalk, make two marks exactly 127 cm apart on the Walking Belt, as shown in the drawing. Tighten both Rear Roller Bolts (82) until the two chalk marks move apart an additional 5 to 6 mm. Make sure to keep the Walking Belt centered. 4 71 127 cm 82 REPLACING THE WALKING PLATFORM When both sides of the walking platform become worn, the walking platform should be replaced. The walking platform will need to be replaced after every 32,000 to 48,000 kilometres. Refer to page 42 to order a new walking platform. Follow the instructions above to replace the walking platform. REPLACING THE WALKING BELT When the walking belt becomes worn, it should be replaced. The walking belt will need to be replaced after every 32,000 to 48,000 kilometres. Refer to page 42 to order a new walking belt. 30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
TURNING THE WALKING PLATFORM
Both sides of the walking platform are designed to be used as walking surfaces. Inspect the walking platform peri-
odically for wear. If there is any wood showing through the phenolic coating, or if the surface is damaged, the
walking platform should be turned over. The walking platform will need to be turned over after every 16,000 to
19,500 kilometres. Follow the instructions below to turn over the walking platform.
1.
Remove the key and unplug the
power cord.
Remove the two
Hood Screws (2) and lift off the
Motor Hood (1). Next, remove the
two Rear Roller Bolts (82), the
two Roller Guard Screws (80),
and the Right and Left Roller
Guards (81, 83).
2. Remove the six Platform Screws
(6). Lift the Rear Roller (79) and
slide it out of the Walking Belt
(71). Lift the Walking Platform
(70) a few inches, slide it out of
the Walking Belt, turn it over, and
then slide it back into the Walking
Belt. Slide the Rear Roller back
into the Walking Belt. Reattach
the six Platform Screws (6).
3. Reattach the Right and Left Roller Guards (81, 83) with the two Roller Guard Screws (80). Insert the Rear
Roller Bolts (82) into the Roller Guards and thread them into the Rear Roller (79). Reattach the Motor Hood
(1) with the two Hood Screws (2).
4. Next, the Walking Belt (71) will need to be adjusted to the
proper tension. Using chalk, make two marks exactly 127
cm apart on the Walking Belt, as shown in the drawing.
Tighten both Rear Roller Bolts (82) until the two chalk
marks move apart an additional 5 to 6 mm. Make sure to
keep the Walking Belt centered.
REPLACING THE WALKING PLATFORM
When both sides of the walking platform become worn, the walking platform should be replaced. The walking
platform will need to be replaced after every 32,000 to 48,000 kilometres. Refer to page 42 to order a new walking
platform. Follow the instructions above to replace the walking platform.
REPLACING THE WALKING BELT
When the walking belt becomes worn, it should be replaced. The walking belt will need to be replaced after every
32,000 to 48,000 kilometres. Refer to page 42 to order a new walking belt.
30
6
6
6
80
80
82
82
70
79
71
1
2
81
83
127 cm
4
71
82
1–3