Oki B4300 OkiLAN 8100 SoftNIC User's Guide - Page 93

UNIX, Overview, Configuration, Network Interface card setting

Get Oki B4300 PDF manuals and user guides View all Oki B4300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 93 highlights

UNIX Overview The OkiLAN print server supports many protocols such as LPD, FTP, TELNET, SNMP and IPP, and works within the UNIX environment. To use the network card within the UNIX environment, the following steps are required: Configuration Network Interface card setting The first step in installing the network card under UNIX is to set up the IP address, Subnet Mask and Gateway. This section explains one way to set them up from a UNIX workstation. > The network addresses used in this manual are shown as examples only. Network addresses used in your installation must be generated for your own network. > Log in as [root] to change the configuration of the Print Server. By default, there is no root password. > If an incorrect IP address, Subnet Mask or Gateway is entered, the network may go down or other damage may occur. Check the address with your network manager. The following explanation uses Sun Solaris 2.8 (Solaris 8) as an example. The actual commands may differ between versions of UNIX, so refer to the workstation manuals for more information. 1. Log in as root to the workstation > If you do not have superuser rights, the network manger should conduct the configuration. 2. If the print server does not have an IP addresses already assigned, use the arp command to set a temporary IP address. Example: for IP address 192.68.20.127 and network card address 00:80:92:01:00:D2 UNIX 91

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
UNIX 91
UNIX
Overview
The OkiLAN print server supports many protocols such as LPD, FTP,
TELNET, SNMP and IPP, and works within the UNIX environment.
To use the network card within the UNIX environment, the following
steps are required:
Configuration
Network Interface card setting
The first step in installing the network card under UNIX is to set up the IP
address, Subnet Mask and Gateway. This section explains one way to set
them up from a UNIX workstation.
>
The network addresses used in this manual are shown as examples
only. Network addresses used in your installation must be generated
for your own network.
>
Log in as [root] to change the configuration of the Print Server. By
default, there is no root password.
>
If an incorrect IP address, Subnet Mask or Gateway is entered, the
network may go down or other damage may occur. Check the
address with your network manager.
The following explanation uses Sun Solaris 2.8 (Solaris 8) as an example.
The actual commands may differ between versions of UNIX, so refer to
the workstation manuals for more information.
1.
Log in as root to the workstation
>
If you do not have superuser rights, the network manger should
conduct the configuration.
2.
If the print server does not have an IP addresses already assigned,
use the arp command to set a temporary IP address.
Example: for IP address 192.68.20.127 and network card address
00:80:92:01:00:D2