Onkyo HT-S3500 Owner Manual - Page 57

■ The AV receiver's remote controller doesn't control my iPod/iPhone Make sure your iPod/iPhone is properly inserted in - the Dock. If your iPod/iPhone is in a case, it may not connect properly to the Dock. Always remove your iPod/iPhone from the case before inserting it into the Dock. The iPod/iPhone cannot be operated while it's - displaying the Apple logo. Make sure you've selected the right remote mode. 49 When you use the AV receiver's remote controller, - point it toward your AV receiver. If you still can't control your iPod/iPhone, start - playback by pressing your iPod/iPhone model's Play button. Remote operation should then be possible. Try resetting your iPod/iPhone. - Depending on your iPod/iPhone, some buttons may - not work as expected. ■ The AV receiver unexpectedly selects my iPod/iPhone as the input source Always pause iPod/iPhone playback before selecting - a different input source. If playback is not paused, the Direct Change function may select your iPod/iPhone as the input source by mistake during the transition between tracks. ■ iPod/iPhone doesn't work properly Try reconnecting your iPod/iPhone. - Recording ■ Can't record On your recorder, make sure the correct input is - selected. To prevent signal loops and damage to the AV - receiver, input signals are not fed through to outputs with the same name (e.g., VCR/DVR IN to VCR/DVR OUT). USB Device Playback ■ Can't access the music files on a USB device Make sure the USB device is plugged in properly. - The AV receiver supports USB devices that support 63 the USB mass storage device class. However, playback may not be possible with some USB devices even if they conform to the USB mass storage device class. USB memory devices with security functions cannot 24 be played. Others ■ Standby power consumption In the following cases, the power consumption in 45 standby mode may reach up to a maximum of 31 W: - "HDMI Ctrl (RIHD)" setting is set to "On". (Depending on the TV status, the AV receiver will enter standby mode as usual.) - The "HDMI Through" setting is set to other than "Off". ■ The sound changes when I connect my headphones When a pair of headphones is connected, the listening - mode is set to Stereo, unless it's already set to Stereo, Mono, or Direct. ■ How do I change the language of a multiplex source Use the "Input Ch (Mux)" setting on the "Audio 42 Adjust" menu to select "Main" or "Sub". ■ The V functions don't work To use V, you must make an V connection and an 18 analog audio connection (RCA) between the component and AV receiver, even if they are connected digitally. Appendix ■ The following settings can be made for the composite video inputs You must use the buttons on the unit to make these settings. On the AV receiver, press the input selector for the input source that you want to set and the SETUP button simultaneously. While holding down the input selector button, press SETUP until "Video ATT :On" appears on the AV receiver's display. Then, release both buttons. To turn the setting off, repeat the above process so that "Video ATT :Off" appears on the AV receiver's display, and release the buttons. • Video Attenuation This setting can be made for the BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX, or USB input. If you have a games console connected to the composite video input, and the picture isn't very clear, you can attenuate the gain. Video ATT :Off: (default). Video ATT :On: Gain is reduced by 2 dB. ■ If the picture on your TV/monitor connected to the HDMI OUT is unstable, try switching the DeepColor function off To turn off the DeepColor function, simultaneously press the CBL/SAT and ON/STANDBY buttons on the AV receiver. While holding down CBL/SAT, press ON/STANDBY until "Deep Color: Off" appears on the AV receiver's display. Then, release both buttons. To reactivate the DeepColor function, repeat the above process until "Deep Color: On" appears on the AV receiver's display and release the buttons. En-57